linux-stable.git/drivers/usb, branch v3.2.75

usb: xhci: fix config fail of FS hub behind a HS hub with MTT

2015-12-30T02:26:00+00:00

commit 096b110a3dd3c868e4610937c80d2e3f3357c1a9 upstream.

if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2

Signed-off-by: Chunfeng Yun 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message

2015-12-30T02:25:59+00:00

commit 5377adb092664d336ac212499961cac5e8728794 upstream.

usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.

Fixes: ff30cbc8da42 ("usb: Use the USB_SS_MULT() macro to get the ...")
Signed-off-by: Ben Hutchings 
Signed-off-by: Greg Kroah-Hartman

USB: whci-hcd: add check for dma mapping error

2015-12-30T02:25:59+00:00

commit f9fa1887dcf26bd346665a6ae3d3f53dec54cba1 upstream.

qset_fill_page_list() do not check for dma mapping errors.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: cdc_acm: Ignore Infineon Flash Loader utility

2015-12-30T02:25:57+00:00

commit f33a7f72e5fc033daccbb8d4753d7c5c41a4d67b upstream.

Some modems, such as the Telit UE910, are using an Infineon Flash Loader
utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC
Data). The latter can be used as a serial interface to upgrade the
firmware of the modem. However, that isn't possible when the cdc-acm
driver takes control of the device.

The following is an explanation of the behaviour by Daniele Palmas during
discussion on linux-usb.

"This is what happens when the device is turned on (without modifying
the drivers):

[155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci
[155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11
[155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041
[155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device

This is the flashing device that is caught by the cdc-acm driver. Once
the ttyACM appears, the application starts sending a magic string
(simple write on the file descriptor) to keep the device in flashing
mode. If this magic string is not properly received in a certain time
interval, the modem goes on in normal operative mode:

[155493.748094] usb 1-3: USB disconnect, device number 27
[155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci
[155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021
[155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM
[155495.059989] usb 1-3: Manufacturer: Telit
[155495.059992] usb 1-3: SerialNumber: 359658044004697
[155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
[155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device
[155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device
[155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device
[155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device
[155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device
[155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14

Using the cdc-acm driver, the string, though being sent in the same way
than using the usb-serial-simple driver (I can confirm that the data is
passing properly since I used an hw usb sniffer), does not make the
device to stay in flashing mode."

Signed-off-by: Jonas Jonsson 
Tested-by: Daniele Palmas 
Signed-off-by: Johan Hovold 
Signed-off-by: Ben Hutchings

USB: cdc-acm - Add IGNORE_DEVICE quirk

2015-12-30T02:25:57+00:00

Extracted from commit 16142655269a ("USB: cdc-acm - blacklist IMS PCU
device").

Signed-off-by: Ben Hutchings

USB: cp210x: Remove CP2110 ID from compatibility list

2015-12-30T02:25:57+00:00

commit 7c90e610b60cd1ed6abafd806acfaedccbbe52d1 upstream.

CP2110 ID (0x10c4, 0xea80) doesn't belong here because it's a HID
and completely different from CP210x devices.

Signed-off-by: Konstantin Shkolnyy 
Signed-off-by: Johan Hovold 
Signed-off-by: Ben Hutchings

usblp: do not set TASK_INTERRUPTIBLE before lock

2015-12-30T02:25:56+00:00

commit 19cd80a214821f4b558560ebd76bfb2c38b4f3d8 upstream.

It is not permitted to set task state before lock. usblp_wwait sets
the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible.
Upon return from that function, the state will be TASK_RUNNING again.

This is clearly a bug and a warning is generated with LOCKDEP too:
WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90()
do not call blocking ops when !TASK_RUNNING; state=1 set at [] usblp_wwait+0xa0/0x310 [usblp]
Modules linked in: ...
CPU: 1 PID: 5109 Comm: captmon Tainted: G        W       4.2.5-0.gef2823b-default #1
Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012
 ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000
 ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282
 ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508
Call Trace:
...
 [] warn_slowpath_fmt+0x46/0x50
 [] __might_sleep+0x7d/0x90
 [] mutex_lock_interruptible_nested+0x2f/0x4b0
 [] usblp_wwait+0xcc/0x310 [usblp]
 [] usblp_write+0x72/0x350 [usblp]
 [] __vfs_write+0x28/0xf0
...

Commit 7f477358e2384c54b190cc3b6ce28277050a041b (usblp: Implement the
ENOSPC convention) moved the set prior locking. So move it back after
the lock.

Signed-off-by: Jiri Slaby 
Fixes: 7f477358e2 ("usblp: Implement the ENOSPC convention")
Acked-By: Pete Zaitcev 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: option: add XS Stick W100-2 from 4G Systems

2015-12-30T02:25:56+00:00

commit 638148e20c7f8f6e95017fdc13bce8549a6925e0 upstream.

Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1c9e ProdID=9b01 Rev=02.32
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=
C:  #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Now all important things are there:

wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)

There is also ttyUSB0, but it is not usable, at least not for at.

The device works well with qmi and ModemManager-NetworkManager.
"

Reported-by: Thomas Schäfer 
Signed-off-by: Bjørn Mork 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings

xhci: Workaround to get Intel xHCI reset working more reliably

2015-12-30T02:25:56+00:00

commit a5964396190d0c40dd549c23848c282fffa5d1f2 upstream.

Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.

Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.

Signed-off-by: Rajmohan Mani 
Tested-by: Joe Lawrence 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings

xhci: Add XHCI_INTEL_HOST quirk

2015-12-30T02:25:56+00:00

Extracted from commit e3567d2c15a7 ("xhci: Add Intel U1/U2 timeout policy.")

Signed-off-by: Ben Hutchings