linux-stable.git/drivers/usb, branch v3.16.64 Linux kernel stable tree xhci: Don't prevent USB2 bus suspend in state check intended for USB3 only 2019-02-11T17:54:26+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2018-12-14T08:54:43+00:00 c6ebef26a95834d86a9e72fa70f5fd4b6ec395bf commit 45f750c16cae3625014c14c77bd9005eda975d35 upstream. The code to prevent a bus suspend if a USB3 port was still in link training also reacted to USB2 port polling state. This caused bus suspend to busyloop in some cases. USB2 polling state is different from USB3, and should not prevent bus suspend. Limit the USB3 link training state check to USB3 root hub ports only. The origial commit went to stable so this need to be applied there as well Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 45f750c16cae3625014c14c77bd9005eda975d35 upstream.

The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.

Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well

Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: serial: option: add Simcom SIM7500/SIM7600 (MBIM mode) 2019-02-11T17:54:25+00:00 Jörgen Storvist jorgen.storvist@gmail.com 2018-12-12T07:39:39+00:00 d75d90b57d06fb4b04240b3da8fcbd2ad4a64907 commit cc6730df08a291e51e145bc65e24ffb5e2f17ab6 upstream. Added USB serial option driver support for Simcom SIM7500/SIM7600 series cellular modules exposing MBIM interface (VID 0x1e0e,PID 0x9003) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 14 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9003 Rev=03.18 S: Manufacturer=SimTech, Incorporated S: Product=SimTech, Incorporated S: SerialNumber=0123456789ABCDEF C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 6 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> [bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit cc6730df08a291e51e145bc65e24ffb5e2f17ab6 upstream.

Added USB serial option driver support for Simcom SIM7500/SIM7600 series
cellular modules exposing MBIM interface (VID 0x1e0e,PID 0x9003)

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 14 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1e0e ProdID=9003 Rev=03.18
S:  Manufacturer=SimTech, Incorporated
S:  Product=SimTech, Incorporated
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 6 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim

Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: serial: option: add HP lt4132 2019-02-11T17:54:23+00:00 Tore Anderson tore@fud.no 2018-12-08T18:05:12+00:00 dc1f560d5f20861dc8495fca374f9f091cf77f6e commit d57ec3c83b5153217a70b561d4fb6ed96f2f7a25 upstream. The HP lt4132 is a rebranded Huawei ME906s-158 LTE modem. The interface with protocol 0x16 is "CDC ECM & NCM" according to the *.inf files included with the Windows driver. Attaching the option driver to it doesn't result in a /dev/ttyUSB* device being created, so I've excluded it. Note that it is also excluded for corresponding Huawei-branded devices, cf. commit d544db293a44 ("USB: support new huawei devices in option.c"). T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=06 Prot=16 Driver=(none) I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option I: If#=0x6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 3 Cfg#= 3 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option Signed-off-by: Tore Anderson <tore@fud.no> [ johan: drop id defines ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit d57ec3c83b5153217a70b561d4fb6ed96f2f7a25 upstream.

The HP lt4132 is a rebranded Huawei ME906s-158 LTE modem.

The interface with protocol 0x16 is "CDC ECM & NCM" according to the *.inf
files included with the Windows driver. Attaching the option driver to it
doesn't result in a /dev/ttyUSB* device being created, so I've excluded it.
Note that it is also excluded for corresponding Huawei-branded devices, cf.
commit d544db293a44 ("USB: support new huawei devices in option.c").

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs=  3
P:  Vendor=03f0 ProdID=a31d Rev=01.02
S:  Manufacturer=HP Inc.
S:  Product=HP lt4132 LTE/HSPA+ 4G Module
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=2mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option
I:  If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=06 Prot=16 Driver=(none)
I:  If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs=  3
P:  Vendor=03f0 ProdID=a31d Rev=01.02
S:  Manufacturer=HP Inc.
S:  Product=HP lt4132 LTE/HSPA+ 4G Module
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=2mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=cdc_ether
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option
I:  If#=0x6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs=  3
P:  Vendor=03f0 ProdID=a31d Rev=01.02
S:  Manufacturer=HP Inc.
S:  Product=HP lt4132 LTE/HSPA+ 4G Module
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 3 Cfg#= 3 Atr=a0 MxPwr=2mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option

Signed-off-by: Tore Anderson <tore@fud.no>
[ johan: drop id defines ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: Prevent U1/U2 link pm states if exit latency is too long 2019-02-11T17:54:21+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2018-12-05T12:22:39+00:00 7e2344d2f1e9a91f8baa84d62a32ea442f87d8c6 commit 0472bf06c6fd33c1a18aaead4c8f91e5a03d8d7b upstream. Don't allow USB3 U1 or U2 if the latency to wake up from the U-state reaches the service interval for a periodic endpoint. This is according to xhci 1.1 specification section 4.23.5.2 extra note: "Software shall ensure that a device is prevented from entering a U-state where its worst case exit latency approaches the ESIT." Allowing too long exit latencies for periodic endpoint confuses xHC internal scheduling, and new devices may fail to enumerate with a "Not enough bandwidth for new device state" error from the host. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: adjust context, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 0472bf06c6fd33c1a18aaead4c8f91e5a03d8d7b upstream.

Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.

This is according to xhci 1.1 specification section 4.23.5.2 extra note:

"Software shall ensure that a device is prevented from entering a U-state
 where its worst case exit latency approaches the ESIT."

Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: workaround CSS timeout on AMD SNPS 3.0 xHC 2019-02-11T17:54:21+00:00 Sandeep Singh sandeep.singh@amd.com 2018-12-05T12:22:38+00:00 f6b0a0659bdaa814ca0ed5c433cb26e417260408 commit a7d57abcc8a5bdeb53bbf8e87558e8e0a2c2a29d upstream. Occasionally AMD SNPS 3.0 xHC does not respond to CSS when set, also it does not flag anything on SRE and HCE to point the internal xHC errors on USBSTS register. This stalls the entire system wide suspend and there is no point in stalling just because of xHC CSS is not responding. To work around this problem, if the xHC does not flag anything on SRE and HCE, we can skip the CSS timeout and allow the system to continue the suspend. Once the system resume happens we can internally reset the controller using XHCI_RESET_ON_RESUME quirk Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com> cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: - Use next available quirk bit - Fold in commit 2419f30a4a4f "USB: xhci: fix 'broken_suspend' placement ..." - Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit a7d57abcc8a5bdeb53bbf8e87558e8e0a2c2a29d upstream.

Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.

To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk

Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
 - Use next available quirk bit
 - Fold in commit 2419f30a4a4f "USB: xhci: fix 'broken_suspend' placement ..."
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: check usb_get_extra_descriptor for proper size 2019-02-11T17:54:20+00:00 Mathias Payer mathias.payer@nebelwelt.net 2018-12-05T20:19:59+00:00 f8860a91d7538022c1c3f0bdddeec9a9d83e0c09 commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream. When reading an extra descriptor, we need to properly check the minimum and maximum size allowed, to prevent from invalid data being sent by a device. Reported-by: Hui Peng <benquike@gmail.com> Reported-by: Mathias Payer <mathias.payer@nebelwelt.net> Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Hui Peng <benquike@gmail.com> Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream.

When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.

Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device 2019-02-11T17:54:20+00:00 Harry Pan harry.pan@intel.com 2018-11-28T16:40:41+00:00 37c3fc2e49bf95a57d46fb8c56a9d8bd723c35c3 commit 2f2dde6ba89b1ef1fe23c1138131b315d9aa4019 upstream. Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is in 0781:5591, will aggressively request LPM of U1/U2 during runtime, when using this thumb drive as the OS installation key we found the device will generate failure during U1 exit path making it dropped from the USB bus, this causes a corrupted installation in system at the end. i.e., [ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004 [ 166.918327] usb usb2-port2: link state change [ 166.918337] usb usb2-port2: do warm reset [ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms [ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms [ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s [ 167.276050] usb 2-2: USB disconnect, device number 2 [ 167.276058] usb 2-2: unregistering device [ 167.276060] usb 2-2: unregistering interface 2-2:1.0 [ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk [ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00 ... Analyzed the USB trace in the link layer we realized it is because of the 6-ms timer of tRecoveryConfigurationTimeout which documented on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from Recovery.Configuration"; device initiates U1 exit -> Recovery.Active -> Recovery.Configuration, then the host timer timeout makes the link transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset. Interestingly, the other higher volume of SanDisk Ultra Flair sharing the same VID:PID, such as 64GB, would not request LPM during runtime, it sticks at U0 always, thus disabling LPM does not affect those thumb drives at all. The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583. Signed-off-by: Harry Pan <harry.pan@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 2f2dde6ba89b1ef1fe23c1138131b315d9aa4019 upstream.

Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.

i.e.,
[  166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[  166.918327] usb usb2-port2: link state change
[  166.918337] usb usb2-port2: do warm reset
[  166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[  167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[  167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[  167.276050] usb 2-2: USB disconnect, device number 2
[  167.276058] usb 2-2: unregistering device
[  167.276060] usb 2-2: unregistering interface 2-2:1.0
[  167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[  167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[  167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...

Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.

Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.

The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.

Signed-off-by: Harry Pan <harry.pan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: appledisplay: Add 27" Apple Cinema Display 2019-02-11T17:54:19+00:00 Alexander Theissen alex.theissen@me.com 2018-12-04T22:43:35+00:00 ab0b0f367e2160fcaa19282b53a8aeb7215d0622 commit d7859905301880ad3e16272399d26900af3ac496 upstream. Add another Apple Cinema Display to the list of supported displays. Signed-off-by: Alexander Theissen <alex.theissen@me.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit d7859905301880ad3e16272399d26900af3ac496 upstream.

Add another Apple Cinema Display to the list of supported displays.

Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: core: quirks: add RESET_RESUME quirk for Cherry G230 Stream series 2019-02-11T17:54:12+00:00 Michael Niewöhner linux@mniewoehner.de 2018-11-25T16:57:33+00:00 172a6767172f66a67b72441121e7c235a2692f02 commit effd14f66cc1ef6701a19c5a56e39c35f4d395a5 upstream. Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to function correctly. This fixes a but where double pressing numlock locks up the device completely with need to replug the keyboard. Signed-off-by: Michael Niewöhner <linux@mniewoehner.de> Tested-by: Michael Niewöhner <linux@mniewoehner.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit effd14f66cc1ef6701a19c5a56e39c35f4d395a5 upstream.

Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to
function correctly. This fixes a but where double pressing numlock locks
up the device completely with need to replug the keyboard.

Signed-off-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: usb-storage: Add new IDs to ums-realtek 2019-02-11T17:54:12+00:00 Kai-Heng Feng kai.heng.feng@canonical.com 2018-11-23T08:42:19+00:00 d27557e5b09f4400e037f1104f5ac324894d71da commit a84a1bcc992f0545a51d2e120b8ca2ef20e2ea97 upstream. There are two new Realtek card readers require ums-realtek to work correctly. Add the new IDs to support them. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit a84a1bcc992f0545a51d2e120b8ca2ef20e2ea97 upstream.

There are two new Realtek card readers require ums-realtek to work
correctly.

Add the new IDs to support them.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>