linux-stable.git/drivers/usb, branch v3.12.52

usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message

2016-01-05T16:48:52+00:00

commit 5377adb092664d336ac212499961cac5e8728794 upstream.

usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.

Fixes: ff30cbc8da42 ("usb: Use the USB_SS_MULT() macro to get the ...")
Signed-off-by: Ben Hutchings 
Signed-off-by: Jiri Slaby

USB: whci-hcd: add check for dma mapping error

2016-01-05T16:48:51+00:00

commit f9fa1887dcf26bd346665a6ae3d3f53dec54cba1 upstream.

qset_fill_page_list() do not check for dma mapping errors.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov 
Signed-off-by: Jiri Slaby

USB: add quirk for devices with broken LPM

2016-01-05T16:48:51+00:00

commit ad87e03213b552a5c33d5e1e7a19a73768397010 upstream.

Some USB device / host controller combinations seem to have problems
with Link Power Management.  For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.

This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.

Signed-off-by: Alan Stern 
Reported-by: Steinar H. Gunderson 
Signed-off-by: Jiri Slaby

USB: cp210x: Remove CP2110 ID from compatibility list

2016-01-05T16:48:51+00:00

commit 7c90e610b60cd1ed6abafd806acfaedccbbe52d1 upstream.

CP2110 ID (0x10c4, 0xea80) doesn't belong here because it's a HID
and completely different from CP210x devices.

Signed-off-by: Konstantin Shkolnyy 
Signed-off-by: Johan Hovold 
Signed-off-by: Jiri Slaby

USB: serial: Another Infineon flash loader USB ID

2016-01-05T16:48:51+00:00

commit a0e80fbd56b4573de997c9a088a33abbc1121400 upstream.

The flash loader has been seen on a Telit UE910 modem. The flash loader
is a bit special, it presents both an ACM and CDC Data interface but
only the latter is useful. Unless a magic string is sent to the device
it will disappear and the regular modem device appears instead.

Signed-off-by: Jonas Jonsson 
Tested-by: Daniele Palmas 
Signed-off-by: Johan Hovold 
Signed-off-by: Jiri Slaby

USB: cdc_acm: Ignore Infineon Flash Loader utility

2016-01-05T16:48:51+00:00

commit f33a7f72e5fc033daccbb8d4753d7c5c41a4d67b upstream.

Some modems, such as the Telit UE910, are using an Infineon Flash Loader
utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC
Data). The latter can be used as a serial interface to upgrade the
firmware of the modem. However, that isn't possible when the cdc-acm
driver takes control of the device.

The following is an explanation of the behaviour by Daniele Palmas during
discussion on linux-usb.

"This is what happens when the device is turned on (without modifying
the drivers):

[155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci
[155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11
[155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041
[155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device

This is the flashing device that is caught by the cdc-acm driver. Once
the ttyACM appears, the application starts sending a magic string
(simple write on the file descriptor) to keep the device in flashing
mode. If this magic string is not properly received in a certain time
interval, the modem goes on in normal operative mode:

[155493.748094] usb 1-3: USB disconnect, device number 27
[155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci
[155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021
[155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM
[155495.059989] usb 1-3: Manufacturer: Telit
[155495.059992] usb 1-3: SerialNumber: 359658044004697
[155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
[155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device
[155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device
[155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device
[155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device
[155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device
[155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14

Using the cdc-acm driver, the string, though being sent in the same way
than using the usb-serial-simple driver (I can confirm that the data is
passing properly since I used an hw usb sniffer), does not make the
device to stay in flashing mode."

Signed-off-by: Jonas Jonsson 
Tested-by: Daniele Palmas 
Signed-off-by: Johan Hovold 
Signed-off-by: Jiri Slaby

USB: option: add XS Stick W100-2 from 4G Systems

2016-01-05T15:23:36+00:00

commit 638148e20c7f8f6e95017fdc13bce8549a6925e0 upstream.

Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1c9e ProdID=9b01 Rev=02.32
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=
C:  #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Now all important things are there:

wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)

There is also ttyUSB0, but it is not usable, at least not for at.

The device works well with qmi and ModemManager-NetworkManager.
"

Reported-by: Thomas Schäfer 
Signed-off-by: Bjørn Mork 
Signed-off-by: Jiri Slaby

USB: serial: option: add support for Novatel MiFi USB620L

2016-01-05T15:23:36+00:00

commit e07af133c3e2716db25e3e1e1d9f10c2088e9c1a upstream.

Also known as Verizon U620L.

The device is modeswitched from 1410:9020 to 1410:9022 by selecting the
4th USB configuration:

 $ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4

This configuration provides a ECM interface as well as TTYs ('Enterprise
Mode' according to the U620 Linux integration guide).

Signed-off-by: Aleksander Morgado 
Signed-off-by: Johan Hovold 
Signed-off-by: Jiri Slaby

USB: ti_usb_3410_5052: Add Honeywell HGI80 ID

2016-01-05T15:23:36+00:00

commit 1bcb49e663f88bccee35b8688e6a3da2bea31fd4 upstream.

The Honeywell HGI80 is a wireless interface to the evohome connected
thermostat. It uses a TI 3410 USB-serial port.

Signed-off-by: David Woodhouse 
Signed-off-by: Johan Hovold 
Signed-off-by: Jiri Slaby

usb: musb: core: fix order of arguments to ulpi write callback

2016-01-05T15:23:36+00:00

commit 705e63d2b29c8bbf091119084544d353bda70393 upstream.

There is a bit of a mess in the order of arguments to the ulpi write
callback. There is

	int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)

in drivers/usb/common/ulpi.c;

	struct usb_phy_io_ops {
		...
		int (*write)(struct usb_phy *x, u32 val, u32 reg);
	}

in include/linux/usb/phy.h.

The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.

Fixes: ffb865b1e460 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König 
Signed-off-by: Felipe Balbi 
Signed-off-by: Jiri Slaby