linux-stable.git/drivers/usb, branch v3.10.58

USB: cp210x: add support for Seluxit USB dongle

2014-10-15T06:31:58+00:00

commit dee80ad12d2b1b304286a707fde7ab05d1fc7bab upstream.

Added the Seluxit ApS USB Serial Dongle to cp210x driver.

Signed-off-by: Andreas Bomholtz 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: serial: cp210x: added Ketra N1 wireless interface support

2014-10-15T06:31:57+00:00

commit bfc2d7dfdd761ae3beccdb26abebe03cef042f46 upstream.

Added support for Ketra N1 wireless interface, which uses the
Silicon Labs' CP2104 USB to UART bridge with customized PID 8946.

Signed-off-by: Joe Savage 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: Add device quirk for ASUS T100 Base Station keyboard

2014-10-15T06:31:57+00:00

commit ddbe1fca0bcb87ca8c199ea873a456ca8a948567 upstream.

This full-speed USB device generates spurious remote wakeup event
as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result,
Linux can't enter system suspend and S0ix power saving modes once
this keyboard is used.

This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk.
With this quirk set, wakeup capability will be ignored during
device configure.

This patch could be back-ported to kernels as old as 2.6.39.

Signed-off-by: Lu Baolu 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

usb: dwc3: core: fix ordering for PHY suspend

2014-10-05T21:54:13+00:00

commit dc99f16f076559235c92d3eb66d03d1310faea08 upstream.

We can't suspend the PHYs before dwc3_core_exit_mode()
has been called, that's because the host and/or device
sides might still need to communicate with the far end
link partner.

Fixes: 8ba007a (usb: dwc3: core: enable the USB2 and USB3 phy in probe)
Suggested-by: Alan Stern 
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

usb: dwc3: core: fix order of PM runtime calls

2014-10-05T21:54:13+00:00

commit fed33afce0eda44a46ae24d93aec1b5198c0bac4 upstream.

Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.

Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.

Fixes: 72246da (usb: Introduce DesignWare USB3 DRD Driver)
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

usb: host: xhci: fix compliance mode workaround

2014-10-05T21:54:13+00:00

commit 96908589a8b2584b1185f834d365f5cc360e8226 upstream.

Commit 71c731a (usb: host: xhci: Fix Compliance Mode
on SN65LVP3502CP Hardware) implemented a workaround
for a known issue with Texas Instruments' USB 3.0
redriver IC but it left a condition where any xHCI
host would be taken out of reset if port was placed
in compliance mode and there was no device connected
to the port.

That condition would trigger a fake connection to a
non-existent device so that usbcore would trigger a
warm reset of the port, thus taking the link out of
reset.

This has the side-effect of preventing any xHCI host
connected to a Linux machine from starting and running
the USB 3.0 Electrical Compliance Suite because the
port will mysteriously taken out of compliance mode
and, thus, xHCI won't step through the necessary
compliance patterns for link validation.

This patch fixes the issue by just adding a missing
check for XHCI_COMP_MODE_QUIRK inside
xhci_hub_report_usb3_link_state() when PORT_CAS isn't
set.

This patch should be backported to all kernels containing
commit 71c731a.

Fixes: 71c731a (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware)
Cc: Alexis R. Cortes 
Cc:  # v3.2+
Signed-off-by: Felipe Balbi 
Acked-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb:hub set hub->change_bits when over-current happens

2014-10-05T21:54:10+00:00

commit 08d1dec6f4054e3613f32051d9b149d4203ce0d2 upstream.

When we are doing compliance test with xHCI, we found that if we
enable CONFIG_USB_SUSPEND and plug in a bad device which causes
over-current condition to the root port, software will not be noticed.
The reason is that current code don't set hub->change_bits in
hub_activate() when over-current happens, and then hub_events() will
not check the port status because it thinks nothing changed.
If CONFIG_USB_SUSPEND is disabled, the interrupt pipe of the hub will
report the change and set hub->event_bits, and then hub_events() will
check what events happened.In this case over-current can be detected.

Signed-off-by: Shen Guang 
Acked-by: Alan Stern 
Acked-by: Sarah Sharp 
Cc: Frans Klaver 
Signed-off-by: Greg Kroah-Hartman

usb: dwc3: omap: fix ordering for runtime pm calls

2014-10-05T21:54:10+00:00

commit 81a60b7f5c143ab3cdcd9943c9b4b7c63c32fc31 upstream.

we don't to gate clocks until our children are
done with their remove path.

Fixes: af310e9 (usb: dwc3: omap: use runtime API's to enable clocks)
Signed-off-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

USB: EHCI: unlink QHs even after the controller has stopped

2014-10-05T21:54:10+00:00

commit 7312b5ddd47fee2356baa78c5516ef8e04eed452 upstream.

Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH.  This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.

But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed.  Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.

Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.

Signed-off-by: Alan Stern 
Reported-by: Joe Lawrence 
Tested-by: Joe Lawrence 
Signed-off-by: Greg Kroah-Hartman

USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters

2014-10-05T21:54:10+00:00

commit c80b4495c61636edc58fe1ce300f09f24db28e10 upstream.

This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.

The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.

Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.

My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.

This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?

Signed-off-by: Mark Knibbs 
Signed-off-by: Greg Kroah-Hartman