commit 6048e4c69d80600baba35856651056860d5d8f5a upstream. dwc3_gadget_set_ep_config expects maxburst as incremented by 1. So, by default initialize ep->maxburst to 1 for ep0. Signed-off-by: Pratyush Anand <pratyush.anand@st.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f815a0a700bc10547449bde6c106051a035a1b9 upstream. This patch (as1644) fixes a race that occurs during startup in uhci-hcd. If the IRQ line is shared with other devices, it's possible for the handler routine to be called before the data structures are fully initialized. The problem is fixed by adding a check to the IRQ handler routine. If the initialization hasn't finished yet, the routine will return immediately. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Don Zickus <dzickus@redhat.com> Tested-by: "Huang, Adrian (ISS Linux TW)" <adrian.huang@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no> commit 2291dff02e5f8c708a46a7c4c888f2c467e26642 upstream. The driver description files gives these names to the vendor specific functions on this modem: Diag VID_19D2&PID_0265&MI_00 NMEA VID_19D2&PID_0265&MI_01 AT cmd VID_19D2&PID_0265&MI_02 Modem VID_19D2&PID_0265&MI_03 Net VID_19D2&PID_0265&MI_04 Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99beb2e9687ffd61c92a9875141eabe6f57a71b9 upstream. The driver description files gives these names to the vendor specific functions on this modem: Diagnostics VID_2357&PID_0201&MI_00 NMEA VID_2357&PID_0201&MI_01 Modem VID_2357&PID_0201&MI_03 Networkcard VID_2357&PID_0201&MI_04 Reported-by: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36caff5d795429c572443894e8789c2150dd796b upstream. This patch (as1631) fixes a bug that shows up when a config change fails for a device under an xHCI controller. The controller needs to be told to disable the endpoints that have been enabled for the new config. The existing code does this, but before storing the information about which endpoints were enabled! As a result, any second attempt to install the new config is doomed to fail because xhci-hcd will refuse to enable an endpoint that is already enabled. The patch optimistically initializes the new endpoints' device structures before asking the device to switch to the new config. If the request fails then the endpoint information is already stored, so we can use usb_hcd_alloc_bandwidth() to disable the endpoints with no trouble. The rest of the error path is slightly more complex now; we have to disable the new interfaces and call put_device() rather than simply deallocating them. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Matthias Schniedermeyer <ms@citd.de> CC: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55c1945edaac94c5338a3647bc2e85ff75d9cf36 upstream. A high speed control or bulk endpoint may have bInterval set to zero, which means it does not NAK. If bInterval is non-zero, it means the endpoint NAKs at a rate of 2^(bInterval - 1). The xHCI code to compute the NAK interval does not handle the special case of zero properly. The current code unconditionally subtracts one from bInterval and uses it as an exponent. This causes a very large bInterval to be used, and warning messages like these will be printed: usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes This may cause the xHCI host hardware to reject the Configure Endpoint command, which means the HS device will be unusable under xHCI ports. This patch should be backported to kernels as old as 2.6.31, that contain commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math in xhci_get_endpoint_interval()". Reported-by: Vincent Pelletier <plr.vincent@gmail.com> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07e72b95f5038cc82304b9a4a2eb7f9fc391ea68 upstream. Some touchscreens have buggy firmware which claims remote wakeup to be enabled after a reset. They nevertheless crash if the feature is cleared by the host. Add a check for reset resume before checking for an enabled remote wakeup feature. On compliant devices the feature must be cleared after a reset anyway. Signed-off-by: Oliver Neukum <oneukum@suse.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c52804a472649b2e5005342308739434cbd51119 upstream. The USB core hub thread (khubd) is designed with external USB hubs in mind. It expects that if a port status change bit is set, the hub will continue to send a notification through the hub status data transfer. Basically, it expects hub notifications to be level-triggered. The xHCI host controller is designed to be edge-triggered on the logical 'OR' of all the port status change bits. When all port status change bits are clear, and a new change bit is set, the xHC will generate a Port Status Change Event. If another change bit is set in the same port status register before the first bit is cleared, it will not send another event. This means that the hub code may lose port status changes because of race conditions between clearing change bits. The user sees this as a "dead port" that doesn't react to device connects. The fix is to turn on port polling whenever a new change bit is set. Once the USB core issues a hub status request that shows that no change bits are set in any USB ports, turn off port polling. We can't allow the USB core to poll the roothub for port events during host suspend because if the PCI host is in D3cold, the port registers will be all f's. Instead, stop the port polling timer, and unconditionally restart it when the host resumes. If there are no port change bits set after the resume, the first call to hub_status_data will disable polling. This patch should be backported to stable kernels with the first xHCI support, 2.6.31 and newer, that include the commit 0f2a79300a1471cf92ab43af165ea13555c8b0a5 "USB: xhci: Root hub support." There will be merge conflicts because the check for HC_STATE_SUSPENDED was moved into xhci_suspend in 3.8. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65bdac5effd15d6af619b3b7218627ef4d84ed6a upstream. An empty port can transition to either Inactive or Compliance Mode if a newly connected USB 3.0 device fails to link train. In that case, we issue a warm reset. Some devices, such as John's Roseweil eusb3 enclosure, slip back into Compliance Mode after the warm reset. The current warm reset code does not check for device connect status on warm reset completion, and it incorrectly reports the warm reset succeeded. This causes the USB core to attempt to send a Set Address control transfer to a port in Compliance Mode, which will always fail. Make hub_port_wait_reset check the current connect status and link state after the warm reset completes. Return a failure status if the device is disconnected or the link state is Compliance Mode or SS.Inactive. Make hub_events disable the port if warm reset fails. This will disable the port, and then bring it back into the RxDetect state. Make the USB core ignore the connect change until the device reconnects. Note that this patch does NOT handle connected devices slipping into the Inactive state very well. This is a concern, because devices can go into the Inactive state on U1/U2 exit failure. However, the fix for that case is too large for stable, so it will be submitted in a separate patch. This patch should be backported to kernels as old as 3.2, contain the commit ID 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine warm reset logic" Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: John Covici <covici@ccs.covici.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f43447e62b37ee19c82a13f72f35b1ca60a74d3 upstream. The port reset code bails out early if the current connect status is cleared (device disconnected). If we're issuing a hot reset, it may also look at the link state before the reset is finished. Section 10.14.2.6 of the USB 3.0 spec says that when a port enters the Error state or Resetting state, the port connection bit retains the value from the previous state. Therefore we can't trust it until the reset finishes. Also, the xHCI spec section 4.19.1.2.5 says software shall ignore the link state while the port is resetting, as it can be in an unknown state. The port state during reset is also unknown for USB 2.0 hubs. The hub sends a reset signal by driving the bus into an SE0 state. This overwhelms the "connect" signal from the device, so the port can't tell whether anything is connected or not. Fix the port reset code to ignore the port link state and current connect bit until the reset finishes, and USB_PORT_STAT_RESET is cleared. Remove the check for USB_PORT_STAT_C_BH_RESET in the warm reset case, because it's redundant. When the warm reset finishes, the port reset bit will be cleared at the same time USB_PORT_STAT_C_BH_RESET is set. Remove the now-redundant check for a cleared USB_PORT_STAT_RESET bit in the code to deal with the finished reset. This patch should be backported to all stable kernels. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>