linux-stable.git/drivers/usb, branch v5.18.3 Linux kernel stable tree xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI 2022-06-09T08:29:29+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2022-05-11T22:04:50+00:00 ebaccc6ff2b2dcc9619aab6c2f9fa1118ff7047a commit 74f55a62c4c354f43a6d75f77dd184c4f57b9a26 upstream. Alder Lake N TCSS xHCI needs to be runtime suspended whenever possible to allow the TCSS hardware block to enter D3 and thus save energy Cc: stable@kernel.org Suggested-by: Gopal Vamshi Krishna <vamshi.krishna.gopal@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220511220450.85367-10-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 74f55a62c4c354f43a6d75f77dd184c4f57b9a26 upstream.

Alder Lake N TCSS xHCI needs to be runtime suspended whenever possible
to allow the TCSS hardware block to enter D3 and thus save energy

Cc: stable@kernel.org
Suggested-by: Gopal Vamshi Krishna <vamshi.krishna.gopal@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Set HCD flag to defer primary roothub registration 2022-06-09T08:29:29+00:00 Kishon Vijay Abraham I kishon@ti.com 2022-05-10T09:16:30+00:00 6c64a664e1cff339ec698d803fa8cbb9af5d95ce commit b7a4f9b5d0e4b6dd937678c546c0b322dd1a4054 upstream. Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer registering primary roothub in usb_add_hcd() if xhci has two roothubs. This will make sure both primary roothub and secondary roothub will be registered along with the second HCD. This is required for cold plugged USB devices to be detected in certain PCIe USB cards (like Inateck USB card connected to AM64 EVM or J7200 EVM). This patch has been added and reverted earier as it triggered a race in usb device enumeration. That race is now fixed in 5.16-rc3, and in stable back to 5.4 commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex") commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race") [minor rebase change, and commit message update -Mathias] CC: stable@vger.kernel.org # 5.4+ Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com> Tested-by: Chris Chiu <chris.chiu@canonical.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Link: https://lore.kernel.org/r/20220510091630.16564-3-kishon@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit b7a4f9b5d0e4b6dd937678c546c0b322dd1a4054 upstream.

Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer
registering primary roothub in usb_add_hcd() if xhci has two roothubs.
This will make sure both primary roothub and secondary roothub will be
registered along with the second HCD.
This is required for cold plugged USB devices to be detected in certain
PCIe USB cards (like Inateck USB card connected to AM64 EVM or J7200 EVM).

This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0
race")

[minor rebase change, and commit message update -Mathias]

CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-3-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: core: hcd: Add support for deferring roothub registration 2022-06-09T08:29:28+00:00 Kishon Vijay Abraham I kishon@ti.com 2022-05-10T09:16:29+00:00 520cb9843336c49496691ee3900a70867effccab commit a44623d9279086c89f631201d993aa332f7c9e66 upstream. It has been observed with certain PCIe USB cards (like Inateck connected to AM64 EVM or J7200 EVM) that as soon as the primary roothub is registered, port status change is handled even before xHC is running leading to cold plug USB devices not detected. For such cases, registering both the root hubs along with the second HCD is required. Add support for deferring roothub registration in usb_add_hcd(), so that both primary and secondary roothubs are registered along with the second HCD. This patch has been added and reverted earier as it triggered a race in usb device enumeration. That race is now fixed in 5.16-rc3, and in stable back to 5.4 commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex") commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race") CC: stable@vger.kernel.org # 5.4+ Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com> Tested-by: Chris Chiu <chris.chiu@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Link: https://lore.kernel.org/r/20220510091630.16564-2-kishon@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a44623d9279086c89f631201d993aa332f7c9e66 upstream.

It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.

This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0
race")

CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: dwc3: gadget: Move null pinter check to proper place 2022-06-09T08:29:28+00:00 Albert Wang albertccwang@google.com 2022-05-18T06:13:15+00:00 5cdc317e6274c83094e94f0a940e971f608998b8 commit 3c5880745b4439ac64eccdb040e37fc1cc4c5406 upstream. When dwc3_gadget_ep_cleanup_completed_requests() called to dwc3_gadget_giveback() where the dwc3 lock is released, other thread is able to execute. In this situation, usb_ep_disable() gets the chance to clear endpoint descriptor pointer which leds to the null pointer dereference problem. So needs to move the null pointer check to a proper place. Example call stack: Thread#1: dwc3_thread_interrupt() spin_lock -> dwc3_process_event_buf() -> dwc3_process_event_entry() -> dwc3_endpoint_interrupt() -> dwc3_gadget_endpoint_trbs_complete() -> dwc3_gadget_ep_cleanup_completed_requests() ... -> dwc3_giveback() spin_unlock Thread#2 executes Thread#2: configfs_composite_disconnect() -> __composite_disconnect() -> ffs_func_disable() -> ffs_func_set_alt() -> ffs_func_eps_disable() -> usb_ep_disable() wait for dwc3 spin_lock Thread#1 released lock clear endpoint.desc Fixes: 26288448120b ("usb: dwc3: gadget: Fix null pointer exception") Cc: stable <stable@kernel.org> Signed-off-by: Albert Wang <albertccwang@google.com> Link: https://lore.kernel.org/r/20220518061315.3359198-1-albertccwang@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 3c5880745b4439ac64eccdb040e37fc1cc4c5406 upstream.

When dwc3_gadget_ep_cleanup_completed_requests() called to
dwc3_gadget_giveback() where the dwc3 lock is released, other thread is
able to execute. In this situation, usb_ep_disable() gets the chance to
clear endpoint descriptor pointer which leds to the null pointer
dereference problem. So needs to move the null pointer check to a proper
place.

Example call stack:

Thread#1:
dwc3_thread_interrupt()
  spin_lock
  -> dwc3_process_event_buf()
   -> dwc3_process_event_entry()
    -> dwc3_endpoint_interrupt()
     -> dwc3_gadget_endpoint_trbs_complete()
      -> dwc3_gadget_ep_cleanup_completed_requests()
       ...
       -> dwc3_giveback()
          spin_unlock
          Thread#2 executes

Thread#2:
configfs_composite_disconnect()
  -> __composite_disconnect()
   -> ffs_func_disable()
    -> ffs_func_set_alt()
     -> ffs_func_eps_disable()
      -> usb_ep_disable()
         wait for dwc3 spin_lock
         Thread#1 released lock
         clear endpoint.desc

Fixes: 26288448120b ("usb: dwc3: gadget: Fix null pointer exception")
Cc: stable <stable@kernel.org>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20220518061315.3359198-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: isp1760: Fix out-of-bounds array access 2022-06-09T08:29:28+00:00 Linus Walleij linus.walleij@linaro.org 2022-05-16T09:14:24+00:00 463bddd3ff1acf4036ddb80c34a715eb99debf46 commit 26ae2c942b5702f2e43d36b2a4389cfb7d616b6a upstream. Running the driver through kasan gives an interesting splat: BUG: KASAN: global-out-of-bounds in isp1760_register+0x180/0x70c Read of size 20 at addr f1db2e64 by task swapper/0/1 (...) isp1760_register from isp1760_plat_probe+0x1d8/0x220 (...) This happens because the loop reading the regmap fields for the different ISP1760 variants look like this: for (i = 0; i < HC_FIELD_MAX; i++) { ... } Meaning it expects the arrays to be at least HC_FIELD_MAX - 1 long. However the arrays isp1760_hc_reg_fields[], isp1763_hc_reg_fields[], isp1763_hc_volatile_ranges[] and isp1763_dc_volatile_ranges[] are dynamically sized during compilation. Fix this by putting an empty assignment to the [HC_FIELD_MAX] and [DC_FIELD_MAX] array member at the end of each array. This will make the array one member longer than it needs to be, but avoids the risk of overwriting whatever is inside [HC_FIELD_MAX - 1] and is simple and intuitive to read. Also add comments explaining what is going on. Fixes: 1da9e1c06873 ("usb: isp1760: move to regmap for register access") Cc: stable@vger.kernel.org Cc: Rui Miguel Silva <rui.silva@linaro.org> Cc: Dietmar Eggemann <dietmar.eggemann@arm.com> Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20220516091424.391209-1-linus.walleij@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 26ae2c942b5702f2e43d36b2a4389cfb7d616b6a upstream.

Running the driver through kasan gives an interesting splat:

  BUG: KASAN: global-out-of-bounds in isp1760_register+0x180/0x70c
  Read of size 20 at addr f1db2e64 by task swapper/0/1
  (...)
  isp1760_register from isp1760_plat_probe+0x1d8/0x220
  (...)

This happens because the loop reading the regmap fields for the
different ISP1760 variants look like this:

  for (i = 0; i < HC_FIELD_MAX; i++) { ... }

Meaning it expects the arrays to be at least HC_FIELD_MAX - 1 long.

However the arrays isp1760_hc_reg_fields[], isp1763_hc_reg_fields[],
isp1763_hc_volatile_ranges[] and isp1763_dc_volatile_ranges[] are
dynamically sized during compilation.

Fix this by putting an empty assignment to the [HC_FIELD_MAX]
and [DC_FIELD_MAX] array member at the end of each array.
This will make the array one member longer than it needs to be,
but avoids the risk of overwriting whatever is inside
[HC_FIELD_MAX - 1] and is simple and intuitive to read. Also
add comments explaining what is going on.

Fixes: 1da9e1c06873 ("usb: isp1760: move to regmap for register access")
Cc: stable@vger.kernel.org
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220516091424.391209-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: new quirk for Dell Gen 2 devices 2022-06-09T08:29:28+00:00 Monish Kumar R monish.kumar.r@intel.com 2022-05-20T13:00:44+00:00 5528be7896a85d9102c1a91dec7a6841ac3ad75f commit 97fa5887cf283bb75ffff5f6b2c0e71794c02400 upstream. Add USB_QUIRK_NO_LPM and USB_QUIRK_RESET_RESUME quirks for Dell usb gen 2 device to not fail during enumeration. Found this bug on own testing Signed-off-by: Monish Kumar R <monish.kumar.r@intel.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220520130044.17303-1-monish.kumar.r@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 97fa5887cf283bb75ffff5f6b2c0e71794c02400 upstream.

Add USB_QUIRK_NO_LPM and USB_QUIRK_RESET_RESUME quirks for Dell usb gen
2 device to not fail during enumeration.

Found this bug on own testing

Signed-off-by: Monish Kumar R <monish.kumar.r@intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220520130044.17303-1-monish.kumar.r@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: option: add Quectel BG95 modem 2022-06-09T08:29:27+00:00 Carl Yin(殷张成) carl.yin@quectel.com 2022-05-19T02:34:43+00:00 a128ee79e9f76fff0f68e9b9845ba68a2d444ea6 commit 33b7af2f459df453feb0d44628d820c47fefe7a8 upstream. The BG95 modem has 3 USB configurations that are configurable via the AT command AT+QCFGEXT="usbnet",["ecm"|"modem"|"rmnet"] which make the modem enumerate with the following interfaces, respectively: "modem": Diag + GNSS + Modem + Modem "ecm" : Diag + GNSS + Modem + ECM "rmnet": Diag + GNSS + Modem + QMI Don't support Full QMI messages (e.g WDS_START_NETWORK_INTERFACE) A detailed description of the USB configuration for each mode follows: +QCFGEXT: "usbnet","modem" -------------------------- T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0700 Rev= 0.00 S: Manufacturer=Quectel, Incorporated S: Product=Quectel LPWA Module S: SerialNumber=884328a2 C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms +QCFGEXT: "usbnet","ecm" ------------------------ T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0700 Rev= 0.00 S: Manufacturer=Quectel, Incorporated S: Product=Quectel LPWA Module S: SerialNumber=884328a2 C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA A: FirstIf#= 3 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00 I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms I: If#= 4 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether I:* If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms +QCFGEXT: "usbnet","rmnet" -------------------------- T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0700 Rev= 0.00 S: Manufacturer=Quectel, Incorporated S: Product=Quectel LPWA Module S: SerialNumber=884328a2 C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Carl Yin <carl.yin@quectel.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 33b7af2f459df453feb0d44628d820c47fefe7a8 upstream.

The BG95 modem has 3 USB configurations that are configurable via the AT
command AT+QCFGEXT="usbnet",["ecm"|"modem"|"rmnet"] which make the modem
enumerate with the following interfaces, respectively:

"modem": Diag + GNSS + Modem + Modem
"ecm"  : Diag + GNSS + Modem + ECM
"rmnet": Diag + GNSS + Modem + QMI
         Don't support Full QMI messages (e.g WDS_START_NETWORK_INTERFACE)

A detailed description of the USB configuration for each mode follows:

+QCFGEXT: "usbnet","modem"
--------------------------
T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0700 Rev= 0.00
S:  Manufacturer=Quectel, Incorporated
S:  Product=Quectel LPWA Module
S:  SerialNumber=884328a2
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

+QCFGEXT: "usbnet","ecm"
------------------------
T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0700 Rev= 0.00
S:  Manufacturer=Quectel, Incorporated
S:  Product=Quectel LPWA Module
S:  SerialNumber=884328a2
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
A:  FirstIf#= 3 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
I:  If#= 4 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

+QCFGEXT: "usbnet","rmnet"
--------------------------
T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0700 Rev= 0.00
S:  Manufacturer=Quectel, Incorporated
S:  Product=Quectel LPWA Module
S:  SerialNumber=884328a2
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Carl Yin <carl.yin@quectel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: pl2303: fix type detection for odd device 2022-06-09T08:29:27+00:00 Johan Hovold johan@kernel.org 2022-05-17T16:17:36+00:00 f2170f29ff19f2b253e9d8257408b01bd5c1c951 commit e82e7c6dde91acd6748d672a44dc1980ce239f86 upstream. At least one pl2303 device has a bcdUSB of 1.0.1 which most likely was was intended as 1.1. Allow bcdDevice 1.0.1 but interpret it as 1.1. Fixes: 1e9faef4d26d ("USB: serial: pl2303: fix HX type detection") Cc: stable@vger.kernel.org # 5.13 Link: https://lore.kernel.org/linux-usb/CAJixRzqf4a9-ZKZDgWxicc_BpfdZVE9qqGmkiO7xEstOXUbGvQ@mail.gmail.com Reported-by: Gary van der Merwe <gary.vandermerwe@fnb.co.za> Link: https://lore.kernel.org/r/20220517161736.13313-1-johan@kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit e82e7c6dde91acd6748d672a44dc1980ce239f86 upstream.

At least one pl2303 device has a bcdUSB of 1.0.1 which most likely was
was intended as 1.1.

Allow bcdDevice 1.0.1 but interpret it as 1.1.

Fixes: 1e9faef4d26d ("USB: serial: pl2303: fix HX type detection")
Cc: stable@vger.kernel.org      # 5.13
Link: https://lore.kernel.org/linux-usb/CAJixRzqf4a9-ZKZDgWxicc_BpfdZVE9qqGmkiO7xEstOXUbGvQ@mail.gmail.com
Reported-by: Gary van der Merwe <gary.vandermerwe@fnb.co.za>
Link: https://lore.kernel.org/r/20220517161736.13313-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'usb-serial-5.18-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial 2022-05-13T06:29:40+00:00 Greg Kroah-Hartman gregkh@linuxfoundation.org 2022-05-13T06:29:40+00:00 757b9f6e6a2070043e5f215ff4afe350ecfb2bf7 Johan writes: USB-serial fixes for 5.18-rc7 Here are some new device ids. All have been in linux-next with no reported issues. * tag 'usb-serial-5.18-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: qcserial: add support for Sierra Wireless EM7590 USB: serial: option: add Fibocom MA510 modem USB: serial: option: add Fibocom L610 modem USB: serial: pl2303: add device id for HP LM930 Display 
Johan writes:

USB-serial fixes for 5.18-rc7

Here are some new device ids.

All have been in linux-next with no reported issues.

* tag 'usb-serial-5.18-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: qcserial: add support for Sierra Wireless EM7590
  USB: serial: option: add Fibocom MA510 modem
  USB: serial: option: add Fibocom L610 modem
  USB: serial: pl2303: add device id for HP LM930 Display
usb: xhci-mtk: remove bandwidth budget table 2022-05-12T16:35:38+00:00 Chunfeng Yun chunfeng.yun@mediatek.com 2022-05-12T06:49:31+00:00 1645eee0d7f623660e6ce0f1aef4591788a0c9da The bandwidth budget table is introduced to trace ideal bandwidth used by each INT/ISOC endpoint, but in fact the endpoint may consume more bandwidth and cause data transfer error, so it's better to leave some margin. Obviously it's difficult to find the best margin for all cases, instead take use of the worst-case scenario. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/20220512064931.31670-2-chunfeng.yun@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
The bandwidth budget table is introduced to trace ideal bandwidth used
by each INT/ISOC endpoint, but in fact the endpoint may consume more
bandwidth and cause data transfer error, so it's better to leave some
margin. Obviously it's difficult to find the best margin for all cases,
instead take use of the worst-case scenario.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220512064931.31670-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>