linux-stable.git/drivers/usb, branch v3.0.37

xhci: Avoid dead ports when CONFIG_USB_XHCI_HCD=n

2012-07-16T15:47:50+00:00

Commit 51c9e6c7732b67769c0a514d31f505e49fa82dd4 upstream, but modified
to get this to apply on 3.0.

If the user chooses to say "no" to CONFIG_USB_XHCI_HCD on a system
with an Intel Panther Point chipset, the PCI quirks code or the EHCI
driver will switch the ports over to the xHCI host, but the xHCI driver
will never load.  The ports will be powered off and seem "dead" to the
user.

Fix this by only switching the ports over if CONFIG_USB_XHCI_HCD is
either compiled in, or compiled as a module.

This patch should be backported to the 3.0 stable kernel, since it
contains the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel
xhci: Support EHCI/xHCI port switching."

Signed-off-by: Sarah Sharp 
Reported-by: Eric Anholt 
Reported-by: David Bein 
Signed-off-by: Greg Kroah-Hartman

USB: option: Add MEDIATEK product ids

2012-07-16T15:47:50+00:00

commit aacef9c561a693341566a6850c451ce3df68cb9a upstream.

Signed-off-by: Gaosen Zhang 
Signed-off-by: Greg Kroah-Hartman

USB: option: add ZTE MF60

2012-07-16T15:47:50+00:00

commit 8e16e33c168a6efd0c9f7fa9dd4c1e1db9a74553 upstream.

Switches into a composite device by ejecting the initial
driver CD.  The four interfaces are: QCDM, AT, QMI/wwan
and mass storage.  Let this driver manage the two serial
interfaces:

T:  Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 28 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=1402 Rev= 0.00
S:  Manufacturer=ZTE,Incorporated
S:  Product=ZTE WCDMA Technologies MSM
S:  SerialNumber=xxxxx
C:* #Ifs= 4 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=83(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Bjørn Mork 
Signed-off-by: Greg Kroah-Hartman

USB: cdc-wdm: fix lockup on error in wdm_read

2012-07-16T15:47:50+00:00

commit b086b6b10d9f182cd8d2f0dcfd7fd11edba93fc9 upstream.

Clear the WDM_READ flag on empty reads to avoid running
forever in an infinite tight loop, causing lockups:

Jul  1 21:58:11 nemi kernel: [ 3658.898647] qmi_wwan 2-1:1.2: Unexpected error -71
Jul  1 21:58:36 nemi kernel: [ 3684.072021] BUG: soft lockup - CPU#0 stuck for 23s! [qmi.pl:12235]
Jul  1 21:58:36 nemi kernel: [ 3684.072212] CPU 0
Jul  1 21:58:36 nemi kernel: [ 3684.072355]
Jul  1 21:58:36 nemi kernel: [ 3684.072367] Pid: 12235, comm: qmi.pl Tainted: P           O 3.5.0-rc2+ #13 LENOVO 2776LEG/2776LEG
Jul  1 21:58:36 nemi kernel: [ 3684.072383] RIP: 0010:[]  [] spin_unlock_irq+0x8/0xc [cdc_wdm]
Jul  1 21:58:36 nemi kernel: [ 3684.072388] RSP: 0018:ffff88022dca1e70  EFLAGS: 00000282
Jul  1 21:58:36 nemi kernel: [ 3684.072393] RAX: ffff88022fc3f650 RBX: ffffffff811c56f7 RCX: 00000001000ce8c1
Jul  1 21:58:36 nemi kernel: [ 3684.072398] RDX: 0000000000000010 RSI: 000000000267d810 RDI: ffff88022fc3f650
Jul  1 21:58:36 nemi kernel: [ 3684.072403] RBP: ffff88022dca1eb0 R08: ffffffffa063578e R09: 0000000000000000
Jul  1 21:58:36 nemi kernel: [ 3684.072407] R10: 0000000000000008 R11: 0000000000000246 R12: 0000000000000002
Jul  1 21:58:36 nemi kernel: [ 3684.072412] R13: 0000000000000246 R14: ffffffff00000002 R15: ffff8802281d8c88
Jul  1 21:58:36 nemi kernel: [ 3684.072418] FS:  00007f666a260700(0000) GS:ffff88023bc00000(0000) knlGS:0000000000000000
Jul  1 21:58:36 nemi kernel: [ 3684.072423] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Jul  1 21:58:36 nemi kernel: [ 3684.072428] CR2: 000000000270d9d8 CR3: 000000022e865000 CR4: 00000000000007f0
Jul  1 21:58:36 nemi kernel: [ 3684.072433] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
Jul  1 21:58:36 nemi kernel: [ 3684.072438] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Jul  1 21:58:36 nemi kernel: [ 3684.072444] Process qmi.pl (pid: 12235, threadinfo ffff88022dca0000, task ffff88022ff76380)
Jul  1 21:58:36 nemi kernel: [ 3684.072448] Stack:
Jul  1 21:58:36 nemi kernel: [ 3684.072458]  ffffffffa063592e 0000000100020000 ffff88022fc3f650 ffff88022fc3f6a8
Jul  1 21:58:36 nemi kernel: [ 3684.072466]  0000000000000200 0000000100000000 000000000267d810 0000000000000000
Jul  1 21:58:36 nemi kernel: [ 3684.072475]  0000000000000000 ffff880212cfb6d0 0000000000000200 ffff880212cfb6c0
Jul  1 21:58:36 nemi kernel: [ 3684.072479] Call Trace:
Jul  1 21:58:36 nemi kernel: [ 3684.072489]  [] ? wdm_read+0x1a0/0x263 [cdc_wdm]
Jul  1 21:58:36 nemi kernel: [ 3684.072500]  [] ? vfs_read+0xa1/0xfb
Jul  1 21:58:36 nemi kernel: [ 3684.072509]  [] ? alarm_setitimer+0x35/0x64
Jul  1 21:58:36 nemi kernel: [ 3684.072517]  [] ? sys_read+0x45/0x6e
Jul  1 21:58:36 nemi kernel: [ 3684.072525]  [] ? system_call_fastpath+0x16/0x1b
Jul  1 21:58:36 nemi kernel: [ 3684.072557] Code: <66> 66 90 c3 83 ff ed 89 f8 74 16 7f 06 83 ff a1 75 0a c3 83 ff f4

The WDM_READ flag is normally cleared by wdm_int_callback
before resubmitting the read urb, and set by wdm_in_callback
when this urb returns with data or an error.  But a crashing
device may cause both a read error and cancelling all urbs.
Make sure that the flag is cleared by wdm_read if the buffer
is empty.

We don't clear the flag on errors, as there may be pending
data in the buffer which should be processed.  The flag will
instead be cleared on the next wdm_read call.

Signed-off-by: Bjørn Mork 
Acked-by: Oliver Neukum 
Signed-off-by: Greg Kroah-Hartman

USB: CP210x Add 10 Device IDs

2012-07-16T15:47:48+00:00

commit 3fcc8f96829776cf181918461923d1e3bbb831a2 upstream.

This patch adds 10 device IDs for CP210x based devices from the following manufacturers:
Timewave
Clipsal
Festo
Link Instruments

Signed-off-by: Craig Shelley 
Signed-off-by: Greg Kroah-Hartman

USB: option: Add USB ID for Novatel Ovation MC551

2012-07-16T15:47:48+00:00

commit 065b07e7a14676f4138ce4619d229c0be5a74230 upstream.

This device is also known as the Verizon USB551L.

Signed-off-by: Forest Bond 
Acked-by: Dan Williams 
Signed-off-by: Greg Kroah-Hartman

USB: option: add id for Cellient MEN-200

2012-07-16T15:47:48+00:00

commit 1e2c4e59d2b8797973471b4a287a43eac12a0f40 upstream.

Add vendor and product ID to option.c driver
for Cellient MEN-200 EVDO Rev.B 450MHz data module.
http://cellient.com

Signed-off-by: Dmitry Shmygov 
Signed-off-by: Greg Kroah-Hartman

USB: fix gathering of interface associations

2012-06-22T18:34:16+00:00

commit b3a3dd074f7053ef824ad077e5331b52220ceba1 upstream.

TEAC's UD-H01 (and probably other devices) have a gap in the interface
number allocation of their descriptors:

  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength          220
    bNumInterfaces          3
    [...]
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      [...]
    Interface Association:
      bLength                 8
      bDescriptorType        11
      bFirstInterface         2
      bInterfaceCount         2
      bFunctionClass          1 Audio
      bFunctionSubClass       0
      bFunctionProtocol      32
      iFunction               4
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      [...]

Once a configuration is selected, usb_set_configuration() walks the
known interfaces of a given configuration and calls find_iad() on
each of them to set the interface association pointer the interface
is included in.

The problem here is that the loop variable is taken for the interface
number in the comparison logic that gathers the association. Which is
fine as long as the descriptors are sane.

In the case above, however, the logic gets out of sync and the
interface association fields of all interfaces beyond the interface
number gap are wrong.

Fix this by passing the interface's bInterfaceNumber to find_iad()
instead.

Signed-off-by: Daniel Mack 
Reported-by: bEN 
Reported-by: Ivan Perrone 
Tested-by: ivan perrone 
Signed-off-by: Greg Kroah-Hartman

USB: serial: Enforce USB driver and USB serial driver match

2012-06-22T18:34:16+00:00

commit 954c3f8a5f1b7716be9eee978b3bc85bae92d7c8 upstream.

We need to make sure that the USB serial driver we find
matches the USB driver whose probe we are currently
executing. Otherwise we will end up with USB serial
devices bound to the correct serial driver but wrong
USB driver.

An example of such cross-probing, where the usbserial_generic
USB driver has found the sierra serial driver:

May 29 18:26:15 nemi kernel: [ 4442.559246] usbserial_generic 4-4:1.0: Sierra USB modem converter detected
May 29 18:26:20 nemi kernel: [ 4447.556747] usbserial_generic 4-4:1.2: Sierra USB modem converter detected
May 29 18:26:25 nemi kernel: [ 4452.557288] usbserial_generic 4-4:1.3: Sierra USB modem converter detected

sysfs view of the same problem:

bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root    0 May 29 18:23 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root    0 May 29 18:23 module -> ../../../../module/sierra
-rw-r--r-- 1 root root 4096 May 29 18:23 new_id
lrwxrwxrwx 1 root root    0 May 29 18:32 ttyUSB0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0/ttyUSB0
lrwxrwxrwx 1 root root    0 May 29 18:32 ttyUSB1 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2/ttyUSB1
lrwxrwxrwx 1 root root    0 May 29 18:32 ttyUSB2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3/ttyUSB2
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind

bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/usbserial_generic/
total 0
lrwxrwxrwx 1 root root    0 May 29 18:33 4-4:1.0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0
lrwxrwxrwx 1 root root    0 May 29 18:33 4-4:1.2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2
lrwxrwxrwx 1 root root    0 May 29 18:33 4-4:1.3 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root    0 May 29 18:33 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/generic/
total 0
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root    0 May 29 18:33 module -> ../../../../module/usbserial
-rw-r--r-- 1 root root 4096 May 29 18:33 new_id
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind

So we end up with a mismatch between the USB driver and the
USB serial driver.  The reason for the above is simple: The
USB driver probe will succeed if *any* registered serial
driver matches, and will use that serial driver for all
serial driver functions.

This makes ref counting go wrong. We count the USB driver
as used, but not the USB serial driver.  This may result
in Oops'es as demonstrated by Johan Hovold :

[11811.646396] drivers/usb/serial/usb-serial.c: get_free_serial 1
[11811.646443] drivers/usb/serial/usb-serial.c: get_free_serial - minor base = 0
[11811.646460] drivers/usb/serial/usb-serial.c: usb_serial_probe - registering ttyUSB0
[11811.646766] usb 6-1: pl2303 converter now attached to ttyUSB0
[11812.264197] USB Serial deregistering driver FTDI USB Serial Device
[11812.264865] usbcore: deregistering interface driver ftdi_sio
[11812.282180] USB Serial deregistering driver pl2303
[11812.283141] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[11812.283272] usbcore: deregistering interface driver pl2303
[11812.301056] USB Serial deregistering driver generic
[11812.301186] usbcore: deregistering interface driver usbserial_generic
[11812.301259] drivers/usb/serial/usb-serial.c: usb_serial_disconnect
[11812.301823] BUG: unable to handle kernel paging request at f8e7438c
[11812.301845] IP: [] usb_serial_disconnect+0xb5/0x100 [usbserial]
[11812.301871] *pde = 357ef067 *pte = 00000000
[11812.301957] Oops: 0000 [#1] PREEMPT SMP
[11812.301983] Modules linked in: usbserial(-) [last unloaded: pl2303]
[11812.302008]
[11812.302019] Pid: 1323, comm: modprobe Tainted: G        W    3.4.0-rc7+ #101 Dell Inc. Vostro 1520/0T816J
[11812.302115] EIP: 0060:[] EFLAGS: 00010246 CPU: 1
[11812.302130] EIP is at usb_serial_disconnect+0xb5/0x100 [usbserial]
[11812.302141] EAX: f508a180 EBX: f508a180 ECX: 00000000 EDX: f8e74300
[11812.302151] ESI: f5050800 EDI: 00000001 EBP: f5141e78 ESP: f5141e58
[11812.302160]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[11812.302170] CR0: 8005003b CR2: f8e7438c CR3: 34848000 CR4: 000007d0
[11812.302180] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[11812.302189] DR6: ffff0ff0 DR7: 00000400
[11812.302199] Process modprobe (pid: 1323, ti=f5140000 task=f61e2bc0 task.ti=f5140000)
[11812.302209] Stack:
[11812.302216]  f8e3be0f f8e3b29c f8e3ae00 00000000 f513641c f5136400 f513641c f507a540
[11812.302325]  f5141e98 c133d2c1 00000000 00000000 f509c400 f513641c f507a590 f5136450
[11812.302372]  f5141ea8 c12f0344 f513641c f507a590 f5141ebc c12f0c67 00000000 f507a590
[11812.302419] Call Trace:
[11812.302439]  [] usb_unbind_interface+0x51/0x190
[11812.302456]  [] __device_release_driver+0x64/0xb0
[11812.302469]  [] driver_detach+0x97/0xa0
[11812.302483]  [] bus_remove_driver+0x6c/0xe0
[11812.302500]  [] ? __mutex_unlock_slowpath+0xcd/0x140
[11812.302514]  [] driver_unregister+0x49/0x80
[11812.302528]  [] ? printk+0x1d/0x1f
[11812.302540]  [] usb_deregister+0x5d/0xb0
[11812.302557]  [] ? usb_serial_deregister+0x45/0x50 [usbserial]
[11812.302575]  [] usb_serial_deregister_drivers+0x2d/0x40 [usbserial]
[11812.302593]  [] usb_serial_generic_deregister+0x12/0x20 [usbserial]
[11812.302611]  [] usb_serial_exit+0x8/0x32 [usbserial]
[11812.302716]  [] sys_delete_module+0x158/0x260
[11812.302730]  [] ? mntput+0x1e/0x30
[11812.302746]  [] ? sysenter_exit+0xf/0x18
[11812.302746]  [] ? trace_hardirqs_on_caller+0xec/0x170
[11812.302746]  [] sysenter_do_call+0x12/0x36
[11812.302746] Code: 24 02 00 00 e8 dd f3 20 c8 f6 86 74 02 00 00 02 74 b4 8d 86 4c 02 00 00 47 e8 78 55 4b c8 0f b6 43 0e 39 f8 7f a9 8b 53 04 89 d8  92 8c 00 00 00 89 d8 e8 0e ff ff ff 8b 45 f0 c7 44 24 04 2f
[11812.302746] EIP: [] usb_serial_disconnect+0xb5/0x100 [usbserial] SS:ESP 0068:f5141e58
[11812.302746] CR2: 00000000f8e7438c

Fix by only evaluating serial drivers pointing back to the
USB driver we are currently probing.  This still allows two
or more drivers to match the same device, running their
serial driver probes to sort out which one to use.

Signed-off-by: Bjørn Mork 
Reviewed-by: Felipe Balbi 
Tested-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: serial: sierra: Add support for Sierra Wireless AirCard 320U modem

2012-06-22T18:34:15+00:00

commit 19a3dd1575e954e8c004413bee3e12d3962f2525 upstream.

Add support for Sierra Wireless AirCard 320U modem

Signed-off-by: Tomas Cassidy 
Signed-off-by: Greg Kroah-Hartman