linux-stable.git/drivers/usb, branch v4.19.37

usb: dwc3: gadget: Fix OTG events when gadget driver isn't loaded

2019-04-05T20:33:13+00:00

[ Upstream commit 169e3b68cadb5775daca009ced4faf01ffd97dcf ]

On v3.10a in dual-role mode, if port is in device mode
and gadget driver isn't loaded, the OTG event interrupts don't
come through.

It seems that if the core is configured to be OTG2.0 only,
then we can't leave the DCFG.DEVSPD at Super-speed (default)
if we expect OTG to work properly. It must be set to High-speed.

Fix this issue by configuring DCFG.DEVSPD to the supported
maximum speed at gadget init. Device tree still needs to provide
correct supported maximum speed for this to work.

This issue wasn't present on v2.40a but is seen on v3.10a.
It doesn't cause any side effects on v2.40a.

Signed-off-by: Roger Quadros 
Signed-off-by: Sekhar Nori 
Signed-off-by: Felipe Balbi 
Signed-off-by: Sasha Levin

usb: f_fs: Avoid crash due to out-of-scope stack ptr access

2019-04-05T20:33:08+00:00

[ Upstream commit 54f64d5c983f939901dacc8cfc0983727c5c742e ]

Since the 5.0 merge window opened, I've been seeing frequent
crashes on suspend and reboot with the trace:

[   36.911170] Unable to handle kernel paging request at virtual address ffffff801153d660
[   36.912769] Unable to handle kernel paging request at virtual address ffffff800004b564
...
[   36.950666] Call trace:
[   36.950670]  queued_spin_lock_slowpath+0x1cc/0x2c8
[   36.950681]  _raw_spin_lock_irqsave+0x64/0x78
[   36.950692]  complete+0x28/0x70
[   36.950703]  ffs_epfile_io_complete+0x3c/0x50
[   36.950713]  usb_gadget_giveback_request+0x34/0x108
[   36.950721]  dwc3_gadget_giveback+0x50/0x68
[   36.950723]  dwc3_thread_interrupt+0x358/0x1488
[   36.950731]  irq_thread_fn+0x30/0x88
[   36.950734]  irq_thread+0x114/0x1b0
[   36.950739]  kthread+0x104/0x130
[   36.950747]  ret_from_fork+0x10/0x1c

I isolated this down to in ffs_epfile_io():
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/usb/gadget/function/f_fs.c#n1065

Where the completion done is setup on the stack:
  DECLARE_COMPLETION_ONSTACK(done);

Then later we setup a request and queue it, and wait for it:
  if (unlikely(wait_for_completion_interruptible(&done))) {
    /*
    * To avoid race condition with ffs_epfile_io_complete,
    * dequeue the request first then check
    * status. usb_ep_dequeue API should guarantee no race
    * condition with req->complete callback.
    */
    usb_ep_dequeue(ep->ep, req);
    interrupted = ep->status < 0;
  }

The problem is, that we end up being interrupted, dequeue the
request, and exit.

But then the irq triggers and we try calling complete() on the
context pointer which points to now random stack space, which
results in the panic.

Alan Stern pointed out there is a bug here, in that the snippet
above "assumes that usb_ep_dequeue() waits until the request has
been completed." And that:

    wait_for_completion(&done);

Is needed right after the usb_ep_dequeue().

Thus this patch implements that change. With it I no longer see
the crashes on suspend or reboot.

This issue seems to have been uncovered by behavioral changes in
the dwc3 driver in commit fec9095bdef4e ("usb: dwc3: gadget:
remove wait_end_transfer").

Cc: Alan Stern 
Cc: Felipe Balbi 
Cc: Zeng Tao 
Cc: Jack Pham 
Cc: Thinh Nguyen 
Cc: Chen Yu 
Cc: Jerry Zhang 
Cc: Lars-Peter Clausen 
Cc: Vincent Pelletier 
Cc: Andrzej Pietrasiewicz 
Cc: Greg Kroah-Hartman 
Cc: Linux USB List 
Suggested-by: Alan Stern 
Signed-off-by: John Stultz 
Signed-off-by: Felipe Balbi 
Signed-off-by: Sasha Levin

usb: chipidea: Grab the (legacy) USB PHY by phandle first

2019-04-05T20:33:01+00:00

[ Upstream commit 68ef236274793066b9ba3154b16c0acc1c891e5c ]

According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.

This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.

Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.

When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.

Signed-off-by: Paul Kocialkowski 
Signed-off-by: Peter Chen 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: typec: class: Don't use port parent for getting mux handles

2019-04-03T04:26:30+00:00

commit 23481121c81d984193edf1532f5e123637e50903 upstream.

It is not possible to use the parent of the port device when
requesting mux handles as the parent may be a multiport USB
Type-C or PD controller. The muxes must be assigned to the
ports, not the controllers.

This will also move the requesting of the muxes after the
port device is initialized.

Acked-by: Hans de Goede 
Tested-by: Hans de Goede 
Signed-off-by: Heikki Krogerus 
Signed-off-by: Greg Kroah-Hartman

usb: cdc-acm: fix race during wakeup blocking TX traffic

2019-04-03T04:26:28+00:00

commit 93e1c8a638308980309e009cc40b5a57ef87caf1 upstream.

When the kernel is compiled with preemption enabled, the URB completion
handler can run in parallel with the work responsible for waking up the
tty layer. If the URB handler sets the EVENT_TTY_WAKEUP bit during the
call to tty_port_tty_wakeup() to signal that there is room for additional
input, it will be cleared at the end of this call. As a result, TX traffic
on the upper layer will be blocked.

This can be seen with a kernel configured with CONFIG_PREEMPT, and a fast
modem connected with PPP running over a USB CDC-ACM port.

Use test_and_clear_bit() instead, which ensures that each wakeup requested
by the URB completion code will trigger a call to tty_port_tty_wakeup().

Fixes: 1aba579f3cf5 cdc-acm: handle read pipe errors
Signed-off-by: Romain Izard 
Cc: stable 
Acked-by: Oliver Neukum 
Signed-off-by: Greg Kroah-Hartman

xhci: Don't let USB3 ports stuck in polling state prevent suspend

2019-04-03T04:26:28+00:00

commit d92f2c59cc2cbca6bfb2cc54882b58ba76b15fd4 upstream.

Commit 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.

Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.

Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).

Original patch was sent to stable, this one should go there as well

Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb: xhci: dbc: Don't free all memory with spinlock held

2019-04-03T04:26:27+00:00

commit 8867ea262196a6945c24a0fb739575af646ec0e9 upstream.

The xhci debug capability (DbC) feature did its memory cleanup with
spinlock held. dma_free_coherent() warns if called with interrupts
disabled

move the memory cleanup outside the spinlock

Cc: stable 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

xhci: Fix port resume done detection for SS ports with LPM enabled

2019-04-03T04:26:27+00:00

commit 6cbcf596934c8e16d6288c7cc62dfb7ad8eadf15 upstream.

A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.

Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.

Add U1 and U2 to the possible link states when checking for finished
port resume.

Cc: stable 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb: host: xhci-rcar: Add XHCI_TRUST_TX_LENGTH quirk

2019-04-03T04:26:27+00:00

commit 40fc165304f0faaae78b761f8ee30b5d216b1850 upstream.

When plugging BUFFALO LUA4-U3-AGT USB3.0 to Gigabit Ethernet LAN
Adapter, warning messages filled up dmesg.

[  101.098287] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[  101.117463] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[  101.136513] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?

Adding the XHCI_TRUST_TX_LENGTH quirk resolves the issue.

Signed-off-by: Yasushi Asano 
Signed-off-by: Spyridon Papageorgiou 
Acked-by: Yoshihiro Shimoda 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usb: common: Consider only available nodes for dr_mode

2019-04-03T04:26:27+00:00

commit 238e0268c82789e4c107a37045d529a6dbce51a9 upstream.

There are cases where multiple device tree nodes point to the
same phy node by means of the "phys" property, but we should
only consider those nodes that are marked as available rather
than just any node.

Fixes: 98bfb3946695 ("usb: of: add an api to get dr_mode by the phy node")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Fabrizio Castro 
Signed-off-by: Greg Kroah-Hartman