linux-stable.git/drivers/usb, branch v4.4.301

usb: hub: Add delay for SuperSpeed hub resume to let links transit to U0

2022-01-27T07:46:17+00:00

[ Upstream commit 00558586382891540c59c9febc671062425a6e47 ]

When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[  281.032951] usb usb2: usb wakeup-resume
[  281.032959] usb usb2: usb auto-resume
[  281.032974] hub 2-0:1.0: hub_resume
[  281.033011] usb usb2-port1: status 0263 change 0000
[  281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.049797] usb 2-1: usb wakeup-resume
[  281.069800] usb 2-1: Waited 0ms for CONNECT
[  281.069810] usb 2-1: finish resume
[  281.070026] hub 2-1:1.0: hub_resume
[  281.070250] usb 2-1-port4: status 0203 change 0000
[  281.070272] usb usb2-port1: resume, status 0
[  281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[  281.089813] usb 2-1.4: usb wakeup-resume
[  281.109792] usb 2-1.4: Waited 0ms for CONNECT
[  281.109801] usb 2-1.4: finish resume
[  281.109991] hub 2-1.4:1.0: hub_resume
[  281.110147] usb 2-1.4-port2: status 0263 change 0000
[  281.110234] usb 2-1-port4: resume, status 0
[  281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[  281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.110426] hub 2-1.4:1.0: hub_suspend
[  281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[  281.130998] hub 2-1:1.0: hub_suspend
[  281.137788] usb 2-1: usb auto-suspend, wakeup 1
[  281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.177828] usb 2-1: usb wakeup-resume
[  281.197839] usb 2-1: Waited 0ms for CONNECT
[  281.197850] usb 2-1: finish resume
[  281.197984] hub 2-1:1.0: hub_resume
[  281.198203] usb 2-1-port4: status 0203 change 0000
[  281.198228] usb usb2-port1: resume, status 0
[  281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[  281.217835] usb 2-1.4: usb wakeup-resume
[  281.237834] usb 2-1.4: Waited 0ms for CONNECT
[  281.237845] usb 2-1.4: finish resume
[  281.237990] hub 2-1.4:1.0: hub_resume
[  281.238067] usb 2-1.4-port2: status 0263 change 0000
[  281.238148] usb 2-1-port4: resume, status 0
[  281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[  281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.238385] hub 2-1.4:1.0: hub_suspend
[  281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[  281.258076] hub 2-1:1.0: hub_suspend
[  281.265744] usb 2-1: usb auto-suspend, wakeup 1
[  281.285976] hub 2-0:1.0: hub_suspend
[  281.285988] usb usb2: bus auto-suspend, wakeup 1

USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.

So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.

Suggested-by: Alan Stern 
Acked-by: Alan Stern 
Signed-off-by: Kai-Heng Feng 
Link: https://lore.kernel.org/r/20211215120108.336597-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: gadget: f_fs: Use stream_open() for endpoint files

2022-01-27T07:46:16+00:00

[ Upstream commit c76ef96fc00eb398c8fc836b0eb2f82bcc619dc7 ]

Function fs endpoint file operations are synchronized via an interruptible
mutex wait. However we see threads that do ep file operations concurrently
are getting blocked for the mutex lock in __fdget_pos(). This is an
uninterruptible wait and we see hung task warnings and kernel panic
if hung_task_panic systcl is enabled if host does not send/receive
the data for long time.

The reason for threads getting blocked in __fdget_pos() is due to
the file position protection introduced by the commit 9c225f2655e3
("vfs: atomic f_pos accesses as per POSIX"). Since function fs
endpoint files does not have the notion of the file position, switch
to the stream mode. This will bypass the file position mutex and
threads will be blocked in interruptible state for the function fs
mutex.

It should not affects user space as we are only changing the task state
changes the task state from UNINTERRUPTIBLE to INTERRUPTIBLE while waiting
for the USB transfers to be finished. However there is a slight change to
the O_NONBLOCK behavior. Earlier threads that are using O_NONBLOCK are also
getting blocked inside fdget_pos(). Now they reach to function fs and error
code is returned. The non blocking behavior is actually honoured now.

Reviewed-by: John Keeping 
Signed-off-by: Pavankumar Kondeti 
Link: https://lore.kernel.org/r/1636712682-1226-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: ftdi-elan: fix memory leak on device disconnect

2022-01-27T07:46:14+00:00

[ Upstream commit 1646566b5e0c556f779180a8514e521ac735de1e ]

'ftdi' is alloced when probe device, but not free on device disconnect,
this cause a memory leak as follows:

unreferenced object 0xffff88800d584000 (size 8400):
  comm "kworker/0:2", pid 3809, jiffies 4295453055 (age 13.784s)
  hex dump (first 32 bytes):
    00 40 58 0d 80 88 ff ff 00 40 58 0d 80 88 ff ff  .@X......@X.....
    00 00 00 00 00 00 00 00 00 00 00 00 ad 4e ad de  .............N..
  backtrace:
    [<000000000d47f947>] kmalloc_order_trace+0x19/0x110 mm/slab_common.c:960
    [<000000008548ac68>] ftdi_elan_probe+0x8c/0x880 drivers/usb/misc/ftdi-elan.c:2647
    [<000000007f73e422>] usb_probe_interface+0x31b/0x800 drivers/usb/core/driver.c:396
    [<00000000fe8d07fc>] really_probe+0x299/0xc30 drivers/base/dd.c:517
    [<0000000005da7d32>] __driver_probe_device+0x357/0x500 drivers/base/dd.c:751
    [<000000003c2c9579>] driver_probe_device+0x4e/0x140 drivers/base/dd.c:781

Fix it by freeing 'ftdi' after nobody use it.

Fixes: a5c66e4b2418 ("USB: ftdi-elan: client driver for ELAN Uxxx adapters")
Reported-by: Hulk Robot 
Signed-off-by: Wei Yongjun 
Link: https://lore.kernel.org/r/20211217083428.2441-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: Fix "slab-out-of-bounds Write" bug in usb_hcd_poll_rh_status

2022-01-27T07:46:12+00:00

commit 1d7d4c07932e04355d6e6528d44a2f2c9e354346 upstream.

When the USB core code for getting root-hub status reports was
originally written, it was assumed that the hub driver would be its
only caller.  But this isn't true now; user programs can use usbfs to
communicate with root hubs and get status reports.  When they do this,
they may use a transfer_buffer that is smaller than the data returned
by the HCD, which will lead to a buffer overflow error when
usb_hcd_poll_rh_status() tries to store the status data.  This was
discovered by syzbot:

BUG: KASAN: slab-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: slab-out-of-bounds in usb_hcd_poll_rh_status+0x5f4/0x780 drivers/usb/core/hcd.c:776
Write of size 2 at addr ffff88801da403c0 by task syz-executor133/4062

This patch fixes the bug by reducing the amount of status data if it
won't fit in the transfer_buffer.  If some data gets discarded then
the URB's completion status is set to -EOVERFLOW rather than 0, to let
the user know what happened.

Reported-and-tested-by: syzbot+3ae6a2b06f131ab9849f@syzkaller.appspotmail.com
Signed-off-by: Alan Stern 
Cc: 
Link: https://lore.kernel.org/r/Yc+3UIQJ2STbxNua@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman

USB: core: Fix bug in resuming hub's handling of wakeup requests

2022-01-27T07:46:12+00:00

commit 0f663729bb4afc92a9986b66131ebd5b8a9254d1 upstream.

Bugzilla #213839 reports a 7-port hub that doesn't work properly when
devices are plugged into some of the ports; the kernel goes into an
unending disconnect/reinitialize loop as shown in the bug report.

This "7-port hub" comprises two four-port hubs with one plugged into
the other; the failures occur when a device is plugged into one of the
downstream hub's ports.  (These hubs have other problems too.  For
example, they bill themselves as USB-2.0 compliant but they only run
at full speed.)

It turns out that the failures are caused by bugs in both the kernel
and the hub.  The hub's bug is that it reports a different
bmAttributes value in its configuration descriptor following a remote
wakeup (0xe0 before, 0xc0 after -- the wakeup-support bit has
changed).

The kernel's bug is inside the hub driver's resume handler.  When
hub_activate() sees that one of the hub's downstream ports got a
wakeup request from a child device, it notes this fact by setting the
corresponding bit in the hub->change_bits variable.  But this variable
is meant for connection changes, not wakeup events; setting it causes
the driver to believe the downstream port has been disconnected and
then connected again (in addition to having received a wakeup
request).

Because of this, the hub driver then tries to check whether the device
currently plugged into the downstream port is the same as the device
that had been attached there before.  Normally this check succeeds and
wakeup handling continues with no harm done (which is why the bug
remained undetected until now).  But with these dodgy hubs, the check
fails because the config descriptor has changed.  This causes the hub
driver to reinitialize the child device, leading to the
disconnect/reinitialize loop described in the bug report.

The proper way to note reception of a downstream wakeup request is
to set a bit in the hub->event_bits variable instead of
hub->change_bits.  That way the hub driver will realize that something
has happened to the port but will not think the port and child device
have been disconnected.  This patch makes that change.

Cc: 
Tested-by: Jonathan McDowell 
Signed-off-by: Alan Stern 
Link: https://lore.kernel.org/r/YdCw7nSfWYPKWQoD@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman

usb: gadget: f_fs: Clear ffs_eventfd in ffs_data_clear.

2022-01-05T11:30:27+00:00

commit b1e0887379422975f237d43d8839b751a6bcf154 upstream.

ffs_data_clear is indirectly called from both ffs_fs_kill_sb and
ffs_ep0_release, so it ends up being called twice when userland closes ep0
and then unmounts f_fs.
If userland provided an eventfd along with function's USB descriptors, it
ends up calling eventfd_ctx_put as many times, causing a refcount
underflow.
NULL-ify ffs_eventfd to prevent these extraneous eventfd_ctx_put calls.

Also, set epfiles to NULL right after de-allocating it, for readability.

For completeness, ffs_data_clear actually ends up being called thrice, the
last call being before the whole ffs structure gets freed, so when this
specific sequence happens there is a second underflow happening (but not
being reported):

/sys/kernel/debug/tracing# modprobe usb_f_fs
/sys/kernel/debug/tracing# echo ffs_data_clear > set_ftrace_filter
/sys/kernel/debug/tracing# echo function > current_tracer
/sys/kernel/debug/tracing# echo 1 > tracing_on
(setup gadget, run and kill function userland process, teardown gadget)
/sys/kernel/debug/tracing# echo 0 > tracing_on
/sys/kernel/debug/tracing# cat trace
 smartcard-openp-436     [000] .....  1946.208786: ffs_data_clear <-ffs_data_closed
 smartcard-openp-431     [000] .....  1946.279147: ffs_data_clear <-ffs_data_closed
 smartcard-openp-431     [000] .n...  1946.905512: ffs_data_clear <-ffs_data_put

Warning output corresponding to above trace:
[ 1946.284139] WARNING: CPU: 0 PID: 431 at lib/refcount.c:28 refcount_warn_saturate+0x110/0x15c
[ 1946.293094] refcount_t: underflow; use-after-free.
[ 1946.298164] Modules linked in: usb_f_ncm(E) u_ether(E) usb_f_fs(E) hci_uart(E) btqca(E) btrtl(E) btbcm(E) btintel(E) bluetooth(E) nls_ascii(E) nls_cp437(E) vfat(E) fat(E) bcm2835_v4l2(CE) bcm2835_mmal_vchiq(CE) videobuf2_vmalloc(E) videobuf2_memops(E) sha512_generic(E) videobuf2_v4l2(E) sha512_arm(E) videobuf2_common(E) videodev(E) cpufreq_dt(E) snd_bcm2835(CE) brcmfmac(E) mc(E) vc4(E) ctr(E) brcmutil(E) snd_soc_core(E) snd_pcm_dmaengine(E) drbg(E) snd_pcm(E) snd_timer(E) snd(E) soundcore(E) drm_kms_helper(E) cec(E) ansi_cprng(E) rc_core(E) syscopyarea(E) raspberrypi_cpufreq(E) sysfillrect(E) sysimgblt(E) cfg80211(E) max17040_battery(OE) raspberrypi_hwmon(E) fb_sys_fops(E) regmap_i2c(E) ecdh_generic(E) rfkill(E) ecc(E) bcm2835_rng(E) rng_core(E) vchiq(CE) leds_gpio(E) libcomposite(E) fuse(E) configfs(E) ip_tables(E) x_tables(E) autofs4(E) ext4(E) crc16(E) mbcache(E) jbd2(E) crc32c_generic(E) sdhci_iproc(E) sdhci_pltfm(E) sdhci(E)
[ 1946.399633] CPU: 0 PID: 431 Comm: smartcard-openp Tainted: G         C OE     5.15.0-1-rpi #1  Debian 5.15.3-1
[ 1946.417950] Hardware name: BCM2835
[ 1946.425442] Backtrace:
[ 1946.432048] [] (dump_backtrace) from [] (show_stack+0x20/0x24)
[ 1946.448226]  r7:00000009 r6:0000001c r5:c04a948c r4:c0a64e2c
[ 1946.458412] [] (show_stack) from [] (dump_stack+0x28/0x30)
[ 1946.470380] [] (dump_stack) from [] (__warn+0xe8/0x154)
[ 1946.482067]  r5:c04a948c r4:c0a71dc8
[ 1946.490184] [] (__warn) from [] (warn_slowpath_fmt+0xa0/0xe4)
[ 1946.506758]  r7:00000009 r6:0000001c r5:c0a71dc8 r4:c0a71e04
[ 1946.517070] [] (warn_slowpath_fmt) from [] (refcount_warn_saturate+0x110/0x15c)
[ 1946.535309]  r8:c0100224 r7:c0dfcb84 r6:ffffffff r5:c3b84c00 r4:c24a17c0
[ 1946.546708] [] (refcount_warn_saturate) from [] (eventfd_ctx_put+0x48/0x74)
[ 1946.564476] [] (eventfd_ctx_put) from [] (ffs_data_clear+0xd0/0x118 [usb_f_fs])
[ 1946.582664]  r5:c3b84c00 r4:c2695b00
[ 1946.590668] [] (ffs_data_clear [usb_f_fs]) from [] (ffs_data_closed+0x9c/0x150 [usb_f_fs])
[ 1946.609608]  r5:bf54d014 r4:c2695b00
[ 1946.617522] [] (ffs_data_closed [usb_f_fs]) from [] (ffs_fs_kill_sb+0x2c/0x30 [usb_f_fs])
[ 1946.636217]  r7:c0dfcb84 r6:c3a12260 r5:bf54d014 r4:c229f000
[ 1946.646273] [] (ffs_fs_kill_sb [usb_f_fs]) from [] (deactivate_locked_super+0x54/0x9c)
[ 1946.664893]  r5:bf54d014 r4:c229f000
[ 1946.672921] [] (deactivate_locked_super) from [] (deactivate_super+0x60/0x64)
[ 1946.690722]  r5:c2a09000 r4:c229f000
[ 1946.698706] [] (deactivate_super) from [] (cleanup_mnt+0xe4/0x14c)
[ 1946.715553]  r5:c2a09000 r4:00000000
[ 1946.723528] [] (cleanup_mnt) from [] (__cleanup_mnt+0x1c/0x20)
[ 1946.739922]  r7:c0dfcb84 r6:c3a12260 r5:c3a126fc r4:00000000
[ 1946.750088] [] (__cleanup_mnt) from [] (task_work_run+0x84/0xb8)
[ 1946.766602] [] (task_work_run) from [] (do_work_pending+0x470/0x56c)
[ 1946.783540]  r7:5ac3c35a r6:c0d0424c r5:c200bfb0 r4:c200a000
[ 1946.793614] [] (do_work_pending) from [] (slow_work_pending+0xc/0x20)
[ 1946.810553] Exception stack(0xc200bfb0 to 0xc200bff8)
[ 1946.820129] bfa0:                                     00000000 00000000 000000aa b5e21430
[ 1946.837104] bfc0: bef867a0 00000001 bef86840 00000034 bef86838 bef86790 bef86794 bef867a0
[ 1946.854125] bfe0: 00000000 bef86798 b67b7a1c b6d626a4 60000010 b5a23760
[ 1946.865335]  r10:00000000 r9:c200a000 r8:c0100224 r7:00000034 r6:bef86840 r5:00000001
[ 1946.881914]  r4:bef867a0
[ 1946.888793] ---[ end trace 7387f2a9725b28d0 ]---

Fixes: 5e33f6fdf735 ("usb: gadget: ffs: add eventfd notification about ffs events")
Cc: stable 
Signed-off-by: Vincent Pelletier 
Link: https://lore.kernel.org/r/f79eeea29f3f98de6782a064ec0f7351ad2f598f.1639793920.git.plr.vincent@gmail.com
Signed-off-by: Greg Kroah-Hartman

xhci: Fresco FL1100 controller should not have BROKEN_MSI quirk set.

2022-01-05T11:30:27+00:00

commit e4844092581ceec22489b66c42edc88bc6079783 upstream.

The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like
other Fresco controllers, but should not have the BROKEN_MSI quirks set.

BROKEN_MSI quirk causes issues in detecting usb drives connected to docks
with this FL1100 controller.
The BROKEN_MSI flag was apparently accidentally set together with the
TRUST_TX_LENGTH quirk

Original patch went to stable so this should go there as well.

Fixes: ea0f69d82119 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller")
Cc: stable@vger.kernel.org
cc: Nikolay Martynov 
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20211221112825.54690-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add Telit FN990 compositions

2021-12-22T08:04:18+00:00

commit 2b503c8598d1b232e7fc7526bce9326d92331541 upstream.

Add the following Telit FN990 compositions:

0x1070: tty, adb, rmnet, tty, tty, tty, tty
0x1071: tty, adb, mbim, tty, tty, tty, tty
0x1072: rndis, tty, adb, tty, tty, tty, tty
0x1073: tty, adb, ecm, tty, tty, tty, tty

Signed-off-by: Daniele Palmas 
Link: https://lore.kernel.org/r/20211210100714.22587-1-dnlplm@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: gadget: bRequestType is a bitfield, not a enum

2021-12-22T08:04:18+00:00

[ Upstream commit f08adf5add9a071160c68bb2a61d697f39ab0758 ]

Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value.  Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.

Fix that up by only checking the single bit.

Fixes: 153a2d7e3350 ("USB: gadget: detect too-big endpoint 0 requests")
Cc: Felipe Balbi 
Reported-by: Szymon Heidrich 
Link: https://lore.kernel.org/r/20211214184621.385828-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: core: config: fix validation of wMaxPacketValue entries

2021-12-14T09:03:50+00:00

commit 1a3910c80966e4a76b25ce812f6bea0ef1b1d530 upstream.

The checks performed by commit aed9d65ac327 ("USB: validate
wMaxPacketValue entries in endpoint descriptors") require that initial
value of the maxp variable contains both maximum packet size bits
(10..0) and multiple-transactions bits (12..11). However, the existing
code assings only the maximum packet size bits. This patch assigns all
bits of wMaxPacketSize to the variable.

Fixes: aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
Cc: stable 
Acked-by: Alan Stern 
Signed-off-by: Pavel Hofman 
Link: https://lore.kernel.org/r/20211210085219.16796-1-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman