linux-stable.git/drivers/usb, branch v3.16.78

USB: cdc-wdm: fix race between write and disconnect due to flag abuse

2019-11-22T15:57:23+00:00

commit 1426bd2c9f7e3126e2678e7469dca9fd9fc6dd3e upstream.

In case of a disconnect an ongoing flush() has to be made fail.
Nevertheless we cannot be sure that any pending URB has already
finished, so although they will never succeed, they still must
not be touched.
The clean solution for this is to check for WDM_IN_USE
and WDM_DISCONNECTED in flush(). There is no point in ever
clearing WDM_IN_USE, as no further writes make sense.

The issue is as old as the driver.

Fixes: afba937e540c9 ("USB: CDC WDM driver")
Reported-by: syzbot+d232cca6ec42c2edb3fc@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum 
Link: https://lore.kernel.org/r/20190827103436.21143-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: storage: ums-realtek: Whitelist auto-delink support

2019-11-22T15:57:23+00:00

commit 1902a01e2bcc3abd7c9a18dc05e78c7ab4a53c54 upstream.

Auto-delink requires writing special registers to ums-realtek devices.
Unconditionally enable auto-delink may break newer devices.

So only enable auto-delink by default for the original three IDs,
0x0138, 0x0158 and 0x0159.

Realtek is working on a patch to properly support auto-delink for other
IDs.

BugLink: https://bugs.launchpad.net/bugs/1838886
Signed-off-by: Kai-Heng Feng 
Acked-by: Alan Stern 
Link: https://lore.kernel.org/r/20190827173450.13572-2-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: storage: ums-realtek: Update module parameter description for auto_delink_en

2019-11-22T15:57:23+00:00

commit f6445b6b2f2bb1745080af4a0926049e8bca2617 upstream.

The option named "auto_delink_en" is a bit misleading, as setting it to
false doesn't really disable auto-delink but let auto-delink be firmware
controlled.

Update the description to reflect the real usage of this parameter.

Signed-off-by: Kai-Heng Feng 
Link: https://lore.kernel.org/r/20190827173450.13572-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: host: ohci: fix a race condition between shutdown and irq

2019-11-22T15:57:22+00:00

commit a349b95d7ca0cea71be4a7dac29830703de7eb62 upstream.

This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.

[   34.851754] usb 2-1: USB disconnect, device number 2
[   35.166658] irq 156: nobody cared (try booting with the "irqpoll" option)
[   35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85
[   35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[   35.187886] Workqueue: usb_hub_wq hub_event
[   35.192063] Call trace:
[   35.194509]  dump_backtrace+0x0/0x150
[   35.198165]  show_stack+0x14/0x20
[   35.201475]  dump_stack+0xa0/0xc4
[   35.204785]  __report_bad_irq+0x34/0xe8
[   35.208614]  note_interrupt+0x2cc/0x318
[   35.212446]  handle_irq_event_percpu+0x5c/0x88
[   35.216883]  handle_irq_event+0x48/0x78
[   35.220712]  handle_fasteoi_irq+0xb4/0x188
[   35.224802]  generic_handle_irq+0x24/0x38
[   35.228804]  __handle_domain_irq+0x5c/0xb0
[   35.232893]  gic_handle_irq+0x58/0xa8
[   35.236548]  el1_irq+0xb8/0x180
[   35.239681]  __do_softirq+0x94/0x23c
[   35.243253]  irq_exit+0xd0/0xd8
[   35.246387]  __handle_domain_irq+0x60/0xb0
[   35.250475]  gic_handle_irq+0x58/0xa8
[   35.254130]  el1_irq+0xb8/0x180
[   35.257268]  kernfs_find_ns+0x5c/0x120
[   35.261010]  kernfs_find_and_get_ns+0x3c/0x60
[   35.265361]  sysfs_unmerge_group+0x20/0x68
[   35.269454]  dpm_sysfs_remove+0x2c/0x68
[   35.273284]  device_del+0x80/0x370
[   35.276683]  hid_destroy_device+0x28/0x60
[   35.280686]  usbhid_disconnect+0x4c/0x80
[   35.284602]  usb_unbind_interface+0x6c/0x268
[   35.288867]  device_release_driver_internal+0xe4/0x1b0
[   35.293998]  device_release_driver+0x14/0x20
[   35.298261]  bus_remove_device+0x110/0x128
[   35.302350]  device_del+0x148/0x370
[   35.305832]  usb_disable_device+0x8c/0x1d0
[   35.309921]  usb_disconnect+0xc8/0x2d0
[   35.313663]  hub_event+0x6e0/0x1128
[   35.317146]  process_one_work+0x1e0/0x320
[   35.321148]  worker_thread+0x40/0x450
[   35.324805]  kthread+0x124/0x128
[   35.328027]  ret_from_fork+0x10/0x18
[   35.331594] handlers:
[   35.333862] [<0000000079300c1d>] usb_hcd_irq
[   35.338126] [<0000000079300c1d>] usb_hcd_irq
[   35.342389] Disabling IRQ #156

ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
 ohci_irq()
  -> process_done_list()
   -> takeback_td()
    -> start_ed_unlink()

So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:

	/* interrupt for some other device? */
	if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
		return IRQ_NOTMINE;

To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().

This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.

Signed-off-by: Yoshihiro Shimoda 
Acked-by: Alan Stern 
Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.16:
 - Drop change in io_watchdog_func()
 - Adjust context]
Signed-off-by: Ben Hutchings

usb-storage: Add new JMS567 revision to unusual_devs

2019-11-22T15:57:18+00:00

commit 08d676d1685c2a29e4d0e1b0242324e564d4589e upstream.

Revision 0x0117 suffers from an identical issue to earlier revisions,
therefore it should be added to the quirks list.

Signed-off-by: Henk van der Laan 
Link: https://lore.kernel.org/r/20190816200847.21366-1-opensource@henkvdlaan.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: cdc-acm: make sure a refcount is taken early enough

2019-11-22T15:57:17+00:00

commit c52873e5a1ef72f845526d9f6a50704433f9c625 upstream.

destroy() will decrement the refcount on the interface, so that
it needs to be taken so early that it never undercounts.

Fixes: 7fb57a019f94e ("USB: cdc-acm: Fix potential deadlock (lockdep warning)")
Reported-and-tested-by: syzbot+1b2449b7b5dc240d107a@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum 
Link: https://lore.kernel.org/r/20190808142119.7998-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: serial: option: Add Motorola modem UARTs

2019-11-22T15:57:16+00:00

commit 6caf0be40a707689e8ff8824fdb96ef77685b1ba upstream.

On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams .

As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold .

The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork .

However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.

The ttyUSB ports on Droid 4 are:

ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable

The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.

To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.

The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.

The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.

The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.

Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.

I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.

After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=22b8 ProdID=2a70 Rev= 0.00
S:  Manufacturer=Motorola, Incorporated
S:  Product=Flash MZ600
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=86(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=88(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=8b(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=8c(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=08(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E:  Ad=8d(I) Atr=03(Int.) MxPS=  64 Ivl=5ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=09(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

In 22b8:900e "qc_dload" mode the device shows up as:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=22b8 ProdID=900e Rev= 0.00
S:  Manufacturer=Motorola, Incorporated
S:  Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

And in 22b8:4281 "ram_downloader" mode the device shows up as:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=22b8 ProdID=4281 Rev= 0.00
S:  Manufacturer=Motorola, Incorporated
S:  Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

Cc: Bjørn Mork 
Cc: Dan Williams 
Cc: Lars Melin 
Cc: Marcel Partap 
Cc: Merlijn Wajer 
Cc: Michael Scott 
Cc: NeKit 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Tested-by: Pavel Machek 
Signed-off-by: Tony Lindgren 
Signed-off-by: Johan Hovold 
Signed-off-by: Ben Hutchings

USB: core: Fix races in character device registration and deregistraion

2019-11-22T15:57:15+00:00

commit 303911cfc5b95d33687d9046133ff184cf5043ff upstream.

The syzbot fuzzer has found two (!) races in the USB character device
registration and deregistration routines.  This patch fixes the races.

The first race results from the fact that usb_deregister_dev() sets
usb_minors[intf->minor] to NULL before calling device_destroy() on the
class device.  This leaves a window during which another thread can
allocate the same minor number but will encounter a duplicate name
error when it tries to register its own class device.  A typical error
message in the system log would look like:

    sysfs: cannot create duplicate filename '/class/usbmisc/ldusb0'

The patch fixes this race by destroying the class device first.

The second race is in usb_register_dev().  When that routine runs, it
first allocates a minor number, then drops minor_rwsem, and then
creates the class device.  If the device creation fails, the minor
number is deallocated and the whole routine returns an error.  But
during the time while minor_rwsem was dropped, there is a window in
which the minor number is allocated and so another thread can
successfully open the device file.  Typically this results in
use-after-free errors or invalid accesses when the other thread closes
its open file reference, because the kernel then tries to release
resources that were already deallocated when usb_register_dev()
failed.  The patch fixes this race by keeping minor_rwsem locked
throughout the entire routine.

Reported-and-tested-by: syzbot+30cf45ebfe0b0c4847a1@syzkaller.appspotmail.com
Signed-off-by: Alan Stern 
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908121607590.1659-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: yurex: Fix use-after-free in yurex_delete

2019-11-22T15:57:12+00:00

commit fc05481b2fcabaaeccf63e32ac1baab54e5b6963 upstream.

syzbot reported the following crash [0]:

BUG: KASAN: use-after-free in usb_free_coherent+0x79/0x80
drivers/usb/core/usb.c:928
Read of size 8 at addr ffff8881b18599c8 by task syz-executor.4/16007

CPU: 0 PID: 16007 Comm: syz-executor.4 Not tainted 5.3.0-rc2+ #23
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0xca/0x13e lib/dump_stack.c:113
  print_address_description+0x6a/0x32c mm/kasan/report.c:351
  __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482
  kasan_report+0xe/0x12 mm/kasan/common.c:612
  usb_free_coherent+0x79/0x80 drivers/usb/core/usb.c:928
  yurex_delete+0x138/0x330 drivers/usb/misc/yurex.c:100
  kref_put include/linux/kref.h:65 [inline]
  yurex_release+0x66/0x90 drivers/usb/misc/yurex.c:392
  __fput+0x2d7/0x840 fs/file_table.c:280
  task_work_run+0x13f/0x1c0 kernel/task_work.c:113
  tracehook_notify_resume include/linux/tracehook.h:188 [inline]
  exit_to_usermode_loop+0x1d2/0x200 arch/x86/entry/common.c:163
  prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
  syscall_return_slowpath arch/x86/entry/common.c:274 [inline]
  do_syscall_64+0x45f/0x580 arch/x86/entry/common.c:299
  entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x413511
Code: 75 14 b8 03 00 00 00 0f 05 48 3d 01 f0 ff ff 0f 83 04 1b 00 00 c3 48
83 ec 08 e8 0a fc ff ff 48 89 04 24 b8 03 00 00 00 0f 05 <48> 8b 3c 24 48
89 c2 e8 53 fc ff ff 48 89 d0 48 83 c4 08 48 3d 01
RSP: 002b:00007ffc424ea2e0 EFLAGS: 00000293 ORIG_RAX: 0000000000000003
RAX: 0000000000000000 RBX: 0000000000000007 RCX: 0000000000413511
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000006
RBP: 0000000000000001 R08: 0000000029a2fc22 R09: 0000000029a2fc26
R10: 00007ffc424ea3c0 R11: 0000000000000293 R12: 000000000075c9a0
R13: 000000000075c9a0 R14: 0000000000761938 R15: ffffffffffffffff

Allocated by task 2776:
  save_stack+0x1b/0x80 mm/kasan/common.c:69
  set_track mm/kasan/common.c:77 [inline]
  __kasan_kmalloc mm/kasan/common.c:487 [inline]
  __kasan_kmalloc.constprop.0+0xbf/0xd0 mm/kasan/common.c:460
  kmalloc include/linux/slab.h:552 [inline]
  kzalloc include/linux/slab.h:748 [inline]
  usb_alloc_dev+0x51/0xf95 drivers/usb/core/usb.c:583
  hub_port_connect drivers/usb/core/hub.c:5004 [inline]
  hub_port_connect_change drivers/usb/core/hub.c:5213 [inline]
  port_event drivers/usb/core/hub.c:5359 [inline]
  hub_event+0x15c0/0x3640 drivers/usb/core/hub.c:5441
  process_one_work+0x92b/0x1530 kernel/workqueue.c:2269
  worker_thread+0x96/0xe20 kernel/workqueue.c:2415
  kthread+0x318/0x420 kernel/kthread.c:255
  ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352

Freed by task 16007:
  save_stack+0x1b/0x80 mm/kasan/common.c:69
  set_track mm/kasan/common.c:77 [inline]
  __kasan_slab_free+0x130/0x180 mm/kasan/common.c:449
  slab_free_hook mm/slub.c:1423 [inline]
  slab_free_freelist_hook mm/slub.c:1470 [inline]
  slab_free mm/slub.c:3012 [inline]
  kfree+0xe4/0x2f0 mm/slub.c:3953
  device_release+0x71/0x200 drivers/base/core.c:1064
  kobject_cleanup lib/kobject.c:693 [inline]
  kobject_release lib/kobject.c:722 [inline]
  kref_put include/linux/kref.h:65 [inline]
  kobject_put+0x171/0x280 lib/kobject.c:739
  put_device+0x1b/0x30 drivers/base/core.c:2213
  usb_put_dev+0x1f/0x30 drivers/usb/core/usb.c:725
  yurex_delete+0x40/0x330 drivers/usb/misc/yurex.c:95
  kref_put include/linux/kref.h:65 [inline]
  yurex_release+0x66/0x90 drivers/usb/misc/yurex.c:392
  __fput+0x2d7/0x840 fs/file_table.c:280
  task_work_run+0x13f/0x1c0 kernel/task_work.c:113
  tracehook_notify_resume include/linux/tracehook.h:188 [inline]
  exit_to_usermode_loop+0x1d2/0x200 arch/x86/entry/common.c:163
  prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
  syscall_return_slowpath arch/x86/entry/common.c:274 [inline]
  do_syscall_64+0x45f/0x580 arch/x86/entry/common.c:299
  entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff8881b1859980
  which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 72 bytes inside of
  2048-byte region [ffff8881b1859980, ffff8881b185a180)
The buggy address belongs to the page:
page:ffffea0006c61600 refcount:1 mapcount:0 mapping:ffff8881da00c000
index:0x0 compound_mapcount: 0
flags: 0x200000000010200(slab|head)
raw: 0200000000010200 0000000000000000 0000000100000001 ffff8881da00c000
raw: 0000000000000000 00000000000f000f 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
  ffff8881b1859880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
  ffff8881b1859900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> ffff8881b1859980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                                               ^
  ffff8881b1859a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
  ffff8881b1859a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================

A quick look at the yurex_delete() shows that we drop the reference
to the usb_device before releasing any buffers associated with the
device. Delay the reference drop until we have finished the cleanup.

[0] https://lore.kernel.org/lkml/0000000000003f86d8058f0bd671@google.com/

Fixes: 6bc235a2e24a5e ("USB: add driver for Meywa-Denki & Kayac YUREX")
Cc: Jiri Kosina 
Cc: Tomoki Sekiyama 
Cc: Oliver Neukum 
Cc: andreyknvl@google.com
Cc: gregkh@linuxfoundation.org
Cc: Alan Stern 
Cc: syzkaller-bugs@googlegroups.com
Cc: dtor@chromium.org
Reported-by: syzbot+d1fedb1c1fdb07fca507@syzkaller.appspotmail.com
Signed-off-by: Suzuki K Poulose 
Link: https://lore.kernel.org/r/20190805111528.6758-1-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: serial: option: Add support for ZTE MF871A

2019-11-22T15:57:12+00:00

commit 7e7ae38bf928c5cfa6dd6e9a2cf8b42c84a27c92 upstream.

This patch adds support for MF871A USB modem (aka Speed USB STICK U03)
to option driver. This modem is manufactured by ZTE corporation, and
sold by KDDI.

Interface layout:
0: AT
1: MODEM

usb-devices output:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  9 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=1481 Rev=52.87
S:  Manufacturer=ZTE,Incorporated
S:  Product=ZTE Technologies MSM
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option

Co-developed-by: Hiroyuki Yamamoto 
Signed-off-by: Hiroyuki Yamamoto 
Signed-off-by: Yoshiaki Okamoto 
Signed-off-by: Johan Hovold 
Signed-off-by: Ben Hutchings