linux-stable.git/drivers/usb, branch v4.14.65

usb: gadget: udc: renesas_usb3: should remove debugfs

2018-08-03T05:50:43+00:00

commit 1990cf7c21ea185cec98c6d45a82c04481261e35 upstream.

This patch fixes an issue that this driver doesn't remove its debugfs.

Fixes: 43ba968b00ea ("usb: gadget: udc: renesas_usb3: add debugfs to set the b-device mode")
Cc:  # v4.14+
Signed-off-by: Yoshihiro Shimoda 
Reviewed-by: Simon Horman 
Signed-off-by: Felipe Balbi 
Signed-off-by: Sudip Mukherjee 
Signed-off-by: Greg Kroah-Hartman

usb: hub: Don't wait for connect state at resume for powered-off ports

2018-08-03T05:50:40+00:00

[ Upstream commit 5d111f5190848d6fb1c414dc57797efea3526a2f ]

wait_for_connected() wait till a port change status to
USB_PORT_STAT_CONNECTION, but this is not possible if
the port is unpowered. The loop will only exit at timeout.

Such case take place if an over-current incident happen
while system is in S3. Then during resume wait_for_connected()
will wait 2s, which may be noticeable by the user.

Signed-off-by: Dominik Bozek 
Signed-off-by: Kuppuswamy Sathyanarayanan 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

usb: gadget: f_fs: Only return delayed status when len is 0

2018-07-28T05:55:44+00:00

commit 4d644abf25698362bd33d17c9ddc8f7122c30f17 upstream.

Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.

It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.

This manifests as the following bugs:

Prior to 946ef68ad4e4 ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.

After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.

Fixes: 946ef68ad4e4 ("Let setup() return USB_GADGET_DELAYED_STATUS")
Signed-off-by: Jerry Zhang 
Cc: stable 
Acked-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: Fix DMA alignment to start at allocated boundary

2018-07-28T05:55:44+00:00

commit 56406e017a883b54b339207b230f85599f4d70ae upstream.

The commit 3bc04e28a030 ("usb: dwc2: host: Get aligned DMA in a more
supported way") introduced a common way to align DMA allocations.
The code in the commit aligns the struct dma_aligned_buffer but the
actual DMA address pointed by data[0] gets aligned to an offset from
the allocated boundary by the kmalloc_ptr and the old_xfer_buffer
pointers.

This is against the recommendation in Documentation/DMA-API.txt which
states:

  Therefore, it is recommended that driver writers who don't take
  special care to determine the cache line size at run time only map
  virtual regions that begin and end on page boundaries (which are
  guaranteed also to be cache line boundaries).

The effect of this is that architectures with non-coherent DMA caches
may run into memory corruption or kernel crashes with Unhandled
kernel unaligned accesses exceptions.

Fix the alignment by positioning the DMA area in front of the allocation
and use memory at the end of the area for storing the orginal
transfer_buffer pointer. This may have the added benefit of increased
performance as the DMA area is now fully aligned on all architectures.

Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM).

Fixes: 3bc04e28a030 ("usb: dwc2: host: Get aligned DMA in a more supported way")
Cc: 
Reviewed-by: Douglas Anderson 
Signed-off-by: Antti Seppälä 
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

usb: core: handle hub C_PORT_OVER_CURRENT condition

2018-07-28T05:55:44+00:00

commit 249a32b7eeb3edb6897dd38f89651a62163ac4ed upstream.

Based on USB2.0 Spec Section 11.12.5,

  "If a hub has per-port power switching and per-port current limiting,
  an over-current on one port may still cause the power on another port
  to fall below specific minimums. In this case, the affected port is
  placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the
  port, but PORT_OVER_CURRENT is not set."

so let's check C_PORT_OVER_CURRENT too for over current condition.

Fixes: 08d1dec6f405 ("usb:hub set hub->change_bits when over-current happens")
Cc: 
Tested-by: Alessandro Antenucci 
Signed-off-by: Bin Liu 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

usb: cdc_acm: Add quirk for Castles VEGA3000

2018-07-28T05:55:44+00:00

commit 1445cbe476fc3dd09c0b380b206526a49403c071 upstream.

The device (a POS terminal) implements CDC ACM, but has not union
descriptor.

Signed-off-by: Lubomir Rintel 
Acked-by: Oliver Neukum 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

xhci: Fix perceived dead host due to runtime suspend race with event handler

2018-07-25T09:25:11+00:00

commit 229bc19fd7aca4f37964af06e3583c1c8f36b5d6 upstream.

Don't rely on event interrupt (EINT) bit alone to detect pending port
change in resume. If no change event is detected the host may be suspended
again, oterwise roothubs are resumed.

There is a lag in xHC setting EINT. If we don't notice the pending change
in resume, and the controller is runtime suspeded again, it causes the
event handler to assume host is dead as it will fail to read xHC registers
once PCI puts the controller to D3 state.

[  268.520969] xhci_hcd: xhci_resume: starting port polling.
[  268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling.
[  268.521030] xhci_hcd: xhci_suspend: stopping port polling.
[  268.521040] xhci_hcd: // Setting command ring address to 0x349bd001
[  268.521139] xhci_hcd: Port Status Change Event for port 3
[  268.521149] xhci_hcd: resume root hub
[  268.521163] xhci_hcd: port resume event for port 3
[  268.521168] xhci_hcd: xHC is not running.
[  268.521174] xhci_hcd: handle_port_status: starting port polling.
[  268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead

The EINT lag is described in a additional note in xhci specs 4.19.2:

"Due to internal xHC scheduling and system delays, there will be a lag
between a change bit being set and the Port Status Change Event that it
generated being written to the Event Ring. If SW reads the PORTSC and
sees a change bit set, there is no guarantee that the corresponding Port
Status Change Event has already been written into the Event Ring."

Cc: 
Signed-off-by: Mathias Nyman 
Signed-off-by: Kai-Heng Feng 
Signed-off-by: Greg Kroah-Hartman

xhci: Fix USB3 NULL pointer dereference at logical disconnect.

2018-07-22T12:28:48+00:00

commit 2278446e2b7cd33ad894b32e7eb63afc7db6c86e upstream.

Hub driver will try to disable a USB3 device twice at logical disconnect,
racing with xhci_free_dev() callback from the first port disable.

This can be triggered with "udisksctl power-off --block-device "
or by writing "1" to the "remove" sysfs file for a USB3 device
in 4.17-rc4.

USB3 devices don't have a similar disabled link state as USB2 devices,
and use a U3 suspended link state instead. In this state the port
is still enabled and connected.

hub_port_connect() first disconnects the device, then later it notices
that device is still enabled (due to U3 states) it will try to disable
the port again (set to U3).

The xhci_free_dev() called during device disable is async, so checking
for existing xhci->devs[i] when setting link state to U3 the second time
was successful, even if device was being freed.

The regression was caused by, and whole thing revealed by,
Commit 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device")
which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned.
and causes a NULL pointer dereference the second time we try to set U3.

Fix this by checking xhci->devs[i]->udev exists before setting link state.

The original patch went to stable so this fix needs to be applied there as
well.

Fixes: 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device")
Cc: 
Reported-by: Jordan Glover 
Tested-by: Jordan Glover 
Signed-off-by: Mathias Nyman 
Signed-off-by: Sudip Mukherjee 
Signed-off-by: Greg Kroah-Hartman

xhci: xhci-mem: off by one in xhci_stream_id_to_ring()

2018-07-17T09:39:26+00:00

commit 313db3d6488bb03b61b99de9dbca061f1fd838e1 upstream.

The > should be >= here so that we don't read one element beyond the end
of the ep->stream_info->stream_rings[] array.

Fixes: e9df17eb1408 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Signed-off-by: Dan Carpenter 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usb: quirks: add delay quirks for Corsair Strafe

2018-07-17T09:39:26+00:00

commit bba57eddadda936c94b5dccf73787cb9e159d0a5 upstream.

Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.

With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.

Signed-off-by: Nico Sneck 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman