linux-stable.git/drivers/usb, branch v3.7.3 Linux kernel stable tree USB: ehci: make debug port in-use detection functional again 2013-01-17T16:46:39+00:00 Jan Beulich JBeulich@suse.com 2012-12-19T16:15:56+00:00 8a935b4ad29d83731572f0eb10f033fee45ae2e3 commit 75e1a2ae1f61ce1ae640410ba757bba84bd9fefe upstream. Debug port in-use determination must be done before the controller gets reset the first time, i.e. before the call to ehci_setup() as of commit 1a49e2ac9651df7349867a5cf44e2c83de1046af. That commit effectively rendered commit 9fa5780beea1274d498a224822397100022da7d4 useless. While moving that code around, also fix the BAR determination - the respective capability field is a 3- rather than a 2-bit one -, and use PCI_CAP_ID_DBG instead of the literal 0x0a. It's unclear to me whether the debug port functionality is important enough to warrant fixing this in stable kernels too. Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 75e1a2ae1f61ce1ae640410ba757bba84bd9fefe upstream.

Debug port in-use determination must be done before the controller gets
reset the first time, i.e. before the call to ehci_setup() as of commit
1a49e2ac9651df7349867a5cf44e2c83de1046af. That commit effectively
rendered commit 9fa5780beea1274d498a224822397100022da7d4 useless.

While moving that code around, also fix the BAR determination - the
respective capability field is a 3- rather than a 2-bit one -, and use
PCI_CAP_ID_DBG instead of the literal 0x0a.

It's unclear to me whether the debug port functionality is important
enough to warrant fixing this in stable kernels too.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Handle HS bulk/ctrl endpoints that don't NAK. 2013-01-17T16:46:39+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-12-17T22:12:35+00:00 b8038a41540e8bc559bff3f131989a0bcbc5905a commit 55c1945edaac94c5338a3647bc2e85ff75d9cf36 upstream. A high speed control or bulk endpoint may have bInterval set to zero, which means it does not NAK. If bInterval is non-zero, it means the endpoint NAKs at a rate of 2^(bInterval - 1). The xHCI code to compute the NAK interval does not handle the special case of zero properly. The current code unconditionally subtracts one from bInterval and uses it as an exponent. This causes a very large bInterval to be used, and warning messages like these will be printed: usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes This may cause the xHCI host hardware to reject the Configure Endpoint command, which means the HS device will be unusable under xHCI ports. This patch should be backported to kernels as old as 2.6.31, that contain commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math in xhci_get_endpoint_interval()". Reported-by: Vincent Pelletier <plr.vincent@gmail.com> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 55c1945edaac94c5338a3647bc2e85ff75d9cf36 upstream.

A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK.  If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).

The xHCI code to compute the NAK interval does not handle the special
case of zero properly.  The current code unconditionally subtracts one
from bInterval and uses it as an exponent.  This causes a very large
bInterval to be used, and warning messages like these will be printed:

usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes

This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.

This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math in
xhci_get_endpoint_interval()".

Reported-by: Vincent Pelletier <plr.vincent@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: hub: handle claim of enabled remote wakeup after reset 2013-01-17T16:46:39+00:00 Oliver Neukum oliver@neukum.org 2012-11-29T14:05:57+00:00 3cf79239413526ca844c97a0c175a5bc5bfe45a5 commit 07e72b95f5038cc82304b9a4a2eb7f9fc391ea68 upstream. Some touchscreens have buggy firmware which claims remote wakeup to be enabled after a reset. They nevertheless crash if the feature is cleared by the host. Add a check for reset resume before checking for an enabled remote wakeup feature. On compliant devices the feature must be cleared after a reset anyway. Signed-off-by: Oliver Neukum <oneukum@suse.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 07e72b95f5038cc82304b9a4a2eb7f9fc391ea68 upstream.

Some touchscreens have buggy firmware which claims
remote wakeup to be enabled after a reset. They nevertheless
crash if the feature is cleared by the host.
Add a check for reset resume before checking for
an enabled remote wakeup feature. On compliant
devices the feature must be cleared after a reset anyway.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Avoid "dead ports", add roothub port polling. 2013-01-17T16:46:39+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-11-27T20:30:23+00:00 35b3b7dc3d885ca753653d61a0ef5c4318f5e9f6 commit c52804a472649b2e5005342308739434cbd51119 upstream. The USB core hub thread (khubd) is designed with external USB hubs in mind. It expects that if a port status change bit is set, the hub will continue to send a notification through the hub status data transfer. Basically, it expects hub notifications to be level-triggered. The xHCI host controller is designed to be edge-triggered on the logical 'OR' of all the port status change bits. When all port status change bits are clear, and a new change bit is set, the xHC will generate a Port Status Change Event. If another change bit is set in the same port status register before the first bit is cleared, it will not send another event. This means that the hub code may lose port status changes because of race conditions between clearing change bits. The user sees this as a "dead port" that doesn't react to device connects. The fix is to turn on port polling whenever a new change bit is set. Once the USB core issues a hub status request that shows that no change bits are set in any USB ports, turn off port polling. We can't allow the USB core to poll the roothub for port events during host suspend because if the PCI host is in D3cold, the port registers will be all f's. Instead, stop the port polling timer, and unconditionally restart it when the host resumes. If there are no port change bits set after the resume, the first call to hub_status_data will disable polling. This patch should be backported to stable kernels with the first xHCI support, 2.6.31 and newer, that include the commit 0f2a79300a1471cf92ab43af165ea13555c8b0a5 "USB: xhci: Root hub support." There will be merge conflicts because the check for HC_STATE_SUSPENDED was moved into xhci_suspend in 3.8. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c52804a472649b2e5005342308739434cbd51119 upstream.

The USB core hub thread (khubd) is designed with external USB hubs in
mind.  It expects that if a port status change bit is set, the hub will
continue to send a notification through the hub status data transfer.
Basically, it expects hub notifications to be level-triggered.

The xHCI host controller is designed to be edge-triggered on the logical
'OR' of all the port status change bits.  When all port status change
bits are clear, and a new change bit is set, the xHC will generate a
Port Status Change Event.  If another change bit is set in the same port
status register before the first bit is cleared, it will not send
another event.

This means that the hub code may lose port status changes because of
race conditions between clearing change bits.  The user sees this as a
"dead port" that doesn't react to device connects.

The fix is to turn on port polling whenever a new change bit is set.
Once the USB core issues a hub status request that shows that no change
bits are set in any USB ports, turn off port polling.

We can't allow the USB core to poll the roothub for port events during
host suspend because if the PCI host is in D3cold, the port registers
will be all f's.  Instead, stop the port polling timer, and
unconditionally restart it when the host resumes.  If there are no port
change bits set after the resume, the first call to hub_status_data will
disable polling.

This patch should be backported to stable kernels with the first xHCI
support, 2.6.31 and newer, that include the commit
0f2a79300a1471cf92ab43af165ea13555c8b0a5 "USB: xhci: Root hub support."
There will be merge conflicts because the check for HC_STATE_SUSPENDED
was moved into xhci_suspend in 3.8.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: Handle warm reset failure on empty port. 2013-01-17T16:46:39+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-11-15T01:58:04+00:00 f7965c0846d74b270e246c1470ca955d5078eb07 commit 65bdac5effd15d6af619b3b7218627ef4d84ed6a upstream. An empty port can transition to either Inactive or Compliance Mode if a newly connected USB 3.0 device fails to link train. In that case, we issue a warm reset. Some devices, such as John's Roseweil eusb3 enclosure, slip back into Compliance Mode after the warm reset. The current warm reset code does not check for device connect status on warm reset completion, and it incorrectly reports the warm reset succeeded. This causes the USB core to attempt to send a Set Address control transfer to a port in Compliance Mode, which will always fail. Make hub_port_wait_reset check the current connect status and link state after the warm reset completes. Return a failure status if the device is disconnected or the link state is Compliance Mode or SS.Inactive. Make hub_events disable the port if warm reset fails. This will disable the port, and then bring it back into the RxDetect state. Make the USB core ignore the connect change until the device reconnects. Note that this patch does NOT handle connected devices slipping into the Inactive state very well. This is a concern, because devices can go into the Inactive state on U1/U2 exit failure. However, the fix for that case is too large for stable, so it will be submitted in a separate patch. This patch should be backported to kernels as old as 3.2, contain the commit ID 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine warm reset logic" Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: John Covici <covici@ccs.covici.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 65bdac5effd15d6af619b3b7218627ef4d84ed6a upstream.

An empty port can transition to either Inactive or Compliance Mode if a
newly connected USB 3.0 device fails to link train.  In that case, we
issue a warm reset.  Some devices, such as John's Roseweil eusb3
enclosure, slip back into Compliance Mode after the warm reset.

The current warm reset code does not check for device connect status on
warm reset completion, and it incorrectly reports the warm reset
succeeded.  This causes the USB core to attempt to send a Set Address
control transfer to a port in Compliance Mode, which will always fail.

Make hub_port_wait_reset check the current connect status and link state
after the warm reset completes.  Return a failure status if the device
is disconnected or the link state is Compliance Mode or SS.Inactive.

Make hub_events disable the port if warm reset fails.  This will disable
the port, and then bring it back into the RxDetect state.  Make the USB
core ignore the connect change until the device reconnects.

Note that this patch does NOT handle connected devices slipping into the
Inactive state very well.  This is a concern, because devices can go
into the Inactive state on U1/U2 exit failure.  However, the fix for
that case is too large for stable, so it will be submitted in a separate
patch.

This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine warm
reset logic"

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: Ignore port state until reset completes. 2013-01-17T16:46:39+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-11-15T22:58:04+00:00 bbd31bebacee9a324beb67db5cd1f70dd9a9c2d9 commit 4f43447e62b37ee19c82a13f72f35b1ca60a74d3 upstream. The port reset code bails out early if the current connect status is cleared (device disconnected). If we're issuing a hot reset, it may also look at the link state before the reset is finished. Section 10.14.2.6 of the USB 3.0 spec says that when a port enters the Error state or Resetting state, the port connection bit retains the value from the previous state. Therefore we can't trust it until the reset finishes. Also, the xHCI spec section 4.19.1.2.5 says software shall ignore the link state while the port is resetting, as it can be in an unknown state. The port state during reset is also unknown for USB 2.0 hubs. The hub sends a reset signal by driving the bus into an SE0 state. This overwhelms the "connect" signal from the device, so the port can't tell whether anything is connected or not. Fix the port reset code to ignore the port link state and current connect bit until the reset finishes, and USB_PORT_STAT_RESET is cleared. Remove the check for USB_PORT_STAT_C_BH_RESET in the warm reset case, because it's redundant. When the warm reset finishes, the port reset bit will be cleared at the same time USB_PORT_STAT_C_BH_RESET is set. Remove the now-redundant check for a cleared USB_PORT_STAT_RESET bit in the code to deal with the finished reset. This patch should be backported to all stable kernels. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 4f43447e62b37ee19c82a13f72f35b1ca60a74d3 upstream.

The port reset code bails out early if the current connect status is
cleared (device disconnected).  If we're issuing a hot reset, it may
also look at the link state before the reset is finished.

Section 10.14.2.6 of the USB 3.0 spec says that when a port enters the
Error state or Resetting state, the port connection bit retains the
value from the previous state.  Therefore we can't trust it until the
reset finishes.  Also, the xHCI spec section 4.19.1.2.5 says software
shall ignore the link state while the port is resetting, as it can be in
an unknown state.

The port state during reset is also unknown for USB 2.0 hubs.  The hub
sends a reset signal by driving the bus into an SE0 state.  This
overwhelms the "connect" signal from the device, so the port can't tell
whether anything is connected or not.

Fix the port reset code to ignore the port link state and current
connect bit until the reset finishes, and USB_PORT_STAT_RESET is
cleared.

Remove the check for USB_PORT_STAT_C_BH_RESET in the warm reset case,
because it's redundant.  When the warm reset finishes, the port reset
bit will be cleared at the same time USB_PORT_STAT_C_BH_RESET is set.
Remove the now-redundant check for a cleared USB_PORT_STAT_RESET bit
in the code to deal with the finished reset.

This patch should be backported to all stable kernels.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: Increase reset timeout. 2013-01-17T16:46:38+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-11-15T01:16:52+00:00 7462d1bd2e5e5d5d993aa815f89afd4e4d1dd35a commit 77c7f072c87fa951e9a74805febf26466f31170c upstream. John's NEC 0.96 xHCI host controller needs a longer timeout for a warm reset to complete. The logs show it takes 650ms to complete the warm reset, so extend the hub reset timeout to 800ms to be on the safe side. This commit should be backported to kernels as old as 3.2, that contain the commit 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine warm reset logic". Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: John Covici <covici@ccs.covici.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 77c7f072c87fa951e9a74805febf26466f31170c upstream.

John's NEC 0.96 xHCI host controller needs a longer timeout for a warm
reset to complete.  The logs show it takes 650ms to complete the warm
reset, so extend the hub reset timeout to 800ms to be on the safe side.

This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine
warm reset logic".

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: Allow USB 3.0 ports to be disabled. 2013-01-17T16:46:38+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-11-15T00:42:32+00:00 17722a0806c1033edcc564958a929f836bc4050b commit 41e7e056cdc662f704fa9262e5c6e213b4ab45dd upstream. If hot and warm reset fails, or a port remains in the Compliance Mode, the USB core needs to be able to disable a USB 3.0 port. Unlike USB 2.0 ports, once the port is placed into the Disabled link state, it will not report any new device connects. To get device connect notifications, we need to put the link into the Disabled state, and then the RxDetect state. The xHCI driver needs to atomically clear all change bits on USB 3.0 port disable, so that we get Port Status Change Events for future port changes. We could technically do this in the USB core instead of in the xHCI roothub code, since the port state machine can't advance out of the disabled state until we set the link state to RxDetect. However, external USB 3.0 hubs don't need this code. They are level-triggered, not edge-triggered like xHCI, so they will continue to send interrupt events when any change bit is set. Therefore it doesn't make sense to put this code in the USB core. This patch is part of a series to fix several reports of infinite loops on device enumeration failure. This includes John, when he boots with a USB 3.0 device (Roseweil eusb3 enclosure) attached to his NEC 0.96 host controller. The fix requires warm reset support, so it does not make sense to backport this patch to stable kernels without warm reset support. This patch should be backported to kernels as old as 3.2, contain the commit ID 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine warm reset logic" Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: John Covici <covici@ccs.covici.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 41e7e056cdc662f704fa9262e5c6e213b4ab45dd upstream.

If hot and warm reset fails, or a port remains in the Compliance Mode,
the USB core needs to be able to disable a USB 3.0 port.  Unlike USB 2.0
ports, once the port is placed into the Disabled link state, it will not
report any new device connects.  To get device connect notifications, we
need to put the link into the Disabled state, and then the RxDetect
state.

The xHCI driver needs to atomically clear all change bits on USB 3.0
port disable, so that we get Port Status Change Events for future port
changes.  We could technically do this in the USB core instead of in the
xHCI roothub code, since the port state machine can't advance out of the
disabled state until we set the link state to RxDetect.  However,
external USB 3.0 hubs don't need this code.  They are level-triggered,
not edge-triggered like xHCI, so they will continue to send interrupt
events when any change bit is set.  Therefore it doesn't make sense to
put this code in the USB core.

This patch is part of a series to fix several reports of infinite loops
on device enumeration failure.  This includes John, when he boots with
a USB 3.0 device (Roseweil eusb3 enclosure) attached to his NEC 0.96
host controller.  The fix requires warm reset support, so it does not
make sense to backport this patch to stable kernels without warm reset
support.

This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine warm
reset logic"

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: Ignore xHCI Reset Device status. 2013-01-17T16:46:38+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-11-15T00:10:49+00:00 00e33f5e757dc64908a1eb65c17800ef81784f8a commit 8b8132bc3d1cc3d4c0687e4d638a482fa920d98a upstream. When the USB core finishes reseting a USB device, the xHCI driver sends a Reset Device command to the host. The xHC then updates its internal representation of the USB device to the 'Default' device state. If the device was already in the Default state, the xHC will complete the command with an error status. If a device needs to be reset several times during enumeration, the second reset will always fail because of the xHCI Reset Device command. This can cause issues during enumeration. For example, usb_reset_and_verify_device calls into hub_port_init in a loop. Say that on the first call into hub_port_init, the device is successfully reset, but doesn't respond to several set address control transfers. Then the port will be disabled, but the udev will remain in tact. usb_reset_and_verify_device will call into hub_port_init again. On the second call into hub_port_init, the device will be reset, and the xHCI driver will issue a Reset Device command. This command will fail (because the device is already in the Default state), and usb_reset_and_verify_device will fail. The port will be disabled, and the device won't be able to enumerate. Fix this by ignoring the return value of the HCD reset_device callback. This commit should be backported to kernels as old as 3.2, that contain the commit 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine warm reset logic". Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 8b8132bc3d1cc3d4c0687e4d638a482fa920d98a upstream.

When the USB core finishes reseting a USB device, the xHCI driver sends
a Reset Device command to the host.  The xHC then updates its internal
representation of the USB device to the 'Default' device state.  If the
device was already in the Default state, the xHC will complete the
command with an error status.

If a device needs to be reset several times during enumeration, the
second reset will always fail because of the xHCI Reset Device command.
This can cause issues during enumeration.

For example, usb_reset_and_verify_device calls into hub_port_init in a
loop.  Say that on the first call into hub_port_init, the device is
successfully reset, but doesn't respond to several set address control
transfers.  Then the port will be disabled, but the udev will remain in
tact.  usb_reset_and_verify_device will call into hub_port_init again.

On the second call into hub_port_init, the device will be reset, and the
xHCI driver will issue a Reset Device command.  This command will fail
(because the device is already in the Default state), and
usb_reset_and_verify_device will fail.  The port will be disabled, and
the device won't be able to enumerate.

Fix this by ignoring the return value of the HCD reset_device callback.

This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine
warm reset logic".

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: Add device quirk for Microsoft VX700 webcam 2013-01-17T16:46:38+00:00 Andreas Fleig andreasfleig@gmail.com 2012-12-05T15:17:49+00:00 ed25f8809a6c3036f40f1467202db2198180034e commit bc009eca8d539162f7271c2daf0ab5e9e3bb90a0 upstream. Add device quirk for Microsoft Lifecam VX700 v2.0 webcams. Fixes squeaking noise of the microphone. Signed-off-by: Andreas Fleig <andreasfleig@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit bc009eca8d539162f7271c2daf0ab5e9e3bb90a0 upstream.

Add device quirk for Microsoft Lifecam VX700 v2.0 webcams.
Fixes squeaking noise of the microphone.

Signed-off-by: Andreas Fleig <andreasfleig@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>