linux-stable.git/drivers/usb, branch v4.4.181

USB: rio500: fix memory leak in close after disconnect

2019-06-11T10:24:09+00:00

commit e0feb73428b69322dd5caae90b0207de369b5575 upstream.

If a disconnected device is closed, rio_close() must free
the buffers.

Signed-off-by: Oliver Neukum 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: rio500: refuse more than one device at a time

2019-06-11T10:24:09+00:00

commit 3864d33943b4a76c6e64616280e98d2410b1190f upstream.

This driver is using a global variable. It cannot handle more than
one device at a time. The issue has been existing since the dawn
of the driver.

Signed-off-by: Oliver Neukum 
Reported-by: syzbot+35f04d136fc975a70da4@syzkaller.appspotmail.com
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: Add LPM quirk for Surface Dock GigE adapter

2019-06-11T10:24:08+00:00

commit ea261113385ac0a71c2838185f39e8452d54b152 upstream.

Without USB_QUIRK_NO_LPM ethernet will not work and rtl8152 will
complain with

    r8152 : Stop submitting intr, status -71

Adding the quirk resolves this. As the dock is externally powered, this
should not have any drawbacks.

Signed-off-by: Maximilian Luz 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: sisusbvga: fix oops in error path of sisusb_probe

2019-06-11T10:24:08+00:00

commit 9a5729f68d3a82786aea110b1bfe610be318f80a upstream.

The pointer used to log a failure of usb_register_dev() must
be set before the error is logged.

v2: fix that minor is not available before registration

Signed-off-by: oliver Neukum 
Reported-by: syzbot+a0cbdbd6d169020c8959@syzkaller.appspotmail.com
Fixes: 7b5cd5fefbe02 ("USB: SisUSB2VGA: Convert printk to dev_* macros")
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: Fix slab-out-of-bounds write in usb_get_bos_descriptor

2019-06-11T10:24:08+00:00

commit a03ff54460817c76105f81f3aa8ef655759ccc9a upstream.

The syzkaller USB fuzzer found a slab-out-of-bounds write bug in the
USB core, caused by a failure to check the actual size of a BOS
descriptor.  This patch adds a check to make sure the descriptor is at
least as large as it is supposed to be, so that the code doesn't
inadvertently access memory beyond the end of the allocated region
when assigning to dev->bos->desc->bNumDeviceCaps later on.

Signed-off-by: Alan Stern 
Reported-and-tested-by: syzbot+71f1e64501a309fcc012@syzkaller.appspotmail.com
CC: 
Signed-off-by: Greg Kroah-Hartman

usb: xhci: avoid null pointer deref when bos field is NULL

2019-06-11T10:24:08+00:00

commit 7aa1bb2ffd84d6b9b5f546b079bb15cd0ab6e76e upstream.

With defective USB sticks we see the following error happen:
usb 1-3: new high-speed USB device number 6 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: device descriptor read/64, error -71
usb 1-3: new high-speed USB device number 7 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: unable to get BOS descriptor set
usb 1-3: New USB device found, idVendor=0781, idProduct=5581
usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
...
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008

This comes from the following place:
[ 1660.215380] IP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd]
[ 1660.222092] PGD 0 P4D 0
[ 1660.224918] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 1660.425520] CPU: 1 PID: 38 Comm: kworker/1:1 Tainted: P     U  W  O    4.14.67-apl #1
[ 1660.434277] Workqueue: usb_hub_wq hub_event [usbcore]
[ 1660.439918] task: ffffa295b6ae4c80 task.stack: ffffad4580150000
[ 1660.446532] RIP: 0010:xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd]
[ 1660.453821] RSP: 0018:ffffad4580153c70 EFLAGS: 00010046
[ 1660.459655] RAX: 0000000000000000 RBX: ffffa295b4d7c000 RCX: 0000000000000002
[ 1660.467625] RDX: 0000000000000002 RSI: ffffffff984a55b2 RDI: ffffffff984a55b2
[ 1660.475586] RBP: ffffad4580153cc8 R08: 0000000000d6520a R09: 0000000000000001
[ 1660.483556] R10: ffffad4580a004a0 R11: 0000000000000286 R12: ffffa295b4d7c000
[ 1660.491525] R13: 0000000000010648 R14: ffffa295a84e1800 R15: 0000000000000000
[ 1660.499494] FS:  0000000000000000(0000) GS:ffffa295bfc80000(0000) knlGS:0000000000000000
[ 1660.508530] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1660.514947] CR2: 0000000000000008 CR3: 000000025a114000 CR4: 00000000003406a0
[ 1660.522917] Call Trace:
[ 1660.525657]  usb_set_usb2_hardware_lpm+0x3d/0x70 [usbcore]
[ 1660.531792]  usb_disable_device+0x242/0x260 [usbcore]
[ 1660.537439]  usb_disconnect+0xc1/0x2b0 [usbcore]
[ 1660.542600]  hub_event+0x596/0x18f0 [usbcore]
[ 1660.547467]  ? trace_preempt_on+0xdf/0x100
[ 1660.552040]  ? process_one_work+0x1c1/0x410
[ 1660.556708]  process_one_work+0x1d2/0x410
[ 1660.561184]  ? preempt_count_add.part.3+0x21/0x60
[ 1660.566436]  worker_thread+0x2d/0x3f0
[ 1660.570522]  kthread+0x122/0x140
[ 1660.574123]  ? process_one_work+0x410/0x410
[ 1660.578792]  ? kthread_create_on_node+0x60/0x60
[ 1660.583849]  ret_from_fork+0x3a/0x50
[ 1660.587839] Code: 00 49 89 c3 49 8b 84 24 50 16 00 00 8d 4a ff 48 8d 04 c8 48 89 ca 4c 8b 10 45 8b 6a 04 48 8b 00 48 89 45 c0 49 8b 86 80 03 00 00 <48> 8b 40 08 8b 40 03 0f 1f 44 00 00 45 85 ff 0f 84 81 01 00 00
[ 1660.608980] RIP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] RSP: ffffad4580153c70
[ 1660.617921] CR2: 0000000000000008

Tracking this down shows that udev->bos is NULL in the following code:
(xhci.c, in xhci_set_usb2_hardware_lpm)
	field = le32_to_cpu(udev->bos->ext_cap->bmAttributes);  <<<<<<< here

	xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n",
			enable ? "enable" : "disable", port_num + 1);

	if (enable) {
		/* Host supports BESL timeout instead of HIRD */
		if (udev->usb2_hw_lpm_besl_capable) {
			/* if device doesn't have a preferred BESL value use a
			 * default one which works with mixed HIRD and BESL
			 * systems. See XHCI_DEFAULT_BESL definition in xhci.h
			 */
			if ((field & USB_BESL_SUPPORT) &&
			    (field & USB_BESL_BASELINE_VALID))
				hird = USB_GET_BESL_BASELINE(field);
			else
				hird = udev->l1_params.besl;

The failing case is when disabling LPM. So it is sufficient to avoid
access to udev->bos by moving the instruction into the "enable" clause.

Cc: Stable 
Signed-off-by: Carsten Schmid 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()

2019-06-11T10:24:08+00:00

commit f7fac17ca925faa03fc5eb854c081a24075f8bad upstream.

Xhci_handshake() implements the algorithm already captured by
readl_poll_timeout_atomic(). Convert the former to use the latter to
avoid repetition.

Turned out this patch also fixes a bug on the AMD Stoneyridge platform
where usleep(1) sometimes takes over 10ms.
This means a 5 second timeout can easily take over 15 seconds which will
trigger the watchdog and reboot the system.

[Add info about patch fixing a bug to commit message -Mathias]
Signed-off-by: Andrey Smirnov 
Tested-by: Raul E Rangel 
Reviewed-by: Raul E Rangel 
Cc: 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb: core: Add PM runtime calls to usb_hcd_platform_shutdown

2019-06-11T10:24:05+00:00

[ Upstream commit 8ead7e817224d7832fe51a19783cb8fcadc79467 ]

If ohci-platform is runtime suspended, we can currently get an "imprecise
external abort" on reboot with ohci-platform loaded when PM runtime
is implemented for the SoC.

Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown.

Signed-off-by: Tony Lindgren 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: core: Don't unbind interfaces following device reset failure

2019-06-11T10:23:58+00:00

[ Upstream commit 381419fa720060ba48b7bbc483be787d5b1dca6f ]

The SCSI core does not like to have devices or hosts unregistered
while error recovery is in progress.  Trying to do so can lead to
self-deadlock: Part of the removal code tries to obtain a lock already
held by the error handler.

This can cause problems for the usb-storage and uas drivers, because
their error handler routines perform a USB reset, and if the reset
fails then the USB core automatically goes on to unbind all drivers
from the device's interfaces -- all while still in the context of the
SCSI error handler.

As it turns out, practically all the scenarios leading to a USB reset
failure end up causing a device disconnect (the main error pathway in
usb_reset_and_verify_device(), at the end of the routine, calls
hub_port_logical_disconnect() before returning).  As a result, the
hub_wq thread will soon become aware of the problem and will unbind
all the device's drivers in its own context, not in the
error-handler's context.

This means that usb_reset_device() does not need to call
usb_unbind_and_rebind_marked_interfaces() in cases where
usb_reset_and_verify_device() has returned an error, because hub_wq
will take care of everything anyway.

This particular problem was observed in somewhat artificial
circumstances, by using usbfs to tell a hub to power-down a port
connected to a USB-3 mass storage device using the UAS protocol.  With
the port turned off, the currently executing command timed out and the
error handler started running.  The USB reset naturally failed,
because the hub port was off, and the error handler deadlocked as
described above.  Not carrying out the call to
usb_unbind_and_rebind_marked_interfaces() fixes this issue.

Signed-off-by: Alan Stern 
Reported-by: Kento Kobayashi 
Tested-by: Kento Kobayashi 
CC: Bart Van Assche 
CC: Martin K. Petersen 
CC: Jacky Cao 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: serial: fix unthrottle races

2019-05-16T17:45:16+00:00

[ Upstream commit 3f5edd58d040bfa4b74fb89bc02f0bc6b9cd06ab ]

Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().

First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.

	CPU 1				CPU 2
	================		================
	complete()			unthrottle()
	  process_urb();
	  smp_mb__before_atomic();
	  set_bit(i, free);		  if (test_and_clear_bit(i, free))
	  					  submit_urb();

Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.

	CPU 1				CPU 2
	================		================
	complete()			unthrottle()
	  set_bit(i, free);		  throttled = 0;
	  smp_mb__after_atomic();	  smp_mb();
	  if (throttled)		  if (test_and_clear_bit(i, free))
	  	  return;			  submit_urb();

Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.

Fixes: d83b405383c9 ("USB: serial: add support for multiple read urbs")
Signed-off-by: Johan Hovold 
Signed-off-by: Sasha Levin