linux-stable.git/drivers/usb, branch v5.1.2

UAS: fix alignment of scatter/gather segments

2019-05-11T05:49:56+00:00

commit 3ae62a42090f1ed48e2313ed256a1182a85fb575 upstream.

This is the UAS version of

747668dbc061b3e62bc1982767a3a1f9815fcf0e
usb-storage: Set virt_boundary_mask to avoid SG overflows

We are not as likely to be vulnerable as storage, as it is unlikelier
that UAS is run over a controller without native support for SG,
but the issue exists.
The issue has been existing since the inception of the driver.

Fixes: 115bb1ffa54c ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

soc: sunxi: Fix missing dependency on REGMAP_MMIO

2019-05-11T05:49:55+00:00

commit a84014e1db35d8e7af09878d0b4bf30804fb17d5 upstream.

When enabling ARCH_SUNXI from allnoconfig, SUNXI_SRAM is enabled, but
not REGMAP_MMIO, so the kernel fails to link with an undefined reference
to __devm_regmap_init_mmio_clk. Select REGMAP_MMIO, as suggested in
drivers/base/regmap/Kconfig.

This creates the following dependency loop:

  drivers/of/Kconfig:68:                symbol OF_IRQ depends on IRQ_DOMAIN
  kernel/irq/Kconfig:63:                symbol IRQ_DOMAIN is selected by REGMAP
  drivers/base/regmap/Kconfig:7:        symbol REGMAP default is visible depending on REGMAP_MMIO
  drivers/base/regmap/Kconfig:39:       symbol REGMAP_MMIO is selected by SUNXI_SRAM
  drivers/soc/sunxi/Kconfig:4:          symbol SUNXI_SRAM is selected by USB_MUSB_SUNXI
  drivers/usb/musb/Kconfig:63:          symbol USB_MUSB_SUNXI depends on GENERIC_PHY
  drivers/phy/Kconfig:7:                symbol GENERIC_PHY is selected by PHY_BCM_NS_USB3
  drivers/phy/broadcom/Kconfig:29:      symbol PHY_BCM_NS_USB3 depends on MDIO_BUS
  drivers/net/phy/Kconfig:12:           symbol MDIO_BUS default is visible depending on PHYLIB
  drivers/net/phy/Kconfig:181:          symbol PHYLIB is selected by ARC_EMAC_CORE
  drivers/net/ethernet/arc/Kconfig:18:  symbol ARC_EMAC_CORE is selected by ARC_EMAC
  drivers/net/ethernet/arc/Kconfig:24:  symbol ARC_EMAC depends on OF_IRQ

To fix the circular dependency, make USB_MUSB_SUNXI select GENERIC_PHY
instead of depending on it. This matches the use of GENERIC_PHY by all
but two other drivers.

Cc:  # 4.19
Fixes: 5828729bebbb ("soc: sunxi: export a regmap for EMAC clock reg on A64")
Signed-off-by: Samuel Holland 
Acked-by: Maxime Ripard 
Signed-off-by: Bin Liu 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

usb-storage: Set virt_boundary_mask to avoid SG overflows

2019-05-11T05:49:54+00:00

commit 747668dbc061b3e62bc1982767a3a1f9815fcf0e upstream.

The USB subsystem has always had an unusual requirement for its
scatter-gather transfers: Each element in the scatterlist (except the
last one) must have a length divisible by the bulk maxpacket size.
This is a particular issue for USB mass storage, which uses SG lists
created by the block layer rather than setting up its own.

So far we have scraped by okay because most devices have a logical
block size of 512 bytes or larger, and the bulk maxpacket sizes for
USB 2 and below are all <= 512.  However, USB 3 has a bulk maxpacket
size of 1024.  Since the xhci-hcd driver includes native SG support,
this hasn't mattered much.  But now people are trying to use USB-3
mass storage devices with USBIP, and the vhci-hcd driver currently
does not have full SG support.

The result is an overflow error, when the driver attempts to implement
an SG transfer of 63 512-byte blocks as a single
3584-byte (7 blocks) transfer followed by seven 4096-byte (8 blocks)
transfers.  The device instead sends 31 1024-byte packets followed by
a 512-byte packet, and this overruns the first SG buffer.

Ideally this would be fixed by adding better SG support to vhci-hcd.
But for now it appears we can work around the problem by
asking the block layer to respect the maxpacket limitation, through
the use of the virt_boundary_mask.

Signed-off-by: Alan Stern 
Reported-by: Seth Bollinger 
Tested-by: Seth Bollinger 
CC: Ming Lei 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: cdc-acm: fix unthrottle races

2019-05-11T05:49:54+00:00

commit 764478f41130f1b8d8057575b89e69980a0f600d upstream.

Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().

First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.

	CPU 1				CPU 2
	================		================
	complete()			unthrottle()
	  process_urb();
	  smp_mb__before_atomic();
	  set_bit(i, free);		  if (test_and_clear_bit(i, free))
						  submit_urb();

Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.

	CPU 1				CPU 2
	================		================
	complete()			unthrottle()
	  set_bit(i, free);		  throttled = 0;
	  smp_mb__after_atomic();	  smp_mb();
	  if (throttled)		  if (test_and_clear_bit(i, free))
		  return;			  submit_urb();

Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.

Also note that the first race was fixed by 36e59e0d70d6 ("cdc-acm: fix
race between callback and unthrottle") back in 2015, but the bug was
reintroduced a year later.

Fixes: 1aba579f3cf5 ("cdc-acm: handle read pipe errors")
Fixes: 088c64f81284 ("USB: cdc-acm: re-write read processing")
Signed-off-by: Johan Hovold 
Acked-by: Oliver Neukum 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

USB: serial: f81232: fix interrupt worker not stop

2019-05-11T05:49:54+00:00

commit 804dbee1e49774918339c1e5a87400988c0819e8 upstream.

The F81232 will use interrupt worker to handle MSR change.
This patch will fix the issue that interrupt work should stop
in close() and suspend().

This also fixes line-status events being disabled after a suspend cycle
until the port is re-opened.

Signed-off-by: Ji-Ze Hong (Peter Hong) 
[ johan: amend commit message ]
Fixes: 87fe5adcd8de ("USB: f81232: implement read IIR/MSR with endpoint")
Cc: stable 	# 4.1
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

usb: dwc3: Fix default lpm_nyet_threshold value

2019-05-11T05:49:54+00:00

commit 8d791929b2fbdf7734c1596d808e55cb457f4562 upstream.

The max possible value for DCTL.LPM_NYET_THRES is 15 and not 255. Change
the default value to 15.

Cc: stable@vger.kernel.org
Fixes: 80caf7d21adc ("usb: dwc3: add lpm erratum support")
Signed-off-by: Thinh Nguyen 
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

usb: dwc3: Allow building USB_DWC3_QCOM without EXTCON

2019-05-11T05:49:53+00:00

commit 77a4946516fe488b6a33390de6d749f934a243ba upstream.

Keep EXTCON support optional, as some platforms do not need it.

Do the same for USB_DWC3_OMAP while we're at it.

Fixes: 3def4031b3e3f ("usb: dwc3: add EXTCON dependency for qcom")
Signed-off-by: Marc Gonzalez 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: yurex: Fix protection fault after device removal

2019-04-25T09:11:41+00:00

The syzkaller USB fuzzer found a general-protection-fault bug in the
yurex driver.  The fault occurs when a device has been unplugged; the
driver's interrupt-URB handler logs an error message referring to the
device by name, after the device has been unregistered and its name
deallocated.

This problem is caused by the fact that the interrupt URB isn't
cancelled until the driver's private data structure is released, which
can happen long after the device is gone.  The cure is to make sure
that the interrupt URB is killed before yurex_disconnect() returns;
this is exactly the sort of thing that usb_poison_urb() was meant for.

Signed-off-by: Alan Stern 
Reported-and-tested-by: syzbot+2eb9121678bdb36e6d57@syzkaller.appspotmail.com
CC: 
Signed-off-by: Greg Kroah-Hartman

usb: usbip: fix isoc packet num validation in get_pipe

2019-04-25T09:11:41+00:00

Change the validation of number_of_packets in get_pipe to compare the
number of packets to a fixed maximum number of packets allowed, set to
be 1024. This number was chosen due to it being used by other drivers as
well, for example drivers/usb/host/uhci-q.c

Background/reason:
The get_pipe function in stub_rx.c validates the number of packets in
isochronous mode and aborts with an error if that number is too large,
in order to prevent malicious input from possibly triggering large
memory allocations. This was previously done by checking whether
pdu->u.cmd_submit.number_of_packets is bigger than the number of packets
that would be needed for pdu->u.cmd_submit.transfer_buffer_length bytes
if all except possibly the last packet had maximum length, given by
usb_endpoint_maxp(epd) *  usb_endpoint_maxp_mult(epd). This leads to an
error if URBs with packets shorter than the maximum possible length are
submitted, which is allowed according to
Documentation/driver-api/usb/URB.rst and occurs for example with the
snd-usb-audio driver.

Fixes: c6688ef9f297 ("usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input")
Signed-off-by: Malte Leip 
Cc: stable 
Acked-by: Shuah Khan 
Signed-off-by: Greg Kroah-Hartman

USB: core: Fix bug caused by duplicate interface PM usage counter

2019-04-19T19:15:13+00:00

The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter.  This allowed
a hub to be runtime suspended at a time when the driver did not expect
it.  The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:

	URB 0000000031fb463e submitted while active
	WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363

The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count).  The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.

Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls.  In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.

This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative.  There's
even a warning about this in the USB power management documentation!

As it happens, this is exactly what the hub driver does.  The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread.  This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.

It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock.  The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts.  As far as I know, all
existing drivers currently do this.

Signed-off-by: Alan Stern 
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: 
Signed-off-by: Greg Kroah-Hartman