linux-stable.git/drivers/usb/typec, branch v5.4.124

usb: typec: tcpm: Fix error while calculating PPS out values

2021-05-19T08:08:33+00:00

commit 374157ff88ae1a7f7927331cbc72c1ec11994e8a upstream.

"usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply"
introduced a regression for req_out_volt and req_op_curr calculation.

req_out_volt should consider the newly calculated max voltage instead
of previously accepted max voltage by the port partner. Likewise,
req_op_curr should consider the newly calculated max current instead
of previously accepted max current by the port partner.

Fixes: e3a072022487 ("usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply")
Reviewed-by: Guenter Roeck 
Signed-off-by: Badhri Jagan Sridharan 
Link: https://lore.kernel.org/r/20210415050121.1928298-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman

usb: typec: tcpci: Check ROLE_CONTROL while interpreting CC_STATUS

2021-05-14T07:44:17+00:00

[ Upstream commit 19c234a14eafca78e0bc14ffb8be3891096ce147 ]

While interpreting CC_STATUS, ROLE_CONTROL has to be read to make
sure that CC1/CC2 is not forced presenting Rp/Rd.

>From the TCPCI spec:

4.4.5.2 ROLE_CONTROL (Normative):
The TCPM shall write B6 (DRP) = 0b and B3..0 (CC1/CC2) if it wishes
to control the Rp/Rd directly instead of having the TCPC perform
DRP toggling autonomously. When controlling Rp/Rd directly, the
TCPM writes to B3..0 (CC1/CC2) each time it wishes to change the
CC1/CC2 values. This control is used for TCPM-TCPC implementing
Source or Sink only as well as when a connection has been detected
via DRP toggling but the TCPM wishes to attempt Try.Src or Try.Snk.

Table 4-22. CC_STATUS Register Definition:
If (ROLE_CONTROL.CC1 = Rd) or ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp-1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp-3.0A

If (ROLE_CONTROL.CC2=Rd) or (ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp 1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp 3.0A

Fixes: 74e656d6b0551 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Acked-by: Heikki Krogerus 
Signed-off-by: Badhri Jagan Sridharan 
Link: https://lore.kernel.org/r/20210304070931.1947316-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: typec: tcpm: update power supply once partner accepts

2021-05-14T07:44:11+00:00

commit 4050f2683f2c3151dc3dd1501ac88c57caf810ff upstream.

power_supply_changed needs to be called to notify clients
after the partner accepts the requested values for the pps
case.

Also, remove the redundant power_supply_changed at the end
of the tcpm_reset_port as power_supply_changed is already
called right after usb_type is changed.

Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan 
Cc: stable 
Reviewed-by: Adam Thomson 
Reviewed-by: Heikki Krogerus 
Link: https://lore.kernel.org/r/20210407200723.1914388-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman

usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply

2021-05-14T07:44:11+00:00

commit e3a0720224873587954b55d193d5b4abb14f0443 upstream.

tcpm_pd_select_pps_apdo overwrites port->pps_data.min_volt,
port->pps_data.max_volt, port->pps_data.max_curr even before
port partner accepts the requests. This leaves incorrect values
in current_limit and supply_voltage that get exported by
"tcpm-source-psy-". Solving this problem by caching the request
values in req_min_volt, req_max_volt, req_max_curr, req_out_volt,
req_op_curr. min_volt, max_volt, max_curr gets updated once the
partner accepts the request. current_limit, supply_voltage gets updated
once local port's tcpm enters SNK_TRANSITION_SINK when the accepted
current_limit and supply_voltage is enforced.

Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan 
Cc: stable 
Reviewed-by: Adam Thomson 
Reviewed-by: Heikki Krogerus 
Link: https://lore.kernel.org/r/20210407200723.1914388-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman

usb: typec: tcpm: Address incorrect values of tcpm psy for fixed supply

2021-05-14T07:44:11+00:00

commit f3dedafb8263ca4791a92a23f5230068f5bde008 upstream.

tcpm_pd_build_request overwrites current_limit and supply_voltage
even before port partner accepts the requests. This leaves stale
values in current_limit and supply_voltage that get exported by
"tcpm-source-psy-". Solving this problem by caching the request
values of current limit/supply voltage in req_current_limit
and req_supply_voltage. current_limit/supply_voltage gets updated
once the port partner accepts the request.

Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan 
Cc: stable 
Reviewed-by: Guenter Roeck 
Reviewed-by: Adam Thomson 
Reviewed-by: Heikki Krogerus 
Link: https://lore.kernel.org/r/20210407200723.1914388-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman

usb: typec: tcpm: Invoke power_supply_changed for tcpm-source-psy-

2021-03-24T10:26:41+00:00

commit 86629e098a077922438efa98dc80917604dfd317 upstream.

tcpm-source-psy- does not invoke power_supply_changed API when
one of the published power supply properties is changed.
power_supply_changed needs to be called to notify
userspace clients(uevents) and kernel clients.

Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Reviewed-by: Guenter Roeck 
Reviewed-by: Heikki Krogerus 
Signed-off-by: Badhri Jagan Sridharan 
Cc: stable 
Link: https://lore.kernel.org/r/20210317181249.1062995-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman

usb: typec: Fix copy paste error for NVIDIA alt-mode description

2021-01-19T17:26:16+00:00

[ Upstream commit 41952a66015466c3208aac96b14ffd92e0943589 ]

The name of the module for the NVIDIA alt-mode is incorrect as it
looks to be a copy-paste error from the entry above, update it to
the correct typec_nvidia module name.

Cc: Ajay Gupta 
Cc: Heikki Krogerus 
Signed-off-by: Peter Robinson 
Link: https://lore.kernel.org/r/20210106001605.167917-1-pbrobinson@gmail.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: typec: tcpm: reset hard_reset_count for any disconnect

2020-11-05T10:43:28+00:00

commit 2d9c6442a9c81f4f8dee678d0b3c183173ab1e2d upstream.

Current tcpm_detach() only reset hard_reset_count if port->attached
is true, this may cause this counter clear is missed if the CC
disconnect event is generated after tcpm_port_reset() is done
by other events, e.g. VBUS off comes first before CC disconect for
a power sink, in that case the first tcpm_detach() will only clear
port->attached flag but leave hard_reset_count there because
tcpm_port_is_disconnected() is still false, then later tcpm_detach()
by CC disconnect will directly return due to port->attached is cleared,
finally this will result tcpm will not try hard reset or error recovery
for later attach.

ChiYuan reported this issue on his platform with below tcpm trace:
After power sink session setup after hard reset 2 times, detach
from the power source and then attach:
[ 4848.046358] VBUS off
[ 4848.046384] state change SNK_READY -> SNK_UNATTACHED
[ 4848.050908] Setting voltage/current limit 0 mV 0 mA
[ 4848.050936] polarity 0
[ 4848.052593] Requesting mux state 0, usb-role 0, orientation 0
[ 4848.053222] Start toggling
[ 4848.086500] state change SNK_UNATTACHED -> TOGGLING
[ 4848.089983] CC1: 0 -> 0, CC2: 3 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.089993] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.090031] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.141162] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.141170] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.141184] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.163156] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 20 ms]
[ 4848.163162] Start toggling
[ 4848.216918] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.216954] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.217080] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.231771] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.231800] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.231857] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.256022] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed20 ms]
[ 4848.256049] Start toggling
[ 4848.871148] VBUS on
[ 4848.885324] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.885372] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.885548] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4849.088240] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed200 ms]
[ 4849.088284] state change SNK_DEBOUNCED -> SNK_ATTACHED
[ 4849.088291] polarity 1
[ 4849.088769] Requesting mux state 1, usb-role 2, orientation 2
[ 4849.088895] state change SNK_ATTACHED -> SNK_STARTUP
[ 4849.088907] state change SNK_STARTUP -> SNK_DISCOVERY
[ 4849.088915] Setting voltage/current limit 5000 mV 0 mA
[ 4849.088927] vbus=0 charge:=1
[ 4849.090505] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES
[ 4849.090828] pending state change SNK_WAIT_CAPABILITIES -> SNK_READY @240 ms
[ 4849.335878] state change SNK_WAIT_CAPABILITIES -> SNK_READY [delayed240 ms]

this patch fix this issue by clear hard_reset_count at any cases
of cc disconnect, í.e. don't check port->attached flag.

Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging")
Cc: stable@vger.kernel.org
Reported-and-tested-by: ChiYuan Huang 
Reviewed-by: Guenter Roeck 
Reviewed-by: Heikki Krogerus 
Signed-off-by: Li Jun 
Link: https://lore.kernel.org/r/1602500592-3817-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman

usb: typec: tcpm: During PR_SWAP, source caps should be sent only after tSwapSourceStart

2020-11-05T10:43:15+00:00

[ Upstream commit 6bbe2a90a0bb4af8dd99c3565e907fe9b5e7fd88 ]

The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.

The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.

This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."

The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after  tSwapSourceStart(20ms).

Signed-off-by: Badhri Jagan Sridharan 
Reviewed-by: Guenter Roeck 
Reviewed-by: Heikki Krogerus 
Link: https://lore.kernel.org/r/20200817183828.1895015-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: typec: ucsi: Prevent mode overrun

2020-09-23T10:40:44+00:00

commit 386e15a650447f53de3d2d8819ce9393f31650a4 upstream.

Sometimes the embedded controller firmware does not
terminate the list of alternate modes that the partner
supports in its response to the GET_ALTERNATE_MODES command.
Instead the firmware returns the supported alternate modes
over and over again until the driver stops requesting them.

If that happens, the number of modes for each alternate mode
will exceed the maximum 6 that is defined in the USB Power
Delivery specification. Making sure that can't happen by
adding a check for it.

This fixes NULL pointer dereference that is caused by the
overrun.

Fixes: ad74b8649beaf ("usb: typec: ucsi: Preliminary support for alternate modes")
Cc: stable@vger.kernel.org
Reported-by: Zwane Mwaikambo 
Signed-off-by: Heikki Krogerus 
Link: https://lore.kernel.org/r/20200916090034.25119-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman