linux-stable.git/drivers/usb/typec/Makefile, branch v5.10

usb: typec: Add QCOM PMIC typec detection driver

2020-10-09T13:14:43+00:00

The QCOM SPMI typec driver handles the role and orientation detection, and
notifies client drivers using the USB role switch framework.   It registers
as a typec port, so orientation can be communicated using the typec switch
APIs.  The driver also attains a handle to the VBUS output regulator, so it
can enable/disable the VBUS source when acting as a host/device.

Signed-off-by: Wesley Cheng 
Acked-by: Heikki Krogerus 
Reviewed-by: Stephen Boyd 
Link: https://lore.kernel.org/r/20201008235934.8931-2-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman

usb: typec: add support for STUSB160x Type-C controller family

2020-10-02T13:30:31+00:00

STMicroelectronics USB Type-C port controllers use I2C interface to
configure, control and read the operation status of the device. All ST USB
Type-C port controllers are based on the same I2C register map. That's why
this driver can be used with all ST USB Type-C ICs.
Some ST USB Type-C port controllers are Dual Role Port (DRP), only Sink or
Source, some supports USB Power Delivery. This can be configured through
connector device tree bindings.

This driver is a basic Type-C port controller driver, with no power
delivery support. It allows to configure ST USB Type-C port controller.
Interrupt is supported and enables CC connection events, to detect
attach and detach and update Type-C subsystem accordingly as well as usb
role switch.

ST USB Type-C port controller can be supplied in three different ways
depending on the target application:
- through VDD pin only (so VDD is the main supply)
- through VSYS pin only (so VSYS is the main supply)
- through VDD and VSYS pins.
When both VDD and VSYS power supplies are present, the low power supply
VSYS is selected as main supply when VSYS voltage is above 3.1V, else
VDD is selected as main supply.

In case of Source or Dual port type, if VDD supply is present, it has to be
enabled in case of Source power role to provide Vbus. When interrupt
support is available, VDD supply is dynamically managed upon attach/detach
interrupt. When there is no interrupt support, VDD supply is enabled by
default.

Acked-by: Heikki Krogerus 
Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20200924090049.9041-5-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman

usb: typec: driver for TI HD3SS3220 USB Type-C DRP port controller

2019-10-04T12:18:48+00:00

Driver for TI HD3SS3220 USB Type-C DRP port controller.

The driver currently registers the port and supports data role swapping.

Signed-off-by: Biju Das 
Acked-by: Heikki Krogerus 
Link: https://lore.kernel.org/r/1567584941-13690-3-git-send-email-biju.das@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman

usb: typec: Group all TCPCI/TCPM code together

2018-09-20T11:37:29+00:00

Moving all the drivers that depend on the Port Controller
Manager under a new directory drivers/usb/typec/tcpm/ and
making Guenter Roeck the designated reviewer of that code.

Acked-by: Guenter Roeck 
Signed-off-by: Heikki Krogerus 
Signed-off-by: Greg Kroah-Hartman

usb: typec: Add driver for DisplayPort alternate mode

2018-07-02T15:42:36+00:00

DisplayPort USB Type-C Alt Mode allows DisplayPort displays
and adapters to be attached to the USB Type-C ports on the
system.

Signed-off-by: Heikki Krogerus 
Tested-by: Hans de Goede 
Signed-off-by: Greg Kroah-Hartman

usb: typec: Bus type for alternate modes

2018-07-02T15:42:36+00:00

Introducing a simple bus for the alternate modes. Bus allows
binding drivers to the discovered alternate modes the
partners support.

Signed-off-by: Heikki Krogerus 
Tested-by: Hans de Goede 
Signed-off-by: Greg Kroah-Hartman

staging: typec: tcpci: move tcpci drivers out of staging

2018-06-28T10:49:48+00:00

Move TCPCI(Typec port controller interface) driver and rt1711h
driver out of staging.

Signed-off-by: Li Jun 
Reviewed-by: Guenter Roeck 
Acked-by: Heikki Krogerus 
Signed-off-by: Greg Kroah-Hartman

usb: typec: driver for Pericom PI3USB30532 Type-C cross switch

2018-03-22T12:49:28+00:00

Add a driver for the Pericom PI3USB30532 Type-C cross switch /
mux chip found on some devices with a Type-C port.

Signed-off-by: Hans de Goede 
Reviewed-by: Andy Shevchenko 
Signed-off-by: Heikki Krogerus 
Signed-off-by: Greg Kroah-Hartman

usb: typec: API for controlling USB Type-C Multiplexers

2018-03-22T12:40:10+00:00

USB Type-C connectors consist of various muxes and switches
that route the pins on the connector to the right locations.
The USB Type-C drivers need to be able to control the muxes,
as they are the ones that know things like the cable plug
orientation, and the current mode that was negotiated with
the partner.

This introduces a small API for registering and controlling
cable plug orientation switches, and separate small API for
registering and controlling pin multiplexer/demultiplexer
switches that are needed with Accessory/Alternate Modes.

Reviewed-by: Hans de Goede 
Reviewed-by: Andy Shevchenko 
Signed-off-by: Heikki Krogerus 
Signed-off-by: Greg Kroah-Hartman

USB: add SPDX identifiers to all remaining Makefiles

2017-11-07T14:53:48+00:00

It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.

This updates the remaining drivers/usb/*Makefile* that were missing SPDX
identifiers.  They all get the following identifier:
	SPDX-License-Identifier: GPL-2.0

The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.

Cc: Thomas Gleixner 
Cc: Kate Stewart 
Cc: Philippe Ombredanne 
Cc: Peter Korsgaard 
Cc: Thomas Winischhofer 
Cc: Johan Hovold 
Acked-by: Heikki Krogerus 
Signed-off-by: Greg Kroah-Hartman