linux-stable.git/drivers/usb, branch v3.12.6 Linux kernel stable tree USB: option: support new huawei devices 2013-12-20T15:48:56+00:00 Fangxiaozhi (Franko) fangxiaozhi@huawei.com 2013-12-02T09:00:11+00:00 9d93dae88cedd47e58f4e34126420a80a521998d commit 2bf308d7bc5e8cdd69672199f59532f35339133c upstream. Add new supporting declarations to option.c, to support Huawei new devices with new bInterfaceProtocol value. Signed-off-by: fangxiaozhi <huananhu@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2bf308d7bc5e8cdd69672199f59532f35339133c upstream.

Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceProtocol value.

Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: option: blacklist interface 1 for Huawei E173s-6 2013-12-20T15:48:55+00:00 Gustavo Zacarias gustavo@zacarias.com.ar 2013-11-11T12:59:15+00:00 588cd6b701fed893d55a5aec76b06fa2aa445147 commit 8f173e22abf2258ddfa73f46eadbb6a6c29f1631 upstream. Interface 1 on this device isn't for option to bind to otherwise an oops on usb_wwan with log flooding will happen when accessing the port: tty_release: ttyUSB1: read/write wait queue active! It doesn't seem to respond to QMI if it's added to qmi_wwan so don't add it there - it's likely used by the card reader. Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 8f173e22abf2258ddfa73f46eadbb6a6c29f1631 upstream.

Interface 1 on this device isn't for option to bind to otherwise an oops
on usb_wwan with log flooding will happen when accessing the port:

tty_release: ttyUSB1: read/write wait queue active!

It doesn't seem to respond to QMI if it's added to qmi_wwan so don't add
it there - it's likely used by the card reader.

Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt 2013-12-20T15:48:55+00:00 Sebastian Andrzej Siewior bigeasy@linutronix.de 2013-11-12T15:37:47+00:00 5227e3f59f34958e666308334fd83b7966fcb950 commit a655f481d83d6d37bec0a2ddfdd24c30ff8f541f upstream. The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a655f481d83d6d37bec0a2ddfdd24c30ff8f541f upstream.

The TX-complete interrupt of the CPPI41 on AM335x fires too early.
Adding a loop and counting how long it takes until the
MUSB_TXCSR_TXPKTRDY bit is cleared I see
FS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1
|cppi41_dma_callback() 74 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1
|cppi41_dma_callback() 66 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops

avg: 110 - 150us

HS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1
|cppi41_dma_callback() 0 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1
|cppi41_dma_callback() 2 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1
|cppi41_dma_callback() 13 loops

avg: 2us

for the same test case. One loop means a udelay(1). The delay seems to
depend on the packet size. On HS the bit is always cleared for small
packet sizes while on FS it is never the case, it mostly around 110us.
This testing has been performed with g_ether (musb as device) and using BULK
transfers.

INTR transfers are way more fun: during init the gadget sends a INT
packet to the host and cppi41 says "transfer done" shortly after. The
MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host
did not try to receive it, it does so after the interface (on host side) has
been configured. Until this happens, that packet remains in musb's FIFO.

To fix this, two things are done:
- No DMA transfers for INT based endpoints. These transfer are usually
  very small and rare so it is likely better to skip the DMA engine and
  stuff the four bytes directly into the FIFO
- on HS we poll up to 25us and hope that bit goes away. If not we setup
  a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS
  the command
  | ping 10.10.10.10 -c1 -s65130
  creates about 44 1514bytes transfers. About 19 of them need a second
  timer to complete.

Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: musb: musb_cppi41: factor most of cppi41_dma_callback() into cppi41_trans_done() 2013-12-20T15:48:55+00:00 Sebastian Andrzej Siewior bigeasy@linutronix.de 2013-11-12T15:37:46+00:00 b5f4d64674beb372148365dee51bba99728505e5 commit d373a8534d5e1e7a350e40d3c11961a7cd8d530b upstream. This patch moves most of the logic in cppi41_dma_callback() into cppi41_trans_done() where it can be called from another function. Instead of computing "transferred" (the number of bytes transferred in the last transaction) in cppi41_trans_done() the member "cppi41_channel->prog_len" is now set to 0 if the transfer as a whole can be considered as done. If it is != 0 then the next iteration is assumed. This is a preparation for a workaround. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit d373a8534d5e1e7a350e40d3c11961a7cd8d530b upstream.

This patch moves most of the logic in cppi41_dma_callback() into
cppi41_trans_done() where it can be called from another function.
Instead of computing "transferred" (the number of bytes transferred in
the last transaction) in cppi41_trans_done() the member
"cppi41_channel->prog_len" is now set to 0 if the transfer as a whole
can be considered as done. If it is != 0 then the next iteration is
assumed.
This is a preparation for a workaround.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: xhci: Link TRB must not occur within a USB payload burst 2013-12-20T15:48:55+00:00 David Laight David.Laight@ACULAB.COM 2013-11-11T12:26:54+00:00 459d3c14611784bc5155cc622536b2b0f0740aa2 commit 35773dac5f862cb1c82ea151eba3e2f6de51ec3e upstream. Section 4.11.7.1 of rev 1.0 of the xhci specification states that a link TRB can only occur at a boundary between underlying USB frames (512 bytes for high speed devices). If this isn't done the USB frames aren't formatted correctly and, for example, the USB3 ethernet ax88179_178a card will stop sending (while still receiving) when running a netperf tcp transmit test with (say) and 8k buffer. This should be a candidate for stable, the ax88179_178a driver defaults to gso and tso enabled so it passes a lot of fragmented skb to the USB stack. Notes from Sarah: Discussion: http://marc.info/?l=linux-usb&m=138384509604981&w=2 This patch fixes a long-standing xHCI driver bug that was revealed by a change in 3.12 in the usb-net driver. Commit 638c5115a794981441246fa8fa5d95c1875af5ba "USBNET: support DMA SG" added support to use bulk endpoint scatter-gather (urb->sg). Only the USB ethernet drivers trigger this bug, because the mass storage driver sends sg list entries in page-sized chunks. This patch only fixes the issue for bulk endpoint scatter-gather. The problem will still occur for periodic endpoints, because hosts will interpret no-op transfers as a request to skip a service interval, which is not what we want. Luckily, the USB core isn't set up for scatter-gather on isochronous endpoints, and no USB drivers use scatter-gather for interrupt endpoints. Document this known limitation so that developers won't try to use urb->sg for interrupt endpoints until this issue is fixed. The more comprehensive fix would be to allow link TRBs in the middle of the endpoint ring and revert this patch, but that fix would touch too much code to be allowed in for stable. This patch should be backported to kernels as old as 3.12, that contain the commit 638c5115a794981441246fa8fa5d95c1875af5ba "USBNET: support DMA SG". Without this patch, the USB network device gets wedged, and stops sending packets. Mark Lord confirms this patch fixes the regression: http://marc.info/?l=linux-netdev&m=138487107625966&w=2 Signed-off-by: David Laight <david.laight@aculab.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Mark Lord <mlord@pobox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 35773dac5f862cb1c82ea151eba3e2f6de51ec3e upstream.

Section 4.11.7.1 of rev 1.0 of the xhci specification states that a link TRB
can only occur at a boundary between underlying USB frames (512 bytes for
high speed devices).

If this isn't done the USB frames aren't formatted correctly and, for example,
the USB3 ethernet ax88179_178a card will stop sending (while still receiving)
when running a netperf tcp transmit test with (say) and 8k buffer.

This should be a candidate for stable, the ax88179_178a driver defaults to
gso and tso enabled so it passes a lot of fragmented skb to the USB stack.

Notes from Sarah:

Discussion: http://marc.info/?l=linux-usb&m=138384509604981&w=2

This patch fixes a long-standing xHCI driver bug that was revealed by a
change in 3.12 in the usb-net driver.  Commit
638c5115a794981441246fa8fa5d95c1875af5ba "USBNET: support DMA SG" added
support to use bulk endpoint scatter-gather (urb->sg).  Only the USB
ethernet drivers trigger this bug, because the mass storage driver sends
sg list entries in page-sized chunks.

This patch only fixes the issue for bulk endpoint scatter-gather.  The
problem will still occur for periodic endpoints, because hosts will
interpret no-op transfers as a request to skip a service interval, which
is not what we want.

Luckily, the USB core isn't set up for scatter-gather on isochronous
endpoints, and no USB drivers use scatter-gather for interrupt
endpoints.  Document this known limitation so that developers won't try
to use urb->sg for interrupt endpoints until this issue is fixed.  The
more comprehensive fix would be to allow link TRBs in the middle of the
endpoint ring and revert this patch, but that fix would touch too much
code to be allowed in for stable.

This patch should be backported to kernels as old as 3.12, that contain
the commit 638c5115a794981441246fa8fa5d95c1875af5ba "USBNET: support DMA
SG".  Without this patch, the USB network device gets wedged, and stops
sending packets.  Mark Lord confirms this patch fixes the regression:

http://marc.info/?l=linux-netdev&m=138487107625966&w=2

Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: gadget: composite: reset delayed_status on reset_config 2013-12-20T15:48:55+00:00 Michael Grzeschik m.grzeschik@pengutronix.de 2013-11-11T22:43:32+00:00 68c4e50ee15f1095be85ff2c670ed005a26c51c5 commit 2bac51a1827a18821150ed8c9f9752c02f9c2b02 upstream. The delayed_status value is used to keep track of status response packets on ep0. It needs to be reset or the set_config function would still delay the answer, if the usb device got unplugged while waiting for setup_continue to be called. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2bac51a1827a18821150ed8c9f9752c02f9c2b02 upstream.

The delayed_status value is used to keep track of status response
packets on ep0. It needs to be reset or the set_config function would
still delay the answer, if the usb device got unplugged while waiting
for setup_continue to be called.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: dwc3: fix implementation of endpoint wedge 2013-12-20T15:48:54+00:00 Alan Stern stern@rowland.harvard.edu 2013-11-01T16:05:12+00:00 14d9ceaf84edebb520b2b7c1f8800fef5364ccbf commit a535d81c92615b8ffb99b7e1fd1fb01effaed1af upstream. The dwc3 UDC driver doesn't implement endpoint wedging correctly. When an endpoint is wedged, the gadget driver should be allowed to clear the wedge by calling usb_ep_clear_halt(). Only the host is prevented from resetting the endpoint. This patch fixes the implementation. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Pratyush Anand <pratyush.anand@st.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a535d81c92615b8ffb99b7e1fd1fb01effaed1af upstream.

The dwc3 UDC driver doesn't implement endpoint wedging correctly.
When an endpoint is wedged, the gadget driver should be allowed to
clear the wedge by calling usb_ep_clear_halt().  Only the host is
prevented from resetting the endpoint.

This patch fixes the implementation.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: hub: Use correct reset for wedged USB3 devices that are NOTATTACHED 2013-12-20T15:48:54+00:00 Julius Werner jwerner@chromium.org 2013-11-07T18:59:14+00:00 fb4e47f9e933441aa17bb7aa8f505444927ea10b commit 2d51f3cd11f414c56a87dc018196b85fd50b04a4 upstream. This patch adds a check for USB_STATE_NOTATTACHED to the hub_port_warm_reset_required() workaround for ports that end up in Compliance Mode in hub_events() when trying to decide which reset function to use. Trying to call usb_reset_device() with a NOTATTACHED device will just fail and leave the port broken. Signed-off-by: Julius Werner <jwerner@chromium.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2d51f3cd11f414c56a87dc018196b85fd50b04a4 upstream.

This patch adds a check for USB_STATE_NOTATTACHED to the
hub_port_warm_reset_required() workaround for ports that end up in
Compliance Mode in hub_events() when trying to decide which reset
function to use. Trying to call usb_reset_device() with a NOTATTACHED
device will just fail and leave the port broken.

Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: cdc-acm: Added support for the Lenovo RD02-D400 USB Modem 2013-12-12T06:37:56+00:00 David Cluytens david.cluytens@gmail.com 2013-12-03T13:18:57+00:00 90c06d2ba01742f7d0db83476e02d81dfa1d160a commit 3b59d16c513da258ec8f6a0b4db85f257a0380d6 upstream. Signed-off-by: David Cluytens <david.cluytens@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 3b59d16c513da258ec8f6a0b4db85f257a0380d6 upstream.

Signed-off-by: David Cluytens <david.cluytens@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: spcp8x5: correct handling of CS5 setting 2013-12-12T06:37:56+00:00 Colin Leitner colin.leitner@googlemail.com 2013-11-08T21:53:11+00:00 95502f5d08ed7e56ab909c93925f0f5ee506a1a0 commit 711fbdfbf2bc4827214a650afe3f64767a1aba16 upstream. This patch removes an erroneous check of CSIZE, which made it impossible to set CS5. Compiles clean, but couldn't test against hardware. Signed-off-by: Colin Leitner <colin.leitner@gmail.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 711fbdfbf2bc4827214a650afe3f64767a1aba16 upstream.

This patch removes an erroneous check of CSIZE, which made it impossible to set
CS5.

Compiles clean, but couldn't test against hardware.

Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>