linux-stable.git/drivers/usb, branch v3.2.30 Linux kernel stable tree EHCI: Update qTD next pointer in QH overlay region during unlink 2012-09-19T14:05:20+00:00 Pavankumar Kondeti pkondeti@codeaurora.org 2012-09-07T05:53:28+00:00 3bef14ff773afb2b26c05b30418a0b891563b0a9 commit 3d037774b42ed677f699b1dce7d548d55f4e4c2b upstream. There is a possibility of QH overlay region having reference to a stale qTD pointer during unlink. Consider an endpoint having two pending qTD before unlink process begins. The endpoint's QH queue looks like this. qTD1 --> qTD2 --> Dummy To unlink qTD2, QH is removed from asynchronous list and Asynchronous Advance Doorbell is programmed. The qTD1's next qTD pointer is set to qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell interrupt. If QH's current qTD pointer points to qTD1, transfer overlay region still have reference to qTD2. But qtD2 is just unlinked and freed. This may cause EHCI system error. Fix this by updating qTD next pointer in QH overlay region with the qTD next pointer of the current qTD. Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 3d037774b42ed677f699b1dce7d548d55f4e4c2b upstream.

There is a possibility of QH overlay region having reference to a stale
qTD pointer during unlink.

Consider an endpoint having two pending qTD before unlink process begins.
The endpoint's QH queue looks like this.

qTD1 --> qTD2 --> Dummy

To unlink qTD2, QH is removed from asynchronous list and Asynchronous
Advance Doorbell is programmed.  The qTD1's next qTD pointer is set to
qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell
interrupt.  If QH's current qTD pointer points to qTD1, transfer overlay
region still have reference to qTD2. But qtD2 is just unlinked and freed.
This may cause EHCI system error.  Fix this by updating qTD next pointer
in QH overlay region with the qTD next pointer of the current qTD.

Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: ftdi_sio: do not claim CDC ACM function 2012-09-19T14:05:19+00:00 Bjørn Mork bjorn@mork.no 2012-09-10T10:01:05+00:00 d3759eaf54695290840a06248512366b4e87a9cc commit f08dea734844aa42ec57c229b0b73b3d7d21f810 upstream. The Microchip vid:pid 04d8:000a is used for their CDC ACM demo firmware application. This is a device with a single function conforming to the CDC ACM specification and with the intention of demonstrating CDC ACM class firmware and driver interaction. The demo is used on a number of development boards, and may also be used unmodified by vendors using Microchip hardware. Some vendors have re-used this vid:pid for other types of firmware, emulating FTDI chips. Attempting to continue to support such devices without breaking class based applications that by matching on interface class/subclass/proto being ff/ff/00. I have no information about the actual device or interface descriptors, but this will at least make the proper CDC ACM devices work again. Anyone having details of the offending device's descriptors should update this entry with the details. Reported-by: Florian Wöhrl <fw@woehrl.biz> Reported-by: Xiaofan Chen <xiaofanc@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Bruno Thomsen <bruno.thomsen@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit f08dea734844aa42ec57c229b0b73b3d7d21f810 upstream.

The Microchip vid:pid 04d8:000a is used for their CDC ACM
demo firmware application.  This is a device with a single
function conforming to the CDC ACM specification and with
the intention of demonstrating CDC ACM class firmware and
driver interaction.  The demo is used on a number of
development boards, and may also be used unmodified by
vendors using Microchip hardware.

Some vendors have re-used this vid:pid for other types of
firmware, emulating FTDI chips. Attempting to continue to
support such devices without breaking class based
applications that by matching on interface
class/subclass/proto being ff/ff/00.  I have no information
about the actual device or interface descriptors, but this
will at least make the proper CDC ACM devices work again.
Anyone having details of the offending device's descriptors
should update this entry with the details.

Reported-by: Florian Wöhrl <fw@woehrl.biz>
Reported-by: Xiaofan Chen <xiaofanc@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: add device quirk for Joss Optical touchboard 2012-09-19T14:05:16+00:00 Alan Stern stern@rowland.harvard.edu 2012-09-04T14:41:02+00:00 06c181e04d2fb11e2671789ac7ce354e31621533 commit 92fc7a8b0f20bdb243c706daf42658e8e0cd2ef0 upstream. This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss infrared touchboard device. The device doesn't like to be asked for its interface strings. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: adam ? <adam3337@wp.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 92fc7a8b0f20bdb243c706daf42658e8e0cd2ef0 upstream.

This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss
infrared touchboard device.  The device doesn't like to be asked for
its interface strings.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: adam ? <adam3337@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: ftdi_sio: PID for NZR SEM 16+ USB 2012-09-19T14:05:15+00:00 Horst Schirmeier horst@schirmeier.com 2012-08-30T22:00:28+00:00 702066cc9b7651ccd94f02bde59355c659f74b52 commit 26a538b9ea2a3ee10dafc0068f0560dfd7b7ba37 upstream. This adds the USB PID for the NZR SEM 16+ USB energy monitor device <http://www.nzr.de>. It works perfectly with the GPL software on <http://schou.dk/linux/sparometer/>. Signed-off-by: Horst Schirmeier <horst@schirmeier.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 26a538b9ea2a3ee10dafc0068f0560dfd7b7ba37 upstream.

This adds the USB PID for the NZR SEM 16+ USB energy monitor device
<http://www.nzr.de>.  It works perfectly with the GPL software on
<http://schou.dk/linux/sparometer/>.

Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: ftdi-sio: add support for more Physik Instrumente devices 2012-09-19T14:05:15+00:00 Éric Piel piel@delmic.com 2012-09-04T15:25:06+00:00 01ce87e184a949dfd8fab6e508e7ed0ae476bc77 commit dafc4f7be1a556ca3868d343c00127728b397068 upstream. Commit b69cc672052540 added support for the E-861. After acquiring a C-867, I realised that every Physik Instrumente's device has a different PID. They are listed in the Windows device driver's .inf file. So here are all PIDs for the current (and probably future) USB devices from Physik Instrumente. Compiled, but only actually tested on the E-861 and C-867. Signed-off-by: Éric Piel <piel@delmic.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit dafc4f7be1a556ca3868d343c00127728b397068 upstream.

Commit b69cc672052540 added support for the E-861.  After acquiring a C-867, I
realised that every Physik Instrumente's device has a different PID. They are
listed in the Windows device driver's .inf file. So here are all PIDs for the
current (and probably future) USB devices from Physik Instrumente.

Compiled, but only actually tested on the E-861 and C-867.

Signed-off-by: Éric Piel <piel@delmic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: host: xhci: fix compilation error for non-PCI based stacks 2012-09-19T14:05:13+00:00 Moiz Sonasath m-sonasath@ti.com 2012-09-05T05:34:26+00:00 2bcd02db4deea25c9a5c8cca03b2fceba6596574 commit 296365781903226a3fb8758901eaeec09d2798e4 upstream. For non PCI-based stacks, this function call usb_disable_xhci_ports(to_pci_dev(hcd->self.controller)); made from xhci_shutdown is not applicable. Ideally, we wouldn't have any PCI-specific code on a generic driver such as the xHCI stack, but it looks like we should just stub usb_disable_xhci_ports() out for non-PCI devices. [ balbi@ti.com: slight improvement to commit log ] This patch should be backported to kernels as old as 3.0, since the commit it fixes (e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch PPT ports to EHCI on shutdown.") was marked for stable. Signed-off-by: Moiz Sonasath<m-sonasath@ti.com> Signed-off-by: Ruchika Kharwar <ruchika@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 296365781903226a3fb8758901eaeec09d2798e4 upstream.

For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.

Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.

[ balbi@ti.com: slight improvement to commit log ]

This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.

Signed-off-by: Moiz Sonasath<m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware 2012-09-19T14:05:13+00:00 Alexis R. Cortes alexis.cortes@ti.com 2012-08-03T19:00:27+00:00 874879c4643c481d50f34d6957207b5e444171b1 commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 upstream. This patch is intended to work around a known issue on the SN65LVPE502CP USB3.0 re-driver that can delay the negotiation between a device and the host past the usual handshake timeout. If that happens on the first insertion, the host controller port will enter in Compliance Mode and NO port status event will be generated (as per xHCI Spec) making impossible to detect this event by software. The port will remain in compliance mode until a warm reset is applied to it. As a result of this, the port will seem "dead" to the user and no device connections or disconnections will be detected. For solving this, the patch creates a timer which polls every 2 seconds the link state of each host controller's port (this by reading the PORTSC register) and recovers the port by issuing a Warm reset every time Compliance mode is detected. If a xHC USB3.0 port has previously entered to U0, the compliance mode issue will NOT occur only until system resumes from sleep/hibernate, therefore, the compliance mode timer is stopped when all xHC USB 3.0 ports have entered U0. The timer is initialized again after each system resume. Since the issue is being caused by a piece of hardware, the timer will be enabled ONLY on those systems that have the SN65LVPE502CP installed (this patch uses DMI strings for detecting those systems) therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK has been added to the xhci stack). This patch applies for these systems: Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820. This patch should be backported to kernels as old as 3.2, as that was the first kernel to support warm reset. The kernels will need to contain both commit 10d674a82e553cb8a1f41027bb3c3e309b3f6804 "USB: When hot reset for USB3 fails, try warm reset" and commit 8bea2bd37df08aaa599aa361a9f8b836ba98e554 "usb: Add support for root hub port status CAS". The first patch add warm reset support, and the second patch modifies the USB core to issue a warm reset when the port is in compliance mode. Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 upstream.

This patch is intended to work around a known issue on the
SN65LVPE502CP USB3.0 re-driver that can delay the negotiation
between a device and the host past the usual handshake timeout.

If that happens on the first insertion, the host controller
port will enter in Compliance Mode and NO port status event will
be generated (as per xHCI Spec) making impossible to detect this
event by software. The port will remain in compliance mode until
a warm reset is applied to it.

As a result of this, the port will seem "dead" to the user and no
device connections or disconnections will be detected.

For solving this, the patch creates a timer which polls every 2
seconds the link state of each host controller's port (this
by reading the PORTSC register) and recovers the port by issuing a
Warm reset every time Compliance mode is detected.

If a xHC USB3.0 port has previously entered to U0, the compliance
mode issue will NOT occur only until system resumes from
sleep/hibernate, therefore, the compliance mode timer is stopped
when all xHC USB 3.0 ports have entered U0. The timer is initialized
again after each system resume.

Since the issue is being caused by a piece of hardware, the timer
will be enabled ONLY on those systems that have the SN65LVPE502CP
installed (this patch uses DMI strings for detecting those systems)
therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK
has been added to the xhci stack).

This patch applies for these systems:
Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820.

This patch should be backported to kernels as old as 3.2, as that was
the first kernel to support warm reset.  The kernels will need to
contain both commit 10d674a82e553cb8a1f41027bb3c3e309b3f6804 "USB: When
hot reset for USB3 fails, try warm reset" and commit
8bea2bd37df08aaa599aa361a9f8b836ba98e554 "usb: Add support for root hub
port status CAS".  The first patch add warm reset support, and the
second patch modifies the USB core to issue a warm reset when the port
is in compliance mode.

Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: Make handover code more robust 2012-09-19T14:05:12+00:00 Matthew Garrett mjg@redhat.com 2012-08-14T20:44:49+00:00 43e3806177660ebb1fdd4ac8aedb0e62abfbe3e4 commit e955a1cd086de4d165ae0f4c7be7289d84b63bdc upstream. My test platform (Intel DX79SI) boots reliably under BIOS, but frequently crashes when booting via UEFI. I finally tracked this down to the xhci handoff code. It seems that reads from the device occasionally just return 0xff, resulting in xhci_find_next_cap_offset generating a value that's larger than the resource region. We then oops when attempting to read the value. Sanity checking that value lets us avoid the crash. I've no idea what's causing the underlying problem, and xhci still doesn't actually *work* even with this, but the machine at least boots which will probably make further debugging easier. This should be backported to kernels as old as 2.6.31, that contain the commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci: BIOS handoff and HW initialization." Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit e955a1cd086de4d165ae0f4c7be7289d84b63bdc upstream.

My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.

I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.

This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci: BIOS handoff
and HW initialization."

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: Fix a logical vs bitwise AND bug 2012-09-19T14:05:12+00:00 Dan Carpenter dan.carpenter@oracle.com 2012-08-13T16:57:03+00:00 52fa5d9c8c956ee587389bd662106a770de42827 commit 052c7f9ffb0e95843e75448d02664459253f9ff8 upstream. The intent was to test whether the flag was set. This patch should be backported to stable kernels as old as 3.0, since it fixes a bug in commit e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch PPT ports to EHCI on shutdown.", which was marked for stable. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 052c7f9ffb0e95843e75448d02664459253f9ff8 upstream.

The intent was to test whether the flag was set.

This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f474f0db3a4d940cae1423783edd966027 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: Switch PPT ports to EHCI on shutdown. 2012-09-19T14:05:12+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-07-23T15:59:30+00:00 201a1b49e0222de2d07c3a107c1bcd58891fbd54 commit e95829f474f0db3a4d940cae1423783edd966027 upstream. The Intel desktop boards DH77EB and DH77DF have a hardware issue that can be worked around by BIOS. If the USB ports are switched to xHCI on shutdown, the xHCI host will send a spurious interrupt, which will wake the system. Some BIOS will work around this, but not all. The bug can be avoided if the USB ports are switched back to EHCI on shutdown. The Intel Windows driver switches the ports back to EHCI, so change the Linux xHCI driver to do the same. Unfortunately, we can't tell the two effected boards apart from other working motherboards, because the vendors will change the DMI strings for the DH77EB and DH77DF boards to their own custom names. One example is Compulab's mini-desktop, the Intense-PC. Instead, key off the Panther Point xHCI host PCI vendor and device ID, and switch the ports over for all PPT xHCI hosts. The only impact this will have on non-effected boards is to add a couple hundred milliseconds delay on boot when the BIOS has to switch the ports over from EHCI to xHCI. This patch should be backported to kernels as old as 3.0, that contain the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Denis Turischev <denis@compulab.co.il> Tested-by: Denis Turischev <denis@compulab.co.il> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit e95829f474f0db3a4d940cae1423783edd966027 upstream.

The Intel desktop boards DH77EB and DH77DF have a hardware issue that
can be worked around by BIOS.  If the USB ports are switched to xHCI on
shutdown, the xHCI host will send a spurious interrupt, which will wake
the system.  Some BIOS will work around this, but not all.

The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.  The Intel Windows driver switches the ports back to EHCI, so
change the Linux xHCI driver to do the same.

Unfortunately, we can't tell the two effected boards apart from other
working motherboards, because the vendors will change the DMI strings
for the DH77EB and DH77DF boards to their own custom names.  One example
is Compulab's mini-desktop, the Intense-PC.  Instead, key off the
Panther Point xHCI host PCI vendor and device ID, and switch the ports
over for all PPT xHCI hosts.

The only impact this will have on non-effected boards is to add a couple
hundred milliseconds delay on boot when the BIOS has to switch the ports
over from EHCI to xHCI.

This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Denis Turischev <denis@compulab.co.il>
Tested-by: Denis Turischev <denis@compulab.co.il>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>