linux-stable.git/drivers/usb, branch v4.4.284

Revert "USB: xhci: fix U1/U2 handling for hardware with XHCI_INTEL_HOST quirk set"

2021-09-22T09:41:26+00:00

[ Upstream commit 2847c46c61486fd8bca9136a6e27177212e78c69 ]

This reverts commit 5d5323a6f3625f101dbfa94ba3ef7706cce38760.

That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.

Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2

After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.

Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.

exit latency calculations have been revised since then

Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: gadget: u_ether: fix a potential null pointer dereference

2021-09-22T09:41:24+00:00

[ Upstream commit 8ae01239609b29ec2eff55967c8e0fe3650cfa09 ]

f_ncm tx timeout can call us with null skb to flush
a pending frame.  In this case skb is NULL to begin
with but ceases to be null after dev->wrap() completes.

In such a case in->maxpacket will be read, even though
we've failed to check that 'in' is not NULL.

Though I've never observed this fail in practice,
however the 'flush operation' simply does not make sense with
a null usb IN endpoint - there's nowhere to flush to...
(note that we're the gadget/device, and IN is from the point
 of view of the host, so here IN actually means outbound...)

Cc: Brooke Basile 
Cc: "Bryan O'Donoghue" 
Cc: Felipe Balbi 
Cc: Greg Kroah-Hartman 
Cc: Lorenzo Colitti 
Signed-off-by: Maciej Żenczykowski 
Link: https://lore.kernel.org/r/20210701114834.884597-6-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: host: fotg210: fix the actual_length of an iso packet

2021-09-22T09:41:24+00:00

[ Upstream commit 091cb2f782f32ab68c6f5f326d7868683d3d4875 ]

We should acquire the actual_length of an iso packet
from the iTD directly using FOTG210_ITD_LENGTH() macro.

Signed-off-by: Kelly Devilliv 
Link: https://lore.kernel.org/r/20210627125747.127646-4-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: ehci-orion: Handle errors of clk_prepare_enable() in probe

2021-09-22T09:41:22+00:00

[ Upstream commit 4720f1bf4ee4a784d9ece05420ba33c9222a3004 ]

ehci_orion_drv_probe() did not account for possible errors of
clk_prepare_enable() that in particular could cause invocation of
clk_disable_unprepare() on clocks that were not prepared/enabled yet,
e.g. in remove or on handling errors of usb_add_hcd() in probe. Though,
there were several patches fixing different issues with clocks in this
driver, they did not solve this problem.

Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe()
to avoid calls of clk_disable_unprepare() without previous successful
invocation of clk_prepare_enable().

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 8c869edaee07 ("ARM: Orion: EHCI: Add support for enabling clocks")
Co-developed-by: Kirill Shilimanov 
Reviewed-by: Andrew Lunn 
Acked-by: Alan Stern 
Signed-off-by: Evgeny Novikov 
Signed-off-by: Kirill Shilimanov 
Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: gadget: mv_u3d: request_irq() after initializing UDC

2021-09-22T09:41:21+00:00

[ Upstream commit 2af0c5ffadaf9d13eca28409d4238b4e672942d3 ]

If IRQ occurs between calling  request_irq() and  mv_u3d_eps_init(),
then null pointer dereference occurs since u3d->eps[] wasn't
initialized yet but used in mv_u3d_nuke().

The patch puts registration of the interrupt handler after
initializing of neccesery data.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 90fccb529d24 ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Acked-by: Felipe Balbi 
Signed-off-by: Nadezda Lutovinova 
Link: https://lore.kernel.org/r/20210818141247.4794-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: phy: tahvo: add IRQ check

2021-09-22T09:41:21+00:00

[ Upstream commit 0d45a1373e669880b8beaecc8765f44cb0241e47 ]

The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding an
original error code.  Stop calling request_threaded_irq() with the invalid
IRQ #s.

Fixes: 9ba96ae5074c ("usb: omap1: Tahvo USB transceiver driver")
Acked-by: Felipe Balbi 
Signed-off-by: Sergey Shtylyov 
Link: https://lore.kernel.org/r/8280d6a4-8e9a-7cfe-1aa9-db586dc9afdf@omp.ru
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: host: ohci-tmio: add IRQ check

2021-09-22T09:41:21+00:00

[ Upstream commit 4ac5132e8a4300637a2da8f5d6bc7650db735b8a ]

The driver neglects to check the  result of platform_get_irq()'s call and
blithely passes the negative error codes to usb_add_hcd() (which takes
*unsigned* IRQ #), causing request_irq() that it calls to fail with
-EINVAL, overriding an original error code. Stop calling usb_add_hcd()
with the invalid IRQ #s.

Fixes: 78c73414f4f6 ("USB: ohci: add support for tmio-ohci cell")
Acked-by: Alan Stern 
Signed-off-by: Sergey Shtylyov 
Link: https://lore.kernel.org/r/402e1a45-a0a4-0e08-566a-7ca1331506b1@omp.ru
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: phy: twl6030: add IRQ checks

2021-09-22T09:41:21+00:00

[ Upstream commit 0881e22c06e66af0b64773c91c8868ead3d01aa1 ]

The driver neglects to check the result of platform_get_irq()'s calls and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing them both to fail with -EINVAL, overriding
an original error code.  Stop calling request_threaded_irq() with the
invalid IRQ #s.

Fixes: c33fad0c3748 ("usb: otg: Adding twl6030-usb transceiver driver for OMAP4430")
Acked-by: Felipe Balbi 
Signed-off-by: Sergey Shtylyov 
Link: https://lore.kernel.org/r/9507f50b-50f1-6dc4-f57c-3ed4e53a1c25@omp.ru
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: phy: fsl-usb: add IRQ check

2021-09-22T09:41:21+00:00

[ Upstream commit ecc2f30dbb25969908115c81ec23650ed982b004 ]

The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling request_irq() with the invalid IRQ #s.

Fixes: 0807c500a1a6 ("USB: add Freescale USB OTG Transceiver driver")
Acked-by: Felipe Balbi 
Signed-off-by: Sergey Shtylyov 
Link: https://lore.kernel.org/r/b0a86089-8b8b-122e-fd6d-73e8c2304964@omp.ru
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: gadget: udc: at91: add IRQ check

2021-09-22T09:41:20+00:00

[ Upstream commit 50855c31573b02963f0aa2aacfd4ea41c31ae0e0 ]

The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling devm_request_irq() with the invalid IRQ #s.

Fixes: 8b2e76687b39 ("USB: AT91 UDC updates, mostly power management")
Signed-off-by: Sergey Shtylyov 
Acked-by: Felipe Balbi 
Link: https://lore.kernel.org/r/6654a224-739a-1a80-12f0-76d920f87b6c@omp.ru
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin