linux-stable.git/drivers/usb, branch linux-5.4.y Linux kernel stable tree usb: xhci: plat: Facilitate using autosuspend for xhci plat devices 2025-12-03T11:45:13+00:00 Krishna Kurapati krishna.kurapati@oss.qualcomm.com 2025-09-16T12:04:36+00:00 ac91ada020c161f8a60d16d54568750d5ec0204a [ Upstream commit 41cf11946b9076383a2222bbf1ef57d64d033f66 ] Allow autosuspend to be used by xhci plat device. For Qualcomm SoCs, when in host mode, it is intended that the controller goes to suspend state to save power and wait for interrupts from connected peripheral to wake it up. This is particularly used in cases where a HID or Audio device is connected. In such scenarios, the usb controller can enter auto suspend and resume action after getting interrupts from the connected device. Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250916120436.3617598-1-krishna.kurapati@oss.qualcomm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 41cf11946b9076383a2222bbf1ef57d64d033f66 ]

Allow autosuspend to be used by xhci plat device. For Qualcomm SoCs,
when in host mode, it is intended that the controller goes to suspend
state to save power and wait for interrupts from connected peripheral
to wake it up. This is particularly used in cases where a HID or Audio
device is connected. In such scenarios, the usb controller can enter
auto suspend and resume action after getting interrupts from the
connected device.

Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250916120436.3617598-1-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usb: mon: Increase BUFF_MAX to 64 MiB to support multi-MB URBs 2025-12-03T11:45:12+00:00 Forest Crossman cyrozap@gmail.com 2025-09-15T19:55:10+00:00 e9d2ab8795d1bbced2b6b2a8accc6713e2de9333 [ Upstream commit 368ed48a5ef52e384f54d5809f0a0b79ac567479 ] The usbmon binary interface currently truncates captures of large transfers from higher-speed USB devices. Because a single event capture is limited to one-fifth of the total buffer size, the current maximum size of a captured URB is around 240 KiB. This is insufficient when capturing traffic from modern devices that use transfers of several hundred kilobytes or more, as truncated URBs can make it impossible for user-space USB analysis tools like Wireshark to properly defragment and reassemble higher-level protocol packets in the captured data. The root cause of this issue is the 1200 KiB BUFF_MAX limit, which has not been changed since the binary interface was introduced in 2006. To resolve this issue, this patch increases BUFF_MAX to 64 MiB. The original comment for BUFF_MAX based the limit's calculation on a saturated 480 Mbit/s bus. Applying the same logic to a modern USB 3.2 Gen 2×2 20 Gbit/s bus (~2500 MB/s over a 20ms window) indicates the buffer should be at least 50 MB. The new limit of 64 MiB covers that, plus a little extra for any overhead. With this change, both users and developers should now be able to debug and reverse engineer modern USB devices even when running unmodified distro kernels. Please note that this change does not affect the default buffer size. A larger buffer is only allocated when a user explicitly requests it via the MON_IOCT_RING_SIZE ioctl, so the change to the maximum buffer size should not unduly increase memory usage for users that don't deliberately request a larger buffer. Link: https://lore.kernel.org/CAO3ALPzdUkmMr0YMrODLeDSLZqNCkWcAP8NumuPHLjNJ8wC1kQ@mail.gmail.com Signed-off-by: Forest Crossman <cyrozap@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/CAO3ALPxU5RzcoueC454L=WZ1qGMfAcnxm+T+p+9D8O9mcrUbCQ@mail.gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 368ed48a5ef52e384f54d5809f0a0b79ac567479 ]

The usbmon binary interface currently truncates captures of large
transfers from higher-speed USB devices. Because a single event capture
is limited to one-fifth of the total buffer size, the current maximum
size of a captured URB is around 240 KiB. This is insufficient when
capturing traffic from modern devices that use transfers of several
hundred kilobytes or more, as truncated URBs can make it impossible for
user-space USB analysis tools like Wireshark to properly defragment and
reassemble higher-level protocol packets in the captured data.

The root cause of this issue is the 1200 KiB BUFF_MAX limit, which has
not been changed since the binary interface was introduced in 2006.

To resolve this issue, this patch increases BUFF_MAX to 64 MiB. The
original comment for BUFF_MAX based the limit's calculation on a
saturated 480 Mbit/s bus. Applying the same logic to a modern USB 3.2
Gen 2×2 20 Gbit/s bus (~2500 MB/s over a 20ms window) indicates the
buffer should be at least 50 MB. The new limit of 64 MiB covers that,
plus a little extra for any overhead.

With this change, both users and developers should now be able to debug
and reverse engineer modern USB devices even when running unmodified
distro kernels.

Please note that this change does not affect the default buffer size. A
larger buffer is only allocated when a user explicitly requests it via
the MON_IOCT_RING_SIZE ioctl, so the change to the maximum buffer size
should not unduly increase memory usage for users that don't
deliberately request a larger buffer.

Link: https://lore.kernel.org/CAO3ALPzdUkmMr0YMrODLeDSLZqNCkWcAP8NumuPHLjNJ8wC1kQ@mail.gmail.com
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/CAO3ALPxU5RzcoueC454L=WZ1qGMfAcnxm+T+p+9D8O9mcrUbCQ@mail.gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usb: gadget: f_hid: Fix zero length packet transfer 2025-12-03T11:45:11+00:00 William Wu william.wu@rock-chips.com 2025-08-26T10:28:07+00:00 3248107d00948c55c5475c3efcd02ee75aaf185b [ Upstream commit ed6f727c575b1eb8136e744acfd5e7306c9548f6 ] Set the hid req->zero flag of ep0/in_ep to true by default, then the UDC drivers can transfer a zero length packet at the end if the hid transfer with size divisible to EPs max packet size according to the USB 2.0 spec. Signed-off-by: William Wu <william.wu@rock-chips.com> Link: https://lore.kernel.org/r/1756204087-26111-1-git-send-email-william.wu@rock-chips.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit ed6f727c575b1eb8136e744acfd5e7306c9548f6 ]

Set the hid req->zero flag of ep0/in_ep to true by default,
then the UDC drivers can transfer a zero length packet at
the end if the hid transfer with size divisible to EPs max
packet size according to the USB 2.0 spec.

Signed-off-by: William Wu <william.wu@rock-chips.com>
Link: https://lore.kernel.org/r/1756204087-26111-1-git-send-email-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usb: gadget: f_ncm: Fix MAC assignment NCM ethernet 2025-12-03T11:45:09+00:00 raub camaioni raubcameo@gmail.com 2025-08-15T13:07:21+00:00 a3f918b791cd8dd143845376ae0d58c32506b714 [ Upstream commit 956606bafb5fc6e5968aadcda86fc0037e1d7548 ] This fix is already present in f_ecm.c and was never propagated to f_ncm.c When creating multiple NCM ethernet devices on a composite usb gadget device each MAC address on the HOST side will be identical. Having the same MAC on different network interfaces is bad. This fix updates the MAC address inside the ncm_strings_defs global during the ncm_bind call. This ensures each device has a unique MAC. In f_ecm.c ecm_string_defs is updated in the same way. The defunct MAC assignment in ncm_alloc has been removed. Signed-off-by: raub camaioni <raubcameo@gmail.com> Link: https://lore.kernel.org/r/20250815131358.1047525-1-raubcameo@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 956606bafb5fc6e5968aadcda86fc0037e1d7548 ]

This fix is already present in f_ecm.c and was never
propagated to f_ncm.c

When creating multiple NCM ethernet devices
on a composite usb gadget device
each MAC address on the HOST side will be identical.
Having the same MAC on different network interfaces is bad.

This fix updates the MAC address inside the
ncm_strings_defs global during the ncm_bind call.
This ensures each device has a unique MAC.
In f_ecm.c ecm_string_defs is updated in the same way.

The defunct MAC assignment in ncm_alloc has been removed.

Signed-off-by: raub camaioni <raubcameo@gmail.com>
Link: https://lore.kernel.org/r/20250815131358.1047525-1-raubcameo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usb: gadget: f_fs: Fix epfile null pointer access after ep enable. 2025-12-03T11:45:06+00:00 Owen Gu guhuinan@xiaomi.com 2025-09-15T09:29:07+00:00 b00d2572c16e8e59e979960d3383c2ae9cebd195 commit cfd6f1a7b42f62523c96d9703ef32b0dbc495ba4 upstream. A race condition occurs when ffs_func_eps_enable() runs concurrently with ffs_data_reset(). The ffs_data_clear() called in ffs_data_reset() sets ffs->epfiles to NULL before resetting ffs->eps_count to 0, leading to a NULL pointer dereference when accessing epfile->ep in ffs_func_eps_enable() after successful usb_ep_enable(). The ffs->epfiles pointer is set to NULL in both ffs_data_clear() and ffs_data_close() functions, and its modification is protected by the spinlock ffs->eps_lock. And the whole ffs_func_eps_enable() function is also protected by ffs->eps_lock. Thus, add NULL pointer handling for ffs->epfiles in the ffs_func_eps_enable() function to fix issues Signed-off-by: Owen Gu <guhuinan@xiaomi.com> Link: https://lore.kernel.org/r/20250915092907.17802-1-guhuinan@xiaomi.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit cfd6f1a7b42f62523c96d9703ef32b0dbc495ba4 upstream.

A race condition occurs when ffs_func_eps_enable() runs concurrently
with ffs_data_reset(). The ffs_data_clear() called in ffs_data_reset()
sets ffs->epfiles to NULL before resetting ffs->eps_count to 0, leading
to a NULL pointer dereference when accessing epfile->ep in
ffs_func_eps_enable() after successful usb_ep_enable().

The ffs->epfiles pointer is set to NULL in both ffs_data_clear() and
ffs_data_close() functions, and its modification is protected by the
spinlock ffs->eps_lock. And the whole ffs_func_eps_enable() function
is also protected by ffs->eps_lock.

Thus, add NULL pointer handling for ffs->epfiles in the
ffs_func_eps_enable() function to fix issues

Signed-off-by: Owen Gu <guhuinan@xiaomi.com>
Link: https://lore.kernel.org/r/20250915092907.17802-1-guhuinan@xiaomi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: dbc: enable back DbC in resume if it was enabled before suspend 2025-10-29T13:00:00+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2025-10-13T22:55:42+00:00 428c8047526a047e885bb0643a19369ff1941728 commit 2bbd38fcd29670e46c0fdb9cd0e90507a8a1bf6a upstream. DbC is currently only enabled back if it's in configured state during suspend. If system is suspended after DbC is enabled, but before the device is properly enumerated by the host, then DbC would not be enabled back in resume. Always enable DbC back in resume if it's suspended in enabled, connected, or configured state Cc: stable <stable@kernel.org> Fixes: dfba2174dc42 ("usb: xhci: Add DbC support in xHCI driver") Tested-by: Łukasz Bartosik <ukaszb@chromium.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2bbd38fcd29670e46c0fdb9cd0e90507a8a1bf6a upstream.

DbC is currently only enabled back if it's in configured state during
suspend.

If system is suspended after DbC is enabled, but before the device is
properly enumerated by the host, then DbC would not be enabled back in
resume.

Always enable DbC back in resume if it's suspended in enabled,
connected, or configured state

Cc: stable <stable@kernel.org>
Fixes: dfba2174dc42 ("usb: xhci: Add DbC support in xHCI driver")
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb/core/quirks: Add Huawei ME906S to wakeup quirk 2025-10-29T13:00:00+00:00 Tim Guttzeit t.guttzeit@tuxedocomputers.com 2025-10-20T13:39:04+00:00 02a089cf404203dc6efdf26aed0d5cef819bde67 commit dfc2cf4dcaa03601cd4ca0f7def88b2630fca6ab upstream. The list of Huawei LTE modules needing the quirk fixing spurious wakeups was missing the IDs of the Huawei ME906S module, therefore suspend did not work. Cc: stable <stable@kernel.org> Signed-off-by: Tim Guttzeit <t.guttzeit@tuxedocomputers.com> Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Link: https://patch.msgid.link/20251020134304.35079-1-wse@tuxedocomputers.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit dfc2cf4dcaa03601cd4ca0f7def88b2630fca6ab upstream.

The list of Huawei LTE modules needing the quirk fixing spurious wakeups
was missing the IDs of the Huawei ME906S module, therefore suspend did not
work.

Cc: stable <stable@kernel.org>
Signed-off-by: Tim Guttzeit <t.guttzeit@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://patch.msgid.link/20251020134304.35079-1-wse@tuxedocomputers.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: option: add Telit FN920C04 ECM compositions 2025-10-29T13:00:00+00:00 LI Qingwu Qing-wu.Li@leica-geosystems.com.cn 2025-10-23T03:44:22+00:00 2b24cd3ab1c71e96629578d762a3df062dd0770c commit 622865c73ae30f254abdf182f4b66cccbe3e0f10 upstream. Add support for the Telit Cinterion FN920C04 module when operating in ECM (Ethernet Control Model) mode. The following USB product IDs are used by the module when AT#USBCFG is set to 3 or 7. 0x10A3: ECM + tty (NMEA) + tty (DUN) [+ tty (DIAG)] T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10a3 Rev= 5.15 S: Manufacturer=Telit Cinterion S: Product=FN920 S: SerialNumber=76e7cb38 C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms 0x10A8: ECM + tty (DUN) + tty (AUX) [+ tty (DIAG)] T: Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10a8 Rev= 5.15 S: Manufacturer=Telit Cinterion S: Product=FN920 S: SerialNumber=76e7cb38 C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Adding these IDs allows the option driver to automatically create the corresponding /dev/ttyUSB* ports under ECM mode. Tested with FN920C04 under ECM configuration (USBCFG=3 and 7). Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 622865c73ae30f254abdf182f4b66cccbe3e0f10 upstream.

Add support for the Telit Cinterion FN920C04 module when operating in
ECM (Ethernet Control Model) mode. The following USB product IDs are
used by the module when AT#USBCFG is set to 3 or 7.

0x10A3: ECM + tty (NMEA) + tty (DUN) [+ tty (DIAG)]
T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10a3 Rev= 5.15
S:  Manufacturer=Telit Cinterion
S:  Product=FN920
S:  SerialNumber=76e7cb38
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E:  Ad=82(I) Atr=03(Int.) MxPS=  16 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

0x10A8: ECM + tty (DUN) + tty (AUX) [+ tty (DIAG)]
T:  Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10a8 Rev= 5.15
S:  Manufacturer=Telit Cinterion
S:  Product=FN920
S:  SerialNumber=76e7cb38
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E:  Ad=82(I) Atr=03(Int.) MxPS=  16 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Adding these IDs allows the option driver to automatically create the
corresponding /dev/ttyUSB* ports under ECM mode.

Tested with FN920C04 under ECM configuration (USBCFG=3 and 7).

Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: option: add Quectel RG255C 2025-10-29T13:00:00+00:00 Reinhard Speyerer rspmn@arcor.de 2025-10-22T14:17:26+00:00 e9639d4237e8c8521792d49322cc8db9ee14fe5a commit 89205c60c0fc96b73567a2e9fe27ee3f59d01193 upstream. Add support for Quectel RG255C devices to complement commit 5c964c8a97c1 ("net: usb: qmi_wwan: add Quectel RG255C"). The composition is DM / NMEA / AT / QMI. T: Bus=01 Lev=02 Prnt=99 Port=01 Cnt=02 Dev#=110 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0316 Rev= 5.15 S: Manufacturer=Quectel S: Product=RG255C-GL S: SerialNumber=xxxxxxxx C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Reinhard Speyerer <rspmn@arcor.de> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 89205c60c0fc96b73567a2e9fe27ee3f59d01193 upstream.

Add support for Quectel RG255C devices to complement commit 5c964c8a97c1
("net: usb: qmi_wwan: add Quectel RG255C").
The composition is DM / NMEA / AT / QMI.

T:  Bus=01 Lev=02 Prnt=99 Port=01 Cnt=02 Dev#=110 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0316 Rev= 5.15
S:  Manufacturer=Quectel
S:  Product=RG255C-GL
S:  SerialNumber=xxxxxxxx
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E:  Ad=86(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: option: add UNISOC UIS7720 2025-10-29T13:00:00+00:00 Renjun Wang renjunw0@foxmail.com 2025-10-19T10:44:38+00:00 84c73088ec0d12f24ed347bf7e0a86bd0b2367ea commit 71c07570b918f000de5d0f7f1bf17a2887e303b5 upstream. Add support for UNISOC (Spreadtrum) UIS7720 (A7720) module. T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1782 ProdID=4064 Rev=04.04 S: Manufacturer=Unisoc-phone S: Product=Unisoc-phone S: SerialNumber=0123456789ABCDEF C: #Ifs= 9 Cfg#= 1 Atr=c0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms 0&1: RNDIS, 2: LOG, 3: DIAG, 4&5: AT Ports, 6&7: AT2 Ports, 8: ADB Signed-off-by: Renjun Wang <renjunw0@foxmail.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 71c07570b918f000de5d0f7f1bf17a2887e303b5 upstream.

Add support for UNISOC (Spreadtrum) UIS7720 (A7720) module.

T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  5 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1782 ProdID=4064 Rev=04.04
S:  Manufacturer=Unisoc-phone
S:  Product=Unisoc-phone
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 9 Cfg#= 1 Atr=c0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

0&1: RNDIS, 2: LOG, 3: DIAG, 4&5: AT Ports, 6&7: AT2 Ports, 8: ADB

Signed-off-by: Renjun Wang <renjunw0@foxmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>