linux-stable.git/drivers/usb/typec, branch v4.19.201 Linux kernel stable tree usb: typec: Add the missed altmode_id_remove() in typec_register_altmode() 2021-07-20T14:15:39+00:00 Jing Xiangfeng jingxiangfeng@huawei.com 2021-06-17T07:32:26+00:00 9c7de678190ac6d48e51633584075d045901b580 commit 03026197bb657d784220b040c6173267a0375741 upstream. typec_register_altmode() misses to call altmode_id_remove() in an error path. Add the missed function call to fix it. Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes") Cc: stable <stable@vger.kernel.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com> Link: https://lore.kernel.org/r/20210617073226.47599-1-jingxiangfeng@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 03026197bb657d784220b040c6173267a0375741 upstream.

typec_register_altmode() misses to call altmode_id_remove() in an error
path. Add the missed function call to fix it.

Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes")
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Link: https://lore.kernel.org/r/20210617073226.47599-1-jingxiangfeng@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: typec: ucsi: Clear PPM capability data in ucsi_init() error path 2021-06-16T09:55:00+00:00 Mayank Rana mrana@codeaurora.org 2021-06-09T07:35:35+00:00 83ca9ae4e03bb04f2abc1d8d78a1fed9760fd251 commit f247f0a82a4f8c3bfed178d8fd9e069d1424ee4e upstream. If ucsi_init() fails for some reason (e.g. ucsi_register_port() fails or general communication failure to the PPM), particularly at any point after the GET_CAPABILITY command had been issued, this results in unwinding the initialization and returning an error. However the ucsi structure's ucsi_capability member retains its current value, including likely a non-zero num_connectors. And because ucsi_init() itself is done in a workqueue a UCSI interface driver will be unaware that it failed and may think the ucsi_register() call was completely successful. Later, if ucsi_unregister() is called, due to this stale ucsi->cap value it would try to access the items in the ucsi->connector array which might not be in a proper state or not even allocated at all and results in NULL or invalid pointer dereference. Fix this by clearing the ucsi->cap value to 0 during the error path of ucsi_init() in order to prevent a later ucsi_unregister() from entering the connector cleanup loop. Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface") Cc: stable@vger.kernel.org Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Mayank Rana <mrana@codeaurora.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Link: https://lore.kernel.org/r/20210609073535.5094-1-jackp@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit f247f0a82a4f8c3bfed178d8fd9e069d1424ee4e upstream.

If ucsi_init() fails for some reason (e.g. ucsi_register_port()
fails or general communication failure to the PPM), particularly at
any point after the GET_CAPABILITY command had been issued, this
results in unwinding the initialization and returning an error.
However the ucsi structure's ucsi_capability member retains its
current value, including likely a non-zero num_connectors.
And because ucsi_init() itself is done in a workqueue a UCSI
interface driver will be unaware that it failed and may think the
ucsi_register() call was completely successful.  Later, if
ucsi_unregister() is called, due to this stale ucsi->cap value it
would try to access the items in the ucsi->connector array which
might not be in a proper state or not even allocated at all and
results in NULL or invalid pointer dereference.

Fix this by clearing the ucsi->cap value to 0 during the error
path of ucsi_init() in order to prevent a later ucsi_unregister()
from entering the connector cleanup loop.

Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210609073535.5094-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: typec: tcpci: Check ROLE_CONTROL while interpreting CC_STATUS 2021-05-22T08:59:27+00:00 Badhri Jagan Sridharan badhri@google.com 2021-03-04T07:09:31+00:00 8af6ecdb60c5648ad6090903d294589dee6aadff [ Upstream commit 19c234a14eafca78e0bc14ffb8be3891096ce147 ] While interpreting CC_STATUS, ROLE_CONTROL has to be read to make sure that CC1/CC2 is not forced presenting Rp/Rd. >From the TCPCI spec: 4.4.5.2 ROLE_CONTROL (Normative): The TCPM shall write B6 (DRP) = 0b and B3..0 (CC1/CC2) if it wishes to control the Rp/Rd directly instead of having the TCPC perform DRP toggling autonomously. When controlling Rp/Rd directly, the TCPM writes to B3..0 (CC1/CC2) each time it wishes to change the CC1/CC2 values. This control is used for TCPM-TCPC implementing Source or Sink only as well as when a connection has been detected via DRP toggling but the TCPM wishes to attempt Try.Src or Try.Snk. Table 4-22. CC_STATUS Register Definition: If (ROLE_CONTROL.CC1 = Rd) or ConnectResult=1) 00b: SNK.Open (Below maximum vRa) 01b: SNK.Default (Above minimum vRd-Connect) 10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp-1.5A 11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp-3.0A If (ROLE_CONTROL.CC2=Rd) or (ConnectResult=1) 00b: SNK.Open (Below maximum vRa) 01b: SNK.Default (Above minimum vRd-Connect) 10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp 1.5A 11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp 3.0A Fixes: 74e656d6b0551 ("staging: typec: Type-C Port Controller Interface driver (tcpci)") Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Badhri Jagan Sridharan <badhri@google.com> Link: https://lore.kernel.org/r/20210304070931.1947316-1-badhri@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 19c234a14eafca78e0bc14ffb8be3891096ce147 ]

While interpreting CC_STATUS, ROLE_CONTROL has to be read to make
sure that CC1/CC2 is not forced presenting Rp/Rd.

>From the TCPCI spec:

4.4.5.2 ROLE_CONTROL (Normative):
The TCPM shall write B6 (DRP) = 0b and B3..0 (CC1/CC2) if it wishes
to control the Rp/Rd directly instead of having the TCPC perform
DRP toggling autonomously. When controlling Rp/Rd directly, the
TCPM writes to B3..0 (CC1/CC2) each time it wishes to change the
CC1/CC2 values. This control is used for TCPM-TCPC implementing
Source or Sink only as well as when a connection has been detected
via DRP toggling but the TCPM wishes to attempt Try.Src or Try.Snk.

Table 4-22. CC_STATUS Register Definition:
If (ROLE_CONTROL.CC1 = Rd) or ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp-1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp-3.0A

If (ROLE_CONTROL.CC2=Rd) or (ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp 1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp 3.0A

Fixes: 74e656d6b0551 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210304070931.1947316-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usb: typec: tcpm: reset hard_reset_count for any disconnect 2020-11-05T10:08:49+00:00 Li Jun jun.li@nxp.com 2020-10-12T11:03:12+00:00 061fae52838ad8e9c59c65859088e3f6f850d5e5 commit 2d9c6442a9c81f4f8dee678d0b3c183173ab1e2d upstream. Current tcpm_detach() only reset hard_reset_count if port->attached is true, this may cause this counter clear is missed if the CC disconnect event is generated after tcpm_port_reset() is done by other events, e.g. VBUS off comes first before CC disconect for a power sink, in that case the first tcpm_detach() will only clear port->attached flag but leave hard_reset_count there because tcpm_port_is_disconnected() is still false, then later tcpm_detach() by CC disconnect will directly return due to port->attached is cleared, finally this will result tcpm will not try hard reset or error recovery for later attach. ChiYuan reported this issue on his platform with below tcpm trace: After power sink session setup after hard reset 2 times, detach from the power source and then attach: [ 4848.046358] VBUS off [ 4848.046384] state change SNK_READY -> SNK_UNATTACHED [ 4848.050908] Setting voltage/current limit 0 mV 0 mA [ 4848.050936] polarity 0 [ 4848.052593] Requesting mux state 0, usb-role 0, orientation 0 [ 4848.053222] Start toggling [ 4848.086500] state change SNK_UNATTACHED -> TOGGLING [ 4848.089983] CC1: 0 -> 0, CC2: 3 -> 3 [state TOGGLING, polarity 0, connected] [ 4848.089993] state change TOGGLING -> SNK_ATTACH_WAIT [ 4848.090031] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms [ 4848.141162] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected] [ 4848.141170] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT [ 4848.141184] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms [ 4848.163156] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 20 ms] [ 4848.163162] Start toggling [ 4848.216918] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected] [ 4848.216954] state change TOGGLING -> SNK_ATTACH_WAIT [ 4848.217080] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms [ 4848.231771] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected] [ 4848.231800] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT [ 4848.231857] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms [ 4848.256022] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed20 ms] [ 4848.256049] Start toggling [ 4848.871148] VBUS on [ 4848.885324] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected] [ 4848.885372] state change TOGGLING -> SNK_ATTACH_WAIT [ 4848.885548] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms [ 4849.088240] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed200 ms] [ 4849.088284] state change SNK_DEBOUNCED -> SNK_ATTACHED [ 4849.088291] polarity 1 [ 4849.088769] Requesting mux state 1, usb-role 2, orientation 2 [ 4849.088895] state change SNK_ATTACHED -> SNK_STARTUP [ 4849.088907] state change SNK_STARTUP -> SNK_DISCOVERY [ 4849.088915] Setting voltage/current limit 5000 mV 0 mA [ 4849.088927] vbus=0 charge:=1 [ 4849.090505] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [ 4849.090828] pending state change SNK_WAIT_CAPABILITIES -> SNK_READY @240 ms [ 4849.335878] state change SNK_WAIT_CAPABILITIES -> SNK_READY [delayed240 ms] this patch fix this issue by clear hard_reset_count at any cases of cc disconnect, í.e. don't check port->attached flag. Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging") Cc: stable@vger.kernel.org Reported-and-tested-by: ChiYuan Huang <cy_huang@richtek.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Li Jun <jun.li@nxp.com> Link: https://lore.kernel.org/r/1602500592-3817-1-git-send-email-jun.li@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2d9c6442a9c81f4f8dee678d0b3c183173ab1e2d upstream.

Current tcpm_detach() only reset hard_reset_count if port->attached
is true, this may cause this counter clear is missed if the CC
disconnect event is generated after tcpm_port_reset() is done
by other events, e.g. VBUS off comes first before CC disconect for
a power sink, in that case the first tcpm_detach() will only clear
port->attached flag but leave hard_reset_count there because
tcpm_port_is_disconnected() is still false, then later tcpm_detach()
by CC disconnect will directly return due to port->attached is cleared,
finally this will result tcpm will not try hard reset or error recovery
for later attach.

ChiYuan reported this issue on his platform with below tcpm trace:
After power sink session setup after hard reset 2 times, detach
from the power source and then attach:
[ 4848.046358] VBUS off
[ 4848.046384] state change SNK_READY -> SNK_UNATTACHED
[ 4848.050908] Setting voltage/current limit 0 mV 0 mA
[ 4848.050936] polarity 0
[ 4848.052593] Requesting mux state 0, usb-role 0, orientation 0
[ 4848.053222] Start toggling
[ 4848.086500] state change SNK_UNATTACHED -> TOGGLING
[ 4848.089983] CC1: 0 -> 0, CC2: 3 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.089993] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.090031] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.141162] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.141170] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.141184] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.163156] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 20 ms]
[ 4848.163162] Start toggling
[ 4848.216918] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.216954] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.217080] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.231771] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.231800] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.231857] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.256022] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed20 ms]
[ 4848.256049] Start toggling
[ 4848.871148] VBUS on
[ 4848.885324] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.885372] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.885548] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4849.088240] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed200 ms]
[ 4849.088284] state change SNK_DEBOUNCED -> SNK_ATTACHED
[ 4849.088291] polarity 1
[ 4849.088769] Requesting mux state 1, usb-role 2, orientation 2
[ 4849.088895] state change SNK_ATTACHED -> SNK_STARTUP
[ 4849.088907] state change SNK_STARTUP -> SNK_DISCOVERY
[ 4849.088915] Setting voltage/current limit 5000 mV 0 mA
[ 4849.088927] vbus=0 charge:=1
[ 4849.090505] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES
[ 4849.090828] pending state change SNK_WAIT_CAPABILITIES -> SNK_READY @240 ms
[ 4849.335878] state change SNK_WAIT_CAPABILITIES -> SNK_READY [delayed240 ms]

this patch fix this issue by clear hard_reset_count at any cases
of cc disconnect, í.e. don't check port->attached flag.

Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging")
Cc: stable@vger.kernel.org
Reported-and-tested-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1602500592-3817-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: typec: tcpm: During PR_SWAP, source caps should be sent only after tSwapSourceStart 2020-11-05T10:08:40+00:00 Badhri Jagan Sridharan badhri@google.com 2020-08-17T18:38:27+00:00 00943757170b126923ade6e705cbf532327e4989 [ Upstream commit 6bbe2a90a0bb4af8dd99c3565e907fe9b5e7fd88 ] The patch addresses the compliance test failures while running TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD Compliance MOI" test plan published in https://www.usb.org/usbc. For a product to be Type-C compliant, it's expected that these tests are run on usb.org certified Type-C compliance tester as mentioned in https://www.usb.org/usbc. The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to verify the PR_SWAP response of the device. While doing so, the test asserts that Source Capabilities message is NOT received from the test device within tSwapSourceStart min (20 ms) from the time the last bit of GoodCRC corresponding to the RS_RDY message sent by the UUT was sent. If it does then the test fails. This is in line with the requirements from the USB Power Delivery Specification Revision 3.0, Version 1.2: "6.6.8.1 SwapSourceStartTimer The SwapSourceStartTimer Shall be used by the new Source, after a Power Role Swap or Fast Role Swap, to ensure that it does not send Source_Capabilities Message before the new Sink is ready to receive the Source_Capabilities Message. The new Source Shall Not send the Source_Capabilities Message earlier than tSwapSourceStart after the last bit of the EOP of GoodCRC Message sent in response to the PS_RDY Message sent by the new Source indicating that its power supply is ready." The patch makes sure that TCPM does not send the Source_Capabilities Message within tSwapSourceStart(20ms) by transitioning into SRC_STARTUP only after tSwapSourceStart(20ms). Signed-off-by: Badhri Jagan Sridharan <badhri@google.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200817183828.1895015-1-badhri@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 6bbe2a90a0bb4af8dd99c3565e907fe9b5e7fd88 ]

The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.

The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.

This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."

The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after  tSwapSourceStart(20ms).

Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200817183828.1895015-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usb: typec: ucsi: acpi: Check the _DEP dependencies 2020-09-17T11:45:31+00:00 Heikki Krogerus heikki.krogerus@linux.intel.com 2020-09-04T11:09:18+00:00 923e11ef2afa63e2a637f1e5ff989e8197c95f58 commit 1f3546ff3f0a1000971daef58406954bad3f7061 upstream. Failing probe with -EPROBE_DEFER until all dependencies listed in the _DEP (Operation Region Dependencies) object have been met. This will fix an issue where on some platforms UCSI ACPI driver fails to probe because the address space handler for the operation region that the UCSI ACPI interface uses has not been loaded yet. Fixes: 8243edf44152 ("usb: typec: ucsi: Add ACPI driver") Cc: stable@vger.kernel.org Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 1f3546ff3f0a1000971daef58406954bad3f7061 upstream.

Failing probe with -EPROBE_DEFER until all dependencies
listed in the _DEP (Operation Region Dependencies) object
have been met.

This will fix an issue where on some platforms UCSI ACPI
driver fails to probe because the address space handler for
the operation region that the UCSI ACPI interface uses has
not been loaded yet.

Fixes: 8243edf44152 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: typec: tcpci_rt1711h: avoid screaming irq causing boot hangs 2020-07-01T03:17:08+00:00 Li Jun jun.li@nxp.com 2020-06-04T11:21:18+00:00 4309ab96ab744703871e35d829177dd9347bf643 commit 302c570bf36e997d55ad0d60628a2feec76954a4 upstream. John reported screaming irq caused by rt1711h when system boot[1], this is because irq request is done before tcpci_register_port(), so the chip->tcpci has not been setup, irq handler is entered but can't do anything, this patch is to address this by moving the irq request after tcpci_register_port(). [1] https://lore.kernel.org/linux-usb/20200530040157.31038-1-john.stultz@linaro.org Fixes: ce08eaeb6388 ("staging: typec: rt1711h typec chip driver") Cc: stable <stable@vger.kernel.org> # v4.18+ Cc: John Stultz <john.stultz@linaro.org> Reported-and-tested-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Li Jun <jun.li@nxp.com> Link: https://lore.kernel.org/r/20200604112118.38062-1-jun.li@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 302c570bf36e997d55ad0d60628a2feec76954a4 upstream.

John reported screaming irq caused by rt1711h when system boot[1],
this is because irq request is done before tcpci_register_port(),
so the chip->tcpci has not been setup, irq handler is entered but
can't do anything, this patch is to address this by moving the irq
request after tcpci_register_port().

[1] https://lore.kernel.org/linux-usb/20200530040157.31038-1-john.stultz@linaro.org

Fixes: ce08eaeb6388 ("staging: typec: rt1711h typec chip driver")
Cc: stable <stable@vger.kernel.org> # v4.18+
Cc: John Stultz <john.stultz@linaro.org>
Reported-and-tested-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20200604112118.38062-1-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: typec: tcpci: mask event interrupts when remove driver 2020-02-11T12:33:55+00:00 Jun Li jun.li@nxp.com 2020-01-20T06:43:19+00:00 1ee531e8048ebc03d08c9a0064930c8b1b541522 commit 3ba76256fc4e2a0d7fb26cc95459041ea0e88972 upstream. This is to prevent any possible events generated while unregister tpcm port. Fixes: 74e656d6b055 ("staging: typec: Type-C Port Controller Interface driver (tcpci)") Signed-off-by: Li Jun <jun.li@nxp.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/1579502333-4145-1-git-send-email-jun.li@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 3ba76256fc4e2a0d7fb26cc95459041ea0e88972 upstream.

This is to prevent any possible events generated while unregister
tpcm port.

Fixes: 74e656d6b055 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1579502333-4145-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: typec: tps6598x: Fix build error without CONFIG_REGMAP_I2C 2020-01-27T13:51:09+00:00 YueHaibing yuehaibing@huawei.com 2019-09-03T12:10:26+00:00 2404a2e35aaf74add564abfdb09273bbffae8ace [ Upstream commit 35af2445dc306403254a181507b390ec9eb725d5 ] If CONFIG_REGMAP_I2C is not set, building fails: drivers/usb/typec/tps6598x.o: In function `tps6598x_probe': tps6598x.c:(.text+0x5f0): undefined reference to `__devm_regmap_init_i2c' Select REGMAP_I2C to fix this. Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 0a4c005bd171 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20190903121026.22148-1-yuehaibing@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 35af2445dc306403254a181507b390ec9eb725d5 ]

If CONFIG_REGMAP_I2C is not set, building fails:

drivers/usb/typec/tps6598x.o: In function `tps6598x_probe':
tps6598x.c:(.text+0x5f0): undefined reference to `__devm_regmap_init_i2c'

Select REGMAP_I2C to fix this.

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0a4c005bd171 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190903121026.22148-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usb: typec: tcpm: Notify the tcpc to start connection-detection for SRPs 2020-01-27T13:50:40+00:00 Hans de Goede hdegoede@redhat.com 2019-04-16T20:07:52+00:00 da4c428a8209dcccb5b83ad4d4bae660e2adce76 [ Upstream commit 7893f9e1c26d1f9ea02622902ee671de45ad377b ] Some tcpc device-drivers need to explicitly be told to watch for connection events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices being plugged into the Type-C port will not be noticed. For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to watch for connection events. Sofar we lack a similar callback to the tcpc for single-role ports. With some tcpc-s such as the fusb302 this means no TCPM_CC_EVENTs will be generated when the port is configured as a single-role port. This commit renames start_drp_toggling to start_toggling and since the device-properties are parsed by the tcpm-core, adds a port_type parameter to the start_toggling callback so that the tcpc_dev driver knows the port-type and can act accordingly when it starts toggling. The new start_toggling callback now always gets called if defined, instead of only being called for DRP ports. To avoid this causing undesirable functional changes all existing start_drp_toggling implementations are not only renamed to start_toggling, but also get a port_type check added and return -EOPNOTSUPP when port_type is not DRP. Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...") Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 7893f9e1c26d1f9ea02622902ee671de45ad377b ]

Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.

For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. Sofar we lack a similar callback to the tcpc
for single-role ports. With some tcpc-s such as the fusb302 this means
no TCPM_CC_EVENTs will be generated when the port is configured as a
single-role port.

This commit renames start_drp_toggling to start_toggling and since the
device-properties are parsed by the tcpm-core, adds a port_type parameter
to the start_toggling callback so that the tcpc_dev driver knows the
port-type and can act accordingly when it starts toggling.

The new start_toggling callback now always gets called if defined, instead
of only being called for DRP ports.

To avoid this causing undesirable functional changes all existing
start_drp_toggling implementations are not only renamed to start_toggling,
but also get a port_type check added and return -EOPNOTSUPP when port_type
is not DRP.

Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...")
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>