linux-stable.git/drivers/usb, branch v3.0.45 Linux kernel stable tree Increase XHCI suspend timeout to 16ms 2012-10-07T15:27:26+00:00 Michael Spang spang@chromium.org 2012-09-14T17:05:49+00:00 a4e92d29a86daf9609c875eccb1357657f2ac93f commit a6e097dfdfd189b6929af6efa1d289af61858386 upstream. The Intel XHCI specification says that after clearing the run/stop bit the controller may take up to 16ms to halt. We've seen a device take 14ms, which with the current timeout of 10ms causes the kernel to abort the suspend. Increasing the timeout to the recommended value fixes the problem. This patch should be backported to kernels as old as 2.6.37, that contain the commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI: PCI power management implementation". Signed-off-by: Michael Spang <spang@chromium.org> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a6e097dfdfd189b6929af6efa1d289af61858386 upstream.

The Intel XHCI specification says that after clearing the run/stop bit
the controller may take up to 16ms to halt. We've seen a device take
14ms, which with the current timeout of 10ms causes the kernel to
abort the suspend. Increasing the timeout to the recommended value
fixes the problem.

This patch should be backported to kernels as old as 2.6.37, that
contain the commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI:
PCI power management implementation".

Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Intel Panther Point BEI quirk. 2012-10-07T15:27:25+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-09-19T23:27:26+00:00 9c1ce83c1250a3ad4c2d131d59295561b09efe83 commit 80fab3b244a22e0ca539d2439bdda50e81e5666f upstream. When a device with an isochronous endpoint is behind a hub plugged into the Intel Panther Point xHCI host controller, and the driver submits multiple frames per URB, the xHCI driver will set the Block Event Interrupt (BEI) flag on all but the last TD for the URB. This causes the host controller to place an event on the event ring, but not send an interrupt. When the last TD for the URB completes, BEI is cleared, and we get an interrupt for the whole URB. However, under a Panther Point xHCI host controller, if the parent hub is unplugged when one or more events from transfers with BEI set are on the event ring, a port status change event is placed on the event ring, but no interrupt is generated. This means URBs stop completing, and the USB device disconnect is not noticed. Something like a USB headset will cause mplayer to hang when the device is disconnected. If another transfer is sent (such as running `sudo lsusb -v`), the next transfer event seems to "unstick" the event ring, the xHCI driver gets an interrupt, and the disconnect is reported to the USB core. The fix is not to use the BEI flag under the Panther Point xHCI host. This will impact power consumption and system responsiveness, because the xHCI driver will receive an interrupt for every frame in all isochronous URBs instead of once per URB. Intel chipset developers confirm that this bug will be hit if the BEI flag is used on any endpoint, not just ones that are behind a hub. This patch should be backported to kernels as old as 3.0, that contain the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 80fab3b244a22e0ca539d2439bdda50e81e5666f upstream.

When a device with an isochronous endpoint is behind a hub plugged into
the Intel Panther Point xHCI host controller, and the driver submits
multiple frames per URB, the xHCI driver will set the Block Event
Interrupt (BEI) flag on all but the last TD for the URB.  This causes
the host controller to place an event on the event ring, but not send an
interrupt.  When the last TD for the URB completes, BEI is cleared, and
we get an interrupt for the whole URB.

However, under a Panther Point xHCI host controller, if the parent hub
is unplugged when one or more events from transfers with BEI set are on
the event ring, a port status change event is placed on the event ring,
but no interrupt is generated.  This means URBs stop completing, and the
USB device disconnect is not noticed.  Something like a USB headset will
cause mplayer to hang when the device is disconnected.

If another transfer is sent (such as running `sudo lsusb -v`), the next
transfer event seems to "unstick" the event ring, the xHCI driver gets
an interrupt, and the disconnect is reported to the USB core.

The fix is not to use the BEI flag under the Panther Point xHCI host.
This will impact power consumption and system responsiveness, because
the xHCI driver will receive an interrupt for every frame in all
isochronous URBs instead of once per URB.

Intel chipset developers confirm that this bug will be hit if the BEI
flag is used on any endpoint, not just ones that are behind a hub.

This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: qcaux: add Pantech vendor class match 2012-10-07T15:27:24+00:00 Bjørn Mork bjorn@mork.no 2012-09-19T20:02:03+00:00 bd6a0fa2282e6cc0c951bda5e1e0e97291987e10 commit c638eb2872b3af079501e7ee44cbb8a5cce9b4b5 upstream. The three Pantech devices UML190 (106c:3716), UML290 (106c:3718) and P4200 (106c:3721) all use the same subclasses to identify vendor specific functions. Replace the existing device specific entries with generic vendor matching, adding support for the P4200. Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: Thomas Schäfer <tschaefer@t-online.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c638eb2872b3af079501e7ee44cbb8a5cce9b4b5 upstream.

The three Pantech devices UML190 (106c:3716), UML290 (106c:3718) and
P4200 (106c:3721) all use the same subclasses to identify vendor
specific functions.  Replace the existing device specific entries
with generic vendor matching, adding support for the P4200.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: ftdi_sio: add TIAO USB Multi-Protocol Adapter (TUMPA) support 2012-10-07T15:27:24+00:00 Antonio Ospite ospite@studenti.unina.it 2012-09-23T07:57:25+00:00 3f72cbca902c6059a296f1df79b42020e75dbe4c commit 54575b05af36959dfb6a49a3e9ca0c2b456b7126 upstream. TIAO/DIYGADGET USB Multi-Protocol Adapter (TUMPA) is an FTDI FT2232H based device which provides an easily accessible JTAG, SPI, I2C, serial breakout. http://www.diygadget.com/tiao-usb-multi-protocol-adapter-jtag-spi-i2c-serial.html http://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User%27s_Manual FTDI FT2232H provides two serial channels (A and B), but on the TUMPA channel A is dedicated to JTAG/SPI while channel B can be used for UART/RS-232: use the ftdi_jtag_quirk to expose only channel B as a usb-serial interface to userspace. Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 54575b05af36959dfb6a49a3e9ca0c2b456b7126 upstream.

TIAO/DIYGADGET USB Multi-Protocol Adapter (TUMPA) is an FTDI FT2232H
based device which provides an easily accessible JTAG, SPI, I2C, serial
breakout.

http://www.diygadget.com/tiao-usb-multi-protocol-adapter-jtag-spi-i2c-serial.html
http://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User%27s_Manual

FTDI FT2232H provides two serial channels (A and B), but on the TUMPA
channel A is dedicated to JTAG/SPI while channel B can be used for
UART/RS-232: use the ftdi_jtag_quirk to expose only channel B as
a usb-serial interface to userspace.

Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: option: blacklist QMI interface on ZTE MF683 2012-10-07T15:27:23+00:00 Bjørn Mork bjorn@mork.no 2012-09-19T20:02:12+00:00 952c5d808a20104a77d15ae857fd221182e27c10 commit 160c9425ac52cb30502be2d9c5e848cec91bb115 upstream. Interface #5 on ZTE MF683 is a QMI/wwan interface. Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: Shawn J. Goff <shawn7400@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 160c9425ac52cb30502be2d9c5e848cec91bb115 upstream.

Interface #5 on ZTE MF683 is a QMI/wwan interface.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: Shawn J. Goff <shawn7400@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: Fix race condition when removing host controllers 2012-10-02T16:47:55+00:00 Alan Stern stern@rowland.harvard.edu 2012-09-26T17:09:53+00:00 b15ab4ac6ae748d3552b0cb112dff5c9c567d4ca commit 0d00dc2611abbe6ad244d50569c2ee82ce42846c upstream. This patch (as1607) fixes a race that can occur if a USB host controller is removed while a process is reading the /sys/kernel/debug/usb/devices file. The usb_device_read() routine uses the bus->root_hub pointer to determine whether or not the root hub is registered. The is not a valid test, because the pointer is set before the root hub gets registered and remains set even after the root hub is unregistered and deallocated. As a result, usb_device_read() or usb_device_dump() can access freed memory, causing an oops. The patch changes the test to use the hcd->rh_registered flag, which does get set and cleared at the appropriate times. It also makes sure to hold the usb_bus_list_lock mutex while setting the flag, so that usb_device_read() will become aware of new root hubs as soon as they are registered. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Don Zickus <dzickus@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 0d00dc2611abbe6ad244d50569c2ee82ce42846c upstream.

This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.

The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered.  The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated.  As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.

The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times.  It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Fix bug after deq ptr set to link TRB. 2012-10-02T16:47:39+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-07-26T19:03:59+00:00 e3439be1c0b9df0ca9b760ff4861be5d6145da26 commit 50d0206fcaea3e736f912fd5b00ec6233fb4ce44 upstream. This patch fixes a particularly nasty bug that was revealed by the ring expansion patches. The bug has been present since the very beginning of the xHCI driver history, and could have caused general protection faults from bad memory accesses. The first thing to note is that a Set TR Dequeue Pointer command can move the dequeue pointer to a link TRB, if the canceled or stalled transfer TD ended just before a link TRB. The function to increment the dequeue pointer, inc_deq, was written before cancellation and stall support was added. It assumed that the dequeue pointer could never point to a link TRB. It would unconditionally increment the dequeue pointer at the start of the function, check if the pointer was now on a link TRB, and move it to the top of the next segment if so. This means that if a Set TR Dequeue Point command moved the dequeue pointer to a link TRB, a subsequent call to inc_deq() would move the pointer off the segment and into la-la-land. It would then read from that memory to determine if it was a link TRB. Other functions would often call inc_deq() until the dequeue pointer matched some other pointer, which means this function would quite happily read all of system memory before wrapping around to the right pointer value. Often, there would be another endpoint segment from a different ring allocated from the same DMA pool, which would be contiguous to the segment inc_deq just stepped off of. inc_deq would eventually find the link TRB in that segment, and blindly move the dequeue pointer back to the top of the correct ring segment. The only reason the original code worked at all is because there was only one ring segment. With the ring expansion patches, the dequeue pointer would eventually wrap into place, but the dequeue segment would be out-of-sync. On the second TD after the dequeue pointer was moved to a link TRB, trb_in_td() would fail (because the dequeue pointer and dequeue segment were out-of-sync), and this message would appear: ERROR Transfer event TRB DMA ptr not part of current TD This fixes bugzilla entry 4333 (option-based modem unhappy on USB 3.0 port: "Transfer event TRB DMA ptr not part of current TD", "rejecting I/O to offline device"), https://bugzilla.kernel.org/show_bug.cgi?id=43333 and possibly other general protection fault bugs as well. This patch should be backported to kernels as old as 2.6.31. A separate patch will be created for kernels older than 3.4, since inc_deq was modified in 3.4 and this patch will not apply. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: James Ettle <theholyettlz@googlemail.com> Tested-by: Matthew Hall <mhall@mhcomputing.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 50d0206fcaea3e736f912fd5b00ec6233fb4ce44 upstream.

This patch fixes a particularly nasty bug that was revealed by the ring
expansion patches.  The bug has been present since the very beginning of
the xHCI driver history, and could have caused general protection faults
from bad memory accesses.

The first thing to note is that a Set TR Dequeue Pointer command can
move the dequeue pointer to a link TRB, if the canceled or stalled
transfer TD ended just before a link TRB.  The function to increment the
dequeue pointer, inc_deq, was written before cancellation and stall
support was added.  It assumed that the dequeue pointer could never
point to a link TRB.  It would unconditionally increment the dequeue
pointer at the start of the function, check if the pointer was now on a
link TRB, and move it to the top of the next segment if so.

This means that if a Set TR Dequeue Point command moved the dequeue
pointer to a link TRB, a subsequent call to inc_deq() would move the
pointer off the segment and into la-la-land.  It would then read from
that memory to determine if it was a link TRB.  Other functions would
often call inc_deq() until the dequeue pointer matched some other
pointer, which means this function would quite happily read all of
system memory before wrapping around to the right pointer value.

Often, there would be another endpoint segment from a different ring
allocated from the same DMA pool, which would be contiguous to the
segment inc_deq just stepped off of.  inc_deq would eventually find the
link TRB in that segment, and blindly move the dequeue pointer back to
the top of the correct ring segment.

The only reason the original code worked at all is because there was
only one ring segment.  With the ring expansion patches, the dequeue
pointer would eventually wrap into place, but the dequeue segment would
be out-of-sync.  On the second TD after the dequeue pointer was moved to
a link TRB, trb_in_td() would fail (because the dequeue pointer and
dequeue segment were out-of-sync), and this message would appear:

ERROR Transfer event TRB DMA ptr not part of current TD

This fixes bugzilla entry 4333 (option-based modem unhappy on USB 3.0
port: "Transfer event TRB DMA ptr not part of current TD", "rejecting
I/O to offline device"),

	https://bugzilla.kernel.org/show_bug.cgi?id=43333

and possibly other general protection fault bugs as well.

This patch should be backported to kernels as old as 2.6.31.  A separate
patch will be created for kernels older than 3.4, since inc_deq was
modified in 3.4 and this patch will not apply.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: James Ettle <theholyettlz@googlemail.com>
Tested-by: Matthew Hall <mhall@mhcomputing.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: host: xhci: fix compilation error for non-PCI based stacks 2012-10-02T16:47:39+00:00 Moiz Sonasath m-sonasath@ti.com 2012-09-05T05:34:26+00:00 d8ec66c5a565c5ca47d2740226f3e2035c1883bf commit 296365781903226a3fb8758901eaeec09d2798e4 upstream. For non PCI-based stacks, this function call usb_disable_xhci_ports(to_pci_dev(hcd->self.controller)); made from xhci_shutdown is not applicable. Ideally, we wouldn't have any PCI-specific code on a generic driver such as the xHCI stack, but it looks like we should just stub usb_disable_xhci_ports() out for non-PCI devices. [ balbi@ti.com: slight improvement to commit log ] This patch should be backported to kernels as old as 3.0, since the commit it fixes (e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch PPT ports to EHCI on shutdown.") was marked for stable. Signed-off-by: Moiz Sonasath<m-sonasath@ti.com> Signed-off-by: Ruchika Kharwar <ruchika@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 296365781903226a3fb8758901eaeec09d2798e4 upstream.

For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.

Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.

[ balbi@ti.com: slight improvement to commit log ]

This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.

Signed-off-by: Moiz Sonasath<m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Recognize USB 3.0 devices as superspeed at powerup 2012-10-02T16:47:39+00:00 Manoj Iyer manoj.iyer@canonical.com 2012-08-22T16:53:18+00:00 b1e81baa2d46338345c6f16c0e873ef3e7d73188 commit 29d214576f936db627ff62afb9ef438eea18bcd2 upstream. On Intel Panther Point chipset USB 3.0 devices show up as high-speed devices on powerup, but after an s3 cycle they are correctly recognized as SuperSpeed. At powerup switch the port to xHCI so that USB 3.0 devices are correctly recognized. BugLink: http://bugs.launchpad.net/bugs/1000424 This patch should be backported to kernels as old as 3.0, that contain commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 29d214576f936db627ff62afb9ef438eea18bcd2 upstream.

On Intel Panther Point chipset USB 3.0 devices show up as
high-speed devices on powerup, but after an s3 cycle they are
correctly recognized as SuperSpeed. At powerup switch the port
to xHCI so that USB 3.0 devices are correctly recognized.

BugLink: http://bugs.launchpad.net/bugs/1000424

This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."

Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Make handover code more robust 2012-10-02T16:47:39+00:00 Matthew Garrett mjg@redhat.com 2012-08-14T20:44:49+00:00 f78e6ad433084ec0b7bc40ff9910f458609ee9cb commit e955a1cd086de4d165ae0f4c7be7289d84b63bdc upstream. My test platform (Intel DX79SI) boots reliably under BIOS, but frequently crashes when booting via UEFI. I finally tracked this down to the xhci handoff code. It seems that reads from the device occasionally just return 0xff, resulting in xhci_find_next_cap_offset generating a value that's larger than the resource region. We then oops when attempting to read the value. Sanity checking that value lets us avoid the crash. I've no idea what's causing the underlying problem, and xhci still doesn't actually *work* even with this, but the machine at least boots which will probably make further debugging easier. This should be backported to kernels as old as 2.6.31, that contain the commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci: BIOS handoff and HW initialization." Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit e955a1cd086de4d165ae0f4c7be7289d84b63bdc upstream.

My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.

I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.

This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci: BIOS handoff
and HW initialization."

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>