linux-stable.git/drivers/usb, branch v4.4.217

usb: core: port: do error out if usb_autopm_get_interface() fails

2020-03-11T06:51:17+00:00

commit 1f8b39bc99a31759e97a0428a5c3f64802c1e61d upstream.

Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:

On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
 > A revised search finds line 997 in drivers/usb/core/hub.c and lines
 > 216, 269 in drivers/usb/core/port.c.  (I didn't try looking in any
 > other directories.)  AFAICT all three of these should check the
 > return value, although a error message in the kernel log probably
 > isn't needed.

Factor out the usb_port_runtime_{resume,suspend}() changes into a
standalone patch to allow conflict-free porting on top of stable v3.9+.

[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org

Fixes: 971fcd492cebf5 ("usb: add runtime pm support for usb port device")
Cc: stable@vger.kernel.org # v3.9+
Suggested-by: Alan Stern 
Signed-off-by: Eugeniu Rosca 
Acked-by: Alan Stern 
Link: https://lore.kernel.org/r/20200226175036.14946-3-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman

usb: core: hub: do error out if usb_autopm_get_interface() fails

2020-03-11T06:51:17+00:00

commit 60e3f6e4ac5b0fda43dad01c32e09409ec710045 upstream.

Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:

On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
 > A revised search finds line 997 in drivers/usb/core/hub.c and lines
 > 216, 269 in drivers/usb/core/port.c.  (I didn't try looking in any
 > other directories.)  AFAICT all three of these should check the
 > return value, although a error message in the kernel log probably
 > isn't needed.

Factor out the usb_remove_device() change into a standalone patch to
allow conflict-free integration on top of the earliest stable branches.

[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org

Fixes: 253e05724f9230 ("USB: add a "remove hardware" sysfs attribute")
Cc: stable@vger.kernel.org # v2.6.33+
Suggested-by: Alan Stern 
Signed-off-by: Eugeniu Rosca 
Acked-by: Alan Stern 
Link: https://lore.kernel.org/r/20200226175036.14946-2-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman

usb: quirks: add NO_LPM quirk for Logitech Screen Share

2020-03-11T06:51:17+00:00

commit b96ed52d781a2026d0c0daa5787c6f3d45415862 upstream.

LPM on the device appears to cause xHCI host controllers to claim
that there isn't enough bandwidth to support additional devices.

Signed-off-by: Dan Lazewatsky 
Cc: stable 
Signed-off-by: Gustavo Padovan 
Link: https://lore.kernel.org/r/20200226143438.1445-1-gustavo.padovan@collabora.com
Signed-off-by: Greg Kroah-Hartman

usb: storage: Add quirk for Samsung Fit flash

2020-03-11T06:51:17+00:00

commit 86d92f5465958752481269348d474414dccb1552 upstream.

Current driver has 240 (USB2.0) and 2048 (USB3.0) as max_sectors,
e.g., /sys/bus/scsi/devices/0:0:0:0/max_sectors

If data access times out, driver error handling will issue a port
reset.
Sometimes Samsung Fit (090C:1000) flash disk will not respond to
later Set Address or Get Descriptor command.

Adding this quirk to limit max_sectors to 64 sectors to avoid issue
occurring.

Signed-off-by: Jim Lin 
Acked-by: Alan Stern 
Cc: stable 
Link: https://lore.kernel.org/r/1583158895-31342-1-git-send-email-jilin@nvidia.com
Signed-off-by: Greg Kroah-Hartman

usb: gadget: serial: fix Tx stall after buffer overflow

2020-03-11T06:51:16+00:00

[ Upstream commit e4bfded56cf39b8d02733c1e6ef546b97961e18a ]

Symptom: application opens /dev/ttyGS0 and starts sending (writing) to
it while either USB cable is not connected, or nobody listens on the
other side of the cable. If driver circular buffer overflows before
connection is established, no data will be written to the USB layer
until/unless /dev/ttyGS0 is closed and re-opened again by the
application (the latter besides having no means of being notified about
the event of establishing of the connection.)

Fix: on open and/or connect, kick Tx to flush circular buffer data to
USB layer.

Signed-off-by: Sergey Organov 
Reviewed-by: Michał Mirosław 
Signed-off-by: Felipe Balbi 
Signed-off-by: Sasha Levin

usb: gadget: ffs: ffs_aio_cancel(): Save/restore IRQ flags

2020-03-11T06:51:16+00:00

[ Upstream commit 43d565727a3a6fd24e37c7c2116475106af71806 ]

ffs_aio_cancel() can be called from both interrupt and thread context. Make
sure that the current IRQ state is saved and restored by using
spin_{un,}lock_irq{save,restore}().

Otherwise undefined behavior might occur.

Acked-by: Michal Nazarewicz 
Signed-off-by: Lars-Peter Clausen 
Signed-off-by: Alexandru Ardelean 
Signed-off-by: Felipe Balbi 
Signed-off-by: Sasha Levin

xhci: apply XHCI_PME_STUCK_QUIRK to Intel Comet Lake platforms

2020-02-28T14:39:14+00:00

commit a3ae87dce3a5abe0b57c811bab02b2564b574106 upstream.

Intel Comet Lake based platform require the XHCI_PME_STUCK_QUIRK
quirk as well. Without this xHC can not enter D3 in runtime suspend.

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20200210134553.9144-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

USB: hub: Don't record a connect-change event during reset-resume

2020-02-28T14:39:12+00:00

commit 8099f58f1ecddf4f374f4828a3dff8397c7cbd74 upstream.

Paul Zimmerman reports that his USB Bluetooth adapter sometimes
crashes following system resume, when it receives a
Get-Device-Descriptor request while it is busy doing something else.

Such a request was added by commit a4f55d8b8c14 ("usb: hub: Check
device descriptor before resusciation"). It gets sent when the hub
driver's work thread checks whether a connect-change event on an
enabled port really indicates a new device has been connected, as
opposed to an old device momentarily disconnecting and then
reconnecting (which can happen with xHCI host controllers, since they
automatically enable connected ports).

The same kind of thing occurs when a port's power session is lost
during system suspend. When the system wakes up it sees a
connect-change event on the port, and if the child device's
persist_enabled flag was set then hub_activate() sets the device's
reset_resume flag as well as the port's bit in hub->change_bits. The
reset-resume code then takes responsibility for checking that the same
device is still attached to the port, and it does this as part of the
device's resume pathway. By the time the hub driver's work thread
starts up again, the device has already been fully reinitialized and
is busy doing its own thing. There's no need for the work thread to
do the same check a second time, and in fact this unnecessary check is
what caused the problem that Paul observed.

Note that performing the unnecessary check is not actually a bug.
Devices are supposed to be able to send descriptors back to the host
even when they are busy doing something else. The underlying cause of
Paul's problem lies in his Bluetooth adapter. Nevertheless, we
shouldn't perform the same check twice in a row -- and as a nice side
benefit, removing the extra check allows the Bluetooth adapter to work
more reliably.

The work thread performs its check when it sees that the port's bit is
set in hub->change_bits. In this situation that bit is interpreted as
though a connect-change event had occurred on the port _after_ the
reset-resume, which is not what actually happened.

One possible fix would be to make the reset-resume code clear the
port's bit in hub->change_bits. But it seems simpler to just avoid
setting the bit during hub_activate() in the first place. That's what
this patch does.

(Proving that the patch is correct when CONFIG_PM is disabled requires
a little thought. In that setting hub_activate() will be called only
for initialization and resets, since there won't be any resumes or
reset-resumes. During initialization and hub resets the hub doesn't
have any child devices, and so this code path never gets executed.)

Reported-and-tested-by: Paul Zimmerman
Signed-off-by: Alan Stern
Link: https://marc.info/?t=157949360700001&r=1&w=2
CC: David Heinzelmann
CC:
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001311037460.1577-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman

USB: Fix novation SourceControl XL after suspend

2020-02-28T14:39:12+00:00

commit b692056db8ecc7f452b934f016c17348282b7699 upstream.

Currently, the SourceControl will stay in power-down mode after resuming
from suspend. This patch resets the device after suspend to power it up.

Signed-off-by: Richard Dodd 
Cc: stable 
Link: https://lore.kernel.org/r/20200212142220.36892-1-richard.o.dodd@gmail.com
Signed-off-by: Greg Kroah-Hartman

usb: uas: fix a plug & unplug racing

2020-02-28T14:39:12+00:00

commit 3e99862c05a9caa5a27969f41566b428696f5a9a upstream.

When a uas disk is plugged into an external hub, uas_probe()
will be called by the hub thread to do the probe. It will
first create a SCSI host and then do the scan for this host.
During the scan, it will probe the LUN using SCSI INQUERY command
which will be packed in the URB and submitted to uas disk.

There might be a chance that this external hub with uas disk
attached is unplugged during the scan. In this case, uas driver
will fail to submit the URB (due to the NOTATTACHED state of uas
device) and try to put this SCSI command back to request queue
waiting for next chance to run.

In normal case, this cycle will terminate when hub thread gets
disconnection event and calls into uas_disconnect() accordingly.
But in this case, uas_disconnect() will not be called because
hub thread of external hub gets stuck waiting for the completion
of this SCSI command. A deadlock happened.

In this fix, uas will call scsi_scan_host() asynchronously to
avoid the blocking of hub thread.

Signed-off-by: EJ Hsu 
Acked-by: Oliver Neukum 
Cc: stable 
Link: https://lore.kernel.org/r/20200130092506.102760-1-ejh@nvidia.com
Signed-off-by: Greg Kroah-Hartman