linux-stable.git/drivers/usb, branch v3.10.71

usb: core: buffer: smallest buffer should start at ARCH_DMA_MINALIGN

2015-03-06T22:40:51+00:00

commit 5efd2ea8c9f4f12916ffc8ba636792ce052f6911 upstream.

the following error pops up during "testusb -a -t 10"
| musb-hdrc musb-hdrc.1.auto: dma_pool_free buffer-128,	f134e000/be842000 (bad dma)
hcd_buffer_create() creates a few buffers, the smallest has 32 bytes of
size. ARCH_KMALLOC_MINALIGN is set to 64 bytes. This combo results in
hcd_buffer_alloc() returning memory which is 32 bytes aligned and it
might by identified by buffer_offset() as another buffer. This means the
buffer which is on a 32 byte boundary will not get freed, instead it
tries to free another buffer with the error message.

This patch fixes the issue by creating the smallest DMA buffer with the
size of ARCH_KMALLOC_MINALIGN (or 32 in case ARCH_KMALLOC_MINALIGN is
smaller). This might be 32, 64 or even 128 bytes. The next three pools
will have the size 128, 512 and 2048.
In case the smallest pool is 128 bytes then we have only three pools
instead of four (and zero the first entry in the array).
The last pool size is always 2048 bytes which is the assumed PAGE_SIZE /
2 of 4096. I doubt it makes sense to continue using PAGE_SIZE / 2 where
we would end up with 8KiB buffer in case we have 16KiB pages.
Instead I think it makes sense to have a common size(s) and extend them
if there is need to.
There is a BUILD_BUG_ON() now in case someone has a minalign of more than
128 bytes.

Signed-off-by: Sebastian Andrzej Siewior 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: fix use-after-free bug in usb_hcd_unlink_urb()

2015-03-06T22:40:51+00:00

commit c99197902da284b4b723451c1471c45b18537cde upstream.

The usb_hcd_unlink_urb() routine in hcd.c contains two possible
use-after-free errors.  The dev_dbg() statement at the end of the
routine dereferences urb and urb->dev even though both structures may
have been deallocated.

This patch fixes the problem by storing urb->dev in a local variable
(avoiding the dereference of urb) and moving the dev_dbg() up before
the usb_put_dev() call.

Signed-off-by: Alan Stern 
Reported-by: Joe Lawrence 
Tested-by: Joe Lawrence 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

USB: cp210x: add ID for RUGGEDCOM USB Serial Console

2015-03-06T22:40:51+00:00

commit a6f0331236fa75afba14bbcf6668d42cebb55c43 upstream.

Added the USB serial console device ID for Siemens Ruggedcom devices
which have a USB port for their serial console.

Signed-off-by: Len Sorensen 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: keyspan: fix null-deref at probe

2015-01-27T15:52:32+00:00

commit b5122236bba8d7ef62153da5b55cc65d0944c61e upstream.

Fix null-pointer dereference during probe if the interface-status
completion handler is called before the individual ports have been set
up.

Fixes: f79b2d0fe81e ("USB: keyspan: fix NULL-pointer dereferences and
memory leaks")
Reported-by: Richard 
Tested-by: Richard 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: cp210x: add IDs for CEL USB sticks and MeshWorks devices

2015-01-27T15:52:32+00:00

commit 1ae78a4870989a354028cb17dabf819b595e70e3 upstream.

Added virtual com port VID/PID entries for CEL USB sticks and MeshWorks
devices.

Signed-off-by: David Peterson 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: cp210x: fix ID for production CEL MeshConnect USB Stick

2015-01-27T15:52:32+00:00

commit 90441b4dbe90ba0c38111ea89fa093a8c9627801 upstream.

Fixing typo for MeshConnect IDs. The original PID (0x8875) is not in
production and is not needed. Instead it has been changed to the
official production PID (0x8857).

Signed-off-by: Preston Fick 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

usb: dwc3: gadget: Stop TRB preparation after limit is reached

2015-01-27T15:52:32+00:00

commit 39e60635a01520e8c8ed3946a28c2b98e6a46f79 upstream.

DWC3 gadget sets up a pool of 32 TRBs for each EP during initialization. This
means, the max TRBs that can be submitted for an EP is fixed to 32. Since the
request queue for an EP is a linked list, any number of requests can be queued
to it by the gadget layer.  However, the dwc3 driver must not submit TRBs more
than the pool it has created for. This limit wasn't respected when SG was used
resulting in submitting more than the max TRBs, eventually leading to
non-transfer of the TRBs submitted over the max limit.

Root cause:
When SG is used, there are two loops iterating to prepare TRBs:
 - Outer loop over the request_list
 - Inner loop over the SG list
The code was missing break to get out of the outer loop.

Fixes: eeb720fb21d6 (usb: dwc3: gadget: add support for SG lists)
Signed-off-by: Amit Virdi 
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

usb: dwc3: gadget: Fix TRB preparation during SG

2015-01-27T15:52:32+00:00

commit ec512fb8e5611fed1df2895f90317ce6797d6b32 upstream.

When scatter gather (SG) is used, multiple TRBs are prepared from one DWC3
request (dwc3_request). So while preparing TRBs, the 'last' flag should be set
only when it is the last TRB being prepared from the last dwc3_request entry.

The current implementation uses list_is_last to check if the dwc3_request is the
last entry from the request_list. However, list_is_last returns false for the
last entry too. This is because, while preparing the first TRB from a request,
the function dwc3_prepare_one_trb modifies the request's next and prev pointers
while moving the URB to req_queued. Hence, list_is_last always returns false no
matter what.

The correct way is not to access the modified pointers of dwc3_request but to
use list_empty macro instead.

Fixes: e5ba5ec833aa (usb: dwc3: gadget: fix scatter gather implementation)
Signed-off-by: Amit Virdi 
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

OHCI: add a quirk for ULi M5237 blocking on reset

2015-01-27T15:52:32+00:00

commit 56abcab833fafcfaeb2f5b25e0364c1dec45f53e upstream.

Commit 8dccddbc2368 ("OHCI: final fix for NVIDIA problems (I hope)")
introduced into 3.1.9 broke boot on e.g. Freescale P2020DS development
board. The code path that was previously specific to NVIDIA controllers
had then become taken for all chips.

However, the M5237 installed on the board wedges solid when accessing
its base+OHCI_FMINTERVAL register, making it impossible to boot any
kernel newer than 3.1.8 on this particular and apparently other similar
machines.

Don't readl() and writel() base+OHCI_FMINTERVAL on PCI ID 10b9:5237.

The patch is suitable for the -next tree as well as all maintained
kernels up to 3.2 inclusive.

Signed-off-by: Arseny Solokha 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

cdc-acm: memory leak in error case

2015-01-16T14:59:02+00:00

commit d908f8478a8d18e66c80a12adb27764920c1f1ca upstream.

If probe() fails not only the attributes need to be removed
but also the memory freed.

Reported-by: Ahmed Tamrawi 
Signed-off-by: Oliver Neukum 
Signed-off-by: Greg Kroah-Hartman