linux-stable.git/drivers/usb, branch v3.13.6

USB: ftdi_sio: add Cressi Leonardo PID

2014-03-07T06:06:24+00:00

commit 6dbd46c849e071e6afc1e0cad489b0175bca9318 upstream.

Hello,

the following patch adds an entry for the PID of a Cressi Leonardo
diving computer interface to kernel 3.13.0.
It is detected as FT232RL.
Works with subsurface.

Signed-off-by: Joerg Dorchain 
Signed-off-by: Greg Kroah-Hartman

usb: ehci: fix deadlock when threadirqs option is used

2014-03-07T06:06:24+00:00

commit a1227f3c1030e96ebc51d677d2f636268845c5fb upstream.

ehci_irq() and ehci_hrtimer_func() can deadlock on ehci->lock when
threadirqs option is used. To prevent the deadlock use
spin_lock_irqsave() in ehci_irq().

This change can be reverted when hrtimer callbacks become threaded.

Signed-off-by: Stanislaw Gruszka 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: EHCI: add delay during suspend to prevent erroneous wakeups

2014-03-07T06:06:24+00:00

commit 3e8d6d85adedc59115a564c0a54b36e42087c4d9 upstream.

High-speed USB connections revert back to full-speed signalling when
the device goes into suspend.  This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.

On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state.  It generates a false wakeup signal,
which can prevent the controller from going to sleep.

To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling.  (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)

Signed-off-by: Alan Stern 
Reviewed-by: Peter Chen 
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: blacklist interface 4 for Cinterion PHS8 and PXS8

2014-03-07T06:06:24+00:00

commit 12df84d4a80278a5b1abfec3206795291da52fc9 upstream.

This interface is to be handled by the qmi_wwan driver.

CC: Hans-Christoph Schemmel 
CC: Christian Schmiedl 
CC: Nicolaus Colberg 
CC: David McCullough 
Signed-off-by: Aleksander Morgado 
Signed-off-by: Greg Kroah-Hartman

usb: gadget: bcm63xx_udc: fix build failure on DMA channel code

2014-03-07T06:06:24+00:00

commit 2d1f7af3d60dd09794e0738a915d272c6c27abc5 upstream.

Commit 3dc6475 ("bcm63xx_enet: add support Broadcom BCM6345 Ethernet")
changed the ENETDMA[CS] macros such that they are no longer macros, but
actual register offset definitions. The bcm63xx_udc driver was not
updated, and as a result, causes the following build error to pop up:

 CC      drivers/usb/gadget/u_ether.o
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_write':
drivers/usb/gadget/bcm63xx_udc.c:642:24: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_reset_channel':
drivers/usb/gadget/bcm63xx_udc.c:698:46: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c:700:49: error: called object '0' is not
a function

Fix this by updating usb_dmac_{read,write}l and usb_dmas_{read,write}l to
take an extra channel argument, and use the channel width
(ENETDMA_CHAN_WIDTH) to offset the register we want to access, hence
doing again what the macro implicitely did for us.

Cc: Kevin Cernekee 
Cc: Jonas Gorski 
Signed-off-by: Florian Fainelli 
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

usb: chipidea: need to mask when writting endptflush and endptprime

2014-03-07T06:06:24+00:00

commit 5bf5dbeda2454296f1984adfbfc8e6f5965ac389 upstream.

ENDPTFLUSH and ENDPTPRIME registers are set by software and clear
by hardware. There is a bit for each endpoint. When we are setting
a bit for an endpoint we should make sure we do not touch other
endpoint bit. There is a race condition if the hardware clear the
bit between the read and the write in hw_write.

Signed-off-by: Peter Chen 
Signed-off-by: Matthieu CASTET 
Tested-by: Michael Grzeschik 
Signed-off-by: Greg Kroah-Hartman

Revert "usbcore: set lpm_capable field for LPM capable root hubs"

2014-02-22T21:34:56+00:00

commit 140e3026a57ab7d830dab2f2c57796c222db0ea9 upstream.

Commit 9df89d85b407690afa46ddfbccc80bec6869971d "usbcore: set
lpm_capable field for LPM capable root hubs" was created under the
assumption that all USB host controllers should have USB 3.0 Link PM
enabled for all devices under the hosts.

Unfortunately, that's not the case.  The xHCI driver relies on knowledge
of the host hardware scheduler to calculate the LPM U1/U2 timeout
values, and it only sets lpm_capable to one for Intel host controllers
(that have the XHCI_LPM_SUPPORT quirk set).

When LPM is enabled for some Fresco Logic hosts, it causes failures with
a AgeStar 3UBT USB 3.0 hard drive dock:

Jan 11 13:59:03 sg-laptop kernel: usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:03 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:08 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:08 sg-laptop kernel: usb-storage 3-1:1.0: USB Mass Storage device detected
Jan 11 13:59:08 sg-laptop mtp-probe[613]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1c.3/0000:04:00.0/usb3/3-1"
Jan 11 13:59:08 sg-laptop mtp-probe[613]: bus: 3, device: 2 was not an MTP device
Jan 11 13:59:08 sg-laptop kernel: scsi6 : usb-storage 3-1:1.0
Jan 11 13:59:13 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:18 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:18 sg-laptop kernel: usbcore: registered new interface driver usb-storage
Jan 11 13:59:40 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: device descriptor read/8, error -71
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: device descriptor read/8, error -110
Jan 11 13:59:46 sg-laptop kernel: scsi 6:0:0:0: Device offlined - not ready after error recovery
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: USB disconnect, device number 2

lspci for the affected host:

04:00.0 0c03: 1b73:1000 (rev 04) (prog-if 30 [XHCI])
        Subsystem: 1043:1039
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 
Reported-by: Sergey Galanov 
Signed-off-by: Greg Kroah-Hartman

Revert "usb: xhci: Link TRB must not occur within a USB payload burst"

2014-02-22T21:34:56+00:00

commit 3d4b81eda2211f32886e2978daf6f39885042fc4 upstream.

This reverts commit 35773dac5f862cb1c82ea151eba3e2f6de51ec3e.  It's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb.  Commit 70cabb7d992f "xhci 1.0: Limit
arbitrarily-aligned scatter gather." should fix the issues seen with the
ax88179_178a driver on xHCI 1.0 hosts, without causing regressions.

Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

Revert "xhci: Avoid infinite loop when sg urb requires too many trbs"

2014-02-22T21:34:56+00:00

commit 9cf00d91708221ff2d8a11143315f7ebab8d5da8 upstream.

This reverts commit d6c9ea9069af684358efedcaf2f2f687f51c58ee.

We are ripping out commit 35773dac5f862cb1c82ea151eba3e2f6de51ec3e "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb.  This commit attempted to fix the
issues with that patch.

Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

Revert "xhci: Set scatter-gather limit to avoid failed block writes."

2014-02-22T21:34:55+00:00

commit 1386ff75797a187df324062fb4e929152392da88 upstream.

This reverts commit f2d9b991c549f159dc9ae81f77d8206c790cbfee.

We are ripping out commit 35773dac5f862cb1c82ea151eba3e2f6de51ec3e "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb.  This commit attempted to fix the
issues with that patch.

Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman