linux-stable.git/drivers/usb, branch v4.9.296

usb: gadget: f_fs: Clear ffs_eventfd in ffs_data_clear.

2022-01-05T11:31:25+00:00

commit b1e0887379422975f237d43d8839b751a6bcf154 upstream.

ffs_data_clear is indirectly called from both ffs_fs_kill_sb and
ffs_ep0_release, so it ends up being called twice when userland closes ep0
and then unmounts f_fs.
If userland provided an eventfd along with function's USB descriptors, it
ends up calling eventfd_ctx_put as many times, causing a refcount
underflow.
NULL-ify ffs_eventfd to prevent these extraneous eventfd_ctx_put calls.

Also, set epfiles to NULL right after de-allocating it, for readability.

For completeness, ffs_data_clear actually ends up being called thrice, the
last call being before the whole ffs structure gets freed, so when this
specific sequence happens there is a second underflow happening (but not
being reported):

/sys/kernel/debug/tracing# modprobe usb_f_fs
/sys/kernel/debug/tracing# echo ffs_data_clear > set_ftrace_filter
/sys/kernel/debug/tracing# echo function > current_tracer
/sys/kernel/debug/tracing# echo 1 > tracing_on
(setup gadget, run and kill function userland process, teardown gadget)
/sys/kernel/debug/tracing# echo 0 > tracing_on
/sys/kernel/debug/tracing# cat trace
 smartcard-openp-436     [000] .....  1946.208786: ffs_data_clear <-ffs_data_closed
 smartcard-openp-431     [000] .....  1946.279147: ffs_data_clear <-ffs_data_closed
 smartcard-openp-431     [000] .n...  1946.905512: ffs_data_clear <-ffs_data_put

Warning output corresponding to above trace:
[ 1946.284139] WARNING: CPU: 0 PID: 431 at lib/refcount.c:28 refcount_warn_saturate+0x110/0x15c
[ 1946.293094] refcount_t: underflow; use-after-free.
[ 1946.298164] Modules linked in: usb_f_ncm(E) u_ether(E) usb_f_fs(E) hci_uart(E) btqca(E) btrtl(E) btbcm(E) btintel(E) bluetooth(E) nls_ascii(E) nls_cp437(E) vfat(E) fat(E) bcm2835_v4l2(CE) bcm2835_mmal_vchiq(CE) videobuf2_vmalloc(E) videobuf2_memops(E) sha512_generic(E) videobuf2_v4l2(E) sha512_arm(E) videobuf2_common(E) videodev(E) cpufreq_dt(E) snd_bcm2835(CE) brcmfmac(E) mc(E) vc4(E) ctr(E) brcmutil(E) snd_soc_core(E) snd_pcm_dmaengine(E) drbg(E) snd_pcm(E) snd_timer(E) snd(E) soundcore(E) drm_kms_helper(E) cec(E) ansi_cprng(E) rc_core(E) syscopyarea(E) raspberrypi_cpufreq(E) sysfillrect(E) sysimgblt(E) cfg80211(E) max17040_battery(OE) raspberrypi_hwmon(E) fb_sys_fops(E) regmap_i2c(E) ecdh_generic(E) rfkill(E) ecc(E) bcm2835_rng(E) rng_core(E) vchiq(CE) leds_gpio(E) libcomposite(E) fuse(E) configfs(E) ip_tables(E) x_tables(E) autofs4(E) ext4(E) crc16(E) mbcache(E) jbd2(E) crc32c_generic(E) sdhci_iproc(E) sdhci_pltfm(E) sdhci(E)
[ 1946.399633] CPU: 0 PID: 431 Comm: smartcard-openp Tainted: G         C OE     5.15.0-1-rpi #1  Debian 5.15.3-1
[ 1946.417950] Hardware name: BCM2835
[ 1946.425442] Backtrace:
[ 1946.432048] [] (dump_backtrace) from [] (show_stack+0x20/0x24)
[ 1946.448226]  r7:00000009 r6:0000001c r5:c04a948c r4:c0a64e2c
[ 1946.458412] [] (show_stack) from [] (dump_stack+0x28/0x30)
[ 1946.470380] [] (dump_stack) from [] (__warn+0xe8/0x154)
[ 1946.482067]  r5:c04a948c r4:c0a71dc8
[ 1946.490184] [] (__warn) from [] (warn_slowpath_fmt+0xa0/0xe4)
[ 1946.506758]  r7:00000009 r6:0000001c r5:c0a71dc8 r4:c0a71e04
[ 1946.517070] [] (warn_slowpath_fmt) from [] (refcount_warn_saturate+0x110/0x15c)
[ 1946.535309]  r8:c0100224 r7:c0dfcb84 r6:ffffffff r5:c3b84c00 r4:c24a17c0
[ 1946.546708] [] (refcount_warn_saturate) from [] (eventfd_ctx_put+0x48/0x74)
[ 1946.564476] [] (eventfd_ctx_put) from [] (ffs_data_clear+0xd0/0x118 [usb_f_fs])
[ 1946.582664]  r5:c3b84c00 r4:c2695b00
[ 1946.590668] [] (ffs_data_clear [usb_f_fs]) from [] (ffs_data_closed+0x9c/0x150 [usb_f_fs])
[ 1946.609608]  r5:bf54d014 r4:c2695b00
[ 1946.617522] [] (ffs_data_closed [usb_f_fs]) from [] (ffs_fs_kill_sb+0x2c/0x30 [usb_f_fs])
[ 1946.636217]  r7:c0dfcb84 r6:c3a12260 r5:bf54d014 r4:c229f000
[ 1946.646273] [] (ffs_fs_kill_sb [usb_f_fs]) from [] (deactivate_locked_super+0x54/0x9c)
[ 1946.664893]  r5:bf54d014 r4:c229f000
[ 1946.672921] [] (deactivate_locked_super) from [] (deactivate_super+0x60/0x64)
[ 1946.690722]  r5:c2a09000 r4:c229f000
[ 1946.698706] [] (deactivate_super) from [] (cleanup_mnt+0xe4/0x14c)
[ 1946.715553]  r5:c2a09000 r4:00000000
[ 1946.723528] [] (cleanup_mnt) from [] (__cleanup_mnt+0x1c/0x20)
[ 1946.739922]  r7:c0dfcb84 r6:c3a12260 r5:c3a126fc r4:00000000
[ 1946.750088] [] (__cleanup_mnt) from [] (task_work_run+0x84/0xb8)
[ 1946.766602] [] (task_work_run) from [] (do_work_pending+0x470/0x56c)
[ 1946.783540]  r7:5ac3c35a r6:c0d0424c r5:c200bfb0 r4:c200a000
[ 1946.793614] [] (do_work_pending) from [] (slow_work_pending+0xc/0x20)
[ 1946.810553] Exception stack(0xc200bfb0 to 0xc200bff8)
[ 1946.820129] bfa0:                                     00000000 00000000 000000aa b5e21430
[ 1946.837104] bfc0: bef867a0 00000001 bef86840 00000034 bef86838 bef86790 bef86794 bef867a0
[ 1946.854125] bfe0: 00000000 bef86798 b67b7a1c b6d626a4 60000010 b5a23760
[ 1946.865335]  r10:00000000 r9:c200a000 r8:c0100224 r7:00000034 r6:bef86840 r5:00000001
[ 1946.881914]  r4:bef867a0
[ 1946.888793] ---[ end trace 7387f2a9725b28d0 ]---

Fixes: 5e33f6fdf735 ("usb: gadget: ffs: add eventfd notification about ffs events")
Cc: stable 
Signed-off-by: Vincent Pelletier 
Link: https://lore.kernel.org/r/f79eeea29f3f98de6782a064ec0f7351ad2f598f.1639793920.git.plr.vincent@gmail.com
Signed-off-by: Greg Kroah-Hartman

xhci: Fresco FL1100 controller should not have BROKEN_MSI quirk set.

2022-01-05T11:31:25+00:00

commit e4844092581ceec22489b66c42edc88bc6079783 upstream.

The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like
other Fresco controllers, but should not have the BROKEN_MSI quirks set.

BROKEN_MSI quirk causes issues in detecting usb drives connected to docks
with this FL1100 controller.
The BROKEN_MSI flag was apparently accidentally set together with the
TRUST_TX_LENGTH quirk

Original patch went to stable so this should go there as well.

Fixes: ea0f69d82119 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller")
Cc: stable@vger.kernel.org
cc: Nikolay Martynov 
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20211221112825.54690-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add Telit FN990 compositions

2021-12-22T08:05:14+00:00

commit 2b503c8598d1b232e7fc7526bce9326d92331541 upstream.

Add the following Telit FN990 compositions:

0x1070: tty, adb, rmnet, tty, tty, tty, tty
0x1071: tty, adb, mbim, tty, tty, tty, tty
0x1072: rndis, tty, adb, tty, tty, tty, tty
0x1073: tty, adb, ecm, tty, tty, tty, tty

Signed-off-by: Daniele Palmas 
Link: https://lore.kernel.org/r/20211210100714.22587-1-dnlplm@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: gadget: bRequestType is a bitfield, not a enum

2021-12-22T08:05:14+00:00

[ Upstream commit f08adf5add9a071160c68bb2a61d697f39ab0758 ]

Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value.  Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.

Fix that up by only checking the single bit.

Fixes: 153a2d7e3350 ("USB: gadget: detect too-big endpoint 0 requests")
Cc: Felipe Balbi 
Reported-by: Szymon Heidrich 
Link: https://lore.kernel.org/r/20211214184621.385828-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: core: config: using bit mask instead of individual bits

2021-12-14T09:04:49+00:00

commit ca5737396927afd4d57b133fd2874bbcf3421cdb upstream.

Using standard USB_EP_MAXP_MULT_MASK instead of individual bits for
extracting multiple-transactions bits from wMaxPacketSize value.

Acked-by: Alan Stern 
Signed-off-by: Pavel Hofman 
Link: https://lore.kernel.org/r/20211210085219.16796-2-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman

usb: core: config: fix validation of wMaxPacketValue entries

2021-12-14T09:04:49+00:00

commit 1a3910c80966e4a76b25ce812f6bea0ef1b1d530 upstream.

The checks performed by commit aed9d65ac327 ("USB: validate
wMaxPacketValue entries in endpoint descriptors") require that initial
value of the maxp variable contains both maximum packet size bits
(10..0) and multiple-transactions bits (12..11). However, the existing
code assings only the maximum packet size bits. This patch assigns all
bits of wMaxPacketSize to the variable.

Fixes: aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
Cc: stable 
Acked-by: Alan Stern 
Signed-off-by: Pavel Hofman 
Link: https://lore.kernel.org/r/20211210085219.16796-1-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman

USB: gadget: zero allocate endpoint 0 buffers

2021-12-14T09:04:49+00:00

commit 86ebbc11bb3f60908a51f3e41a17e3f477c2eaa3 upstream.

Under some conditions, USB gadget devices can show allocated buffer
contents to a host.  Fix this up by zero-allocating them so that any
extra data will all just be zeros.

Reported-by: Szymon Heidrich 
Tested-by: Szymon Heidrich 
Signed-off-by: Greg Kroah-Hartman

USB: gadget: detect too-big endpoint 0 requests

2021-12-14T09:04:49+00:00

commit 153a2d7e3350cc89d406ba2d35be8793a64c2038 upstream.

Sometimes USB hosts can ask for buffers that are too large from endpoint
0, which should not be allowed.  If this happens for OUT requests, stall
the endpoint, but for IN requests, trim the request size to the endpoint
buffer size.

Co-developed-by: Szymon Heidrich 
Signed-off-by: Greg Kroah-Hartman

usb: hub: Fix locking issues with address0_mutex

2021-12-08T07:45:02+00:00

commit 6cca13de26eea6d32a98d96d916a048d16a12822 upstream.

Fix the circular lock dependency and unbalanced unlock of addess0_mutex
introduced when fixing an address0_mutex enumeration retry race in commit
ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")

Make sure locking order between port_dev->status_lock and address0_mutex
is correct, and that address0_mutex is not unlocked in hub_port_connect
"done:" codepath which may be reached without locking address0_mutex

Fixes: 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Cc: 
Reported-by: Marek Szyprowski 
Tested-by: Hans de Goede 
Tested-by: Marek Szyprowski 
Acked-by: Hans de Goede 
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20211123101656.1113518-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

usb: hub: Fix usb enumeration issue due to address0 race

2021-12-08T07:45:02+00:00

commit 6ae6dc22d2d1ce6aa77a6da8a761e61aca216f8b upstream.

xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4

The address0_mutex exists to prevent this across both xhci roothubs.

If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.

Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.

Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.

Cc: 
Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel")
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman