commit a541acceedf4f639f928f41fbb676b75946dc295 upstream.
SanDisk 3.2 Gen2 storage device(0781:55e8) doesn't work well with UAS.
Log says,
[ 6.507865][ 3] [ T159] usb 2-1.4: new SuperSpeed Gen 1 USB device number 4 using xhci_hcd
[ 6.540314][ 3] [ T159] usb 2-1.4: New USB device found, idVendor=0781, idProduct=55e8, bcdDevice= 0.01
[ 6.576304][ 3] [ T159] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.584727][ 3] [ T159] usb 2-1.4: Product: SanDisk 3.2 Gen2
[ 6.590459][ 3] [ T159] usb 2-1.4: Manufacturer: SanDisk
[ 6.595845][ 3] [ T159] usb 2-1.4: SerialNumber: 03021707022525140940
[ 7.230852][ 0] [ T265] usbcore: registered new interface driver usb-storage
[ 7.251247][ 0] [ T265] scsi host3: uas
[ 7.255280][ 0] [ T265] usbcore: registered new interface driver uas
[ 7.270498][ 1] [ T192] scsi 3:0:0:0: Direct-Access SanDisk Extreme Pro DDE1 0110 PQ: 0 ANSI: 6
[ 7.299588][ 3] [ T192] scsi 3:0:0:1: Enclosure SanDisk SES Device 0110 PQ: 0 ANSI: 6
[ 7.321681][ 3] [ T192] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 7.328185][ 3] [ T192] scsi 3:0:0:1: Attached scsi generic sg2 type 13
[ 7.328804][ 0] [ T191] sd 3:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 7.343486][ 0] [ T191] sd 3:0:0:0: [sda] 4096-byte physical blocks
[ 7.364611][ 0] [ T191] sd 3:0:0:0: [sda] Write Protect is off
[ 7.370524][ 0] [ T191] sd 3:0:0:0: [sda] Mode Sense: 3d 00 10 00
[ 7.390655][ 0] [ T191] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 7.401363][ 0] [ T191] sd 3:0:0:0: [sda] Optimal transfer size 1048576 bytes
[ 7.436010][ 0] [ T191] sda: sda1
[ 7.450850][ 0] [ T191] sd 3:0:0:0: [sda] Attached SCSI disk
[ 7.470218][ 4] [ T262] scsi 3:0:0:1: Failed to get diagnostic page 0x1
[ 7.474869][ 0] [ C0] sd 3:0:0:0: [sda] tag#0 data cmplt err -75 uas-tag 2 inflight: CMD
[ 7.476911][ 4] [ T262] scsi 3:0:0:1: Failed to bind enclosure -19
[ 7.485330][ 0] [ C0] sd 3:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 00 00 28 00 00 10 00
[ 7.491593][ 4] [ T262] ses 3:0:0:1: Attached Enclosure device
[ 38.066980][ 4] [ T192] sd 3:0:0:0: [sda] tag#4 uas_eh_abort_handler 0 uas-tag 5 inflight: CMD IN
[ 38.076012][ 4] [ T192] sd 3:0:0:0: [sda] tag#4 CDB: Read(10) 28 00 00 00 01 08 00 00 f8 00
[ 38.086485][ 4] [ T192] sd 3:0:0:0: [sda] tag#3 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[ 38.095515][ 4] [ T192] sd 3:0:0:0: [sda] tag#3 CDB: Read(10) 28 00 00 00 00 10 00 00 08 00
[ 38.104122][ 4] [ T192] sd 3:0:0:0: [sda] tag#2 uas_eh_abort_handler 0 uas-tag 4 inflight: CMD IN
[ 38.113152][ 4] [ T192] sd 3:0:0:0: [sda] tag#2 CDB: Read(10) 28 00 00 00 00 88 00 00 78 00
[ 38.121761][ 4] [ T192] sd 3:0:0:0: [sda] tag#1 uas_eh_abort_handler 0 uas-tag 3 inflight: CMD IN
[ 38.130791][ 4] [ T192] sd 3:0:0:0: [sda] tag#1 CDB: Read(10) 28 00 00 00 00 48 00 00 30 00
[ 38.139401][ 4] [ T192] sd 3:0:0:0: [sda] tag#0 uas_eh_abort_handler 0 uas-tag 2 inflight: CMD
[ 38.148170][ 4] [ T192] sd 3:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 00 00 28 00 00 10 00
[ 38.178980][ 2] [ T304] scsi host3: uas_eh_device_reset_handler start
[ 38.901540][ 2] [ T304] usb 2-1.4: reset SuperSpeed Gen 1 USB device number 4 using xhci_hcd
[ 38.936791][ 2] [ T304] scsi host3: uas_eh_device_reset_handler success
Device decriptor is below,
Bus 002 Device 006: ID 0781:55e8 SanDisk Corp. SanDisk 3.2 Gen2
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.20
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x0781 SanDisk Corp.
idProduct 0x55e8
bcdDevice 0.01
iManufacturer 1 SanDisk
iProduct 2 SanDisk 3.2 Gen2
iSerial 3 03021707022525140940
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0079
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 896mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 4
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 98
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Command pipe (0x01)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
MaxStreams 32
Status pipe (0x02)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
MaxStreams 32
Data-in pipe (0x03)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
MaxStreams 32
Data-out pipe (0x04)
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 0x002a
bNumDeviceCaps 3
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x0000f41e
BESL Link Power Management (LPM) Supported
BESL value 1024 us
Deep BESL value 61440 us
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 2047 micro seconds
SuperSpeedPlus USB Device Capability:
bLength 20
bDescriptorType 16
bDevCapabilityType 10
bmAttributes 0x00000001
Sublink Speed Attribute count 1
Sublink Speed ID count 0
wFunctionalitySupport 0x1100
bmSublinkSpeedAttr[0] 0x000a4030
Speed Attribute ID: 0 10Gb/s Symmetric RX SuperSpeedPlus
bmSublinkSpeedAttr[1] 0x000a40b0
Speed Attribute ID: 0 10Gb/s Symmetric TX SuperSpeedPlus
Device Status: 0x0000
(Bus Powered)
So ignore UAS driver for this device.
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250519023328.1498856-1-xiehongyu1@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ab75eee1a056f896b87d139044dd103adc532b9 upstream. Version 1.60 specifically needs this quirk. Version 2.00 is known good. Cc: stable <stable@kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20250403180004.343133-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdef30e0774802df2f87024d68a9d86c3b99ca2a upstream. This fixes data corruption when accessing the internal SD card in mass storage mode. I am actually not too sure why. I didn't figure a straightforward way to reproduce the issue, but i seem to get garbage when issuing a lot (over 50) of large reads (over 120 sectors) are done in a quick succession. That is, time seems to matter here -- larger reads are fine if they are done with some delay between them. But I'm not great at understanding this sort of things, so I'll assume the issue other, smarter, folks were seeing with similar phones is the same problem and I'll just put my quirk next to theirs. The "Software details" screen on the phone is as follows: V 04.06 07-08-13 RM-849 (c) Nokia TL;DR version of the device descriptor: idVendor 0x0421 Nokia Mobile Phones idProduct 0x06c2 bcdDevice 4.06 iManufacturer 1 Nokia iProduct 2 Nokia 208 The patch assumes older firmwares are broken too (I'm unable to test, but no biggie if they aren't I guess), and I have no idea if newer firmware exists. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Cc: stable <stable@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20250101212206.2386207-1-lkundrak@v3.sk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6555cb1cb69db479d0760e392c175ba32426842 upstream. JieLi tends to use SCSI via USB Mass Storage to implement their own proprietary commands instead of implementing another USB interface. Enumerating it as a generic mass storage device will lead to a Hardware Error sense key get reported. Ignore this bogus device to prevent appearing a unusable sdX device file. Signed-off-by: Icenowy Zheng <uwu@icenowy.me> Cc: stable <stable@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20241001083407.8336-1-uwu@icenowy.me Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d32685a251a754f1823d287df233716aa23bcb9 ] Set the host status byte when a data completion error is encountered otherwise the upper layer may end up using the invalid zero'ed data. The following output was observed from scsi/sd.c prior to this fix. [ 11.872824] sd 0:0:0:1: [sdf] tag#9 data cmplt err -75 uas-tag 1 inflight: [ 11.872826] sd 0:0:0:1: [sdf] tag#9 CDB: Read capacity(16) 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00 [ 11.872830] sd 0:0:0:1: [sdf] Sector size 0 reported, assuming 512. Signed-off-by: Shantanu Goel <sgoel01@yahoo.com> Acked-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/87msnx4ec6.fsf@yahoo.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16637fea001ab3c8df528a8995b3211906165a30 ]
The member "uzonesize" of struct alauda_info will remain 0
if alauda_init_media() fails, potentially causing divide errors
in alauda_read_data() and alauda_write_lba().
- Add a member "media_initialized" to struct alauda_info.
- Change a condition in alauda_check_media() to ensure the
first initialization.
- Add an error check for the return value of alauda_init_media().
Fixes: e80b0fade09e ("[PATCH] USB Storage: add alauda support")
Reported-by: xingwei lee <xrivendell7@gmail.com>
Reported-by: yue sun <samsun1006219@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Shichao Lai <shichaorai@gmail.com>
Link: https://lore.kernel.org/r/20240526012745.2852061-1-shichaorai@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 014bcf41d946b36a8f0b8e9b5d9529efbb822f49 upstream.
The isd200 sub-driver in usb-storage uses the HEADS and SECTORS values
in the ATA ID information to calculate cylinder and head values when
creating a CDB for READ or WRITE commands. The calculation involves
division and modulus operations, which will cause a crash if either of
these values is 0. While this never happens with a genuine device, it
could happen with a flawed or subversive emulation, as reported by the
syzbot fuzzer.
Protect against this possibility by refusing to bind to the device if
either the ATA_ID_HEADS or ATA_ID_SECTORS value in the device's ID
information is 0. This requires isd200_Initialization() to return a
negative error code when initialization fails; currently it always
returns 0 (even when there is an error).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+28748250ab47a8f04100@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-usb/0000000000003eb868061245ba7f@google.com/
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/b1e605ea-333f-4ac0-9511-da04f411763e@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e3139e6543b241b3e65956a55c712333bef48ac upstream. Change lower bcdDevice value for "Super Top USB 2.0 SATA BRIDGE" to match 1.50. I have such an older device with bcdDevice=1.50 and it will not work otherwise. Cc: stable@vger.kernel.org Signed-off-by: Liha Sikanen <lihasika@gmail.com> Link: https://lore.kernel.org/r/ccf7d12a-8362-4916-b3e0-f4150f54affd@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6ff6e7a9dd69364547751db0f626a10a6d628d2 upstream.
Syzbot got KMSAN to complain about access to an uninitialized value in
the alauda subdriver of usb-storage:
BUG: KMSAN: uninit-value in alauda_transport+0x462/0x57f0
drivers/usb/storage/alauda.c:1137
CPU: 0 PID: 12279 Comm: usb-storage Not tainted 5.3.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x13a/0x2b0 mm/kmsan/kmsan_report.c:108
__msan_warning+0x73/0xe0 mm/kmsan/kmsan_instr.c:250
alauda_check_media+0x344/0x3310 drivers/usb/storage/alauda.c:460
The problem is that alauda_check_media() doesn't verify that its USB
transfer succeeded before trying to use the received data. What
should happen if the transfer fails isn't entirely clear, but a
reasonably conservative approach is to pretend that no media is
present.
A similar problem exists in a usb_stor_dbg() call in
alauda_get_media_status(). In this case, when an error occurs the
call is redundant, because usb_stor_ctrl_transfer() already will print
a debugging message.
Finally, unrelated to the uninitialized memory access, is the fact
that alauda_check_media() performs DMA to a buffer on the stack.
Fortunately usb-storage provides a general purpose DMA-able buffer for
uses like this. We'll use it instead.
Reported-and-tested-by: syzbot+e7d46eb426883fb97efd@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/0000000000007d25ff059457342d@google.com/T/
Suggested-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: e80b0fade09e ("[PATCH] USB Storage: add alauda support")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/693d5d5e-f09b-42d0-8ed9-1f96cd30bcce@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a398d5eac6984316e71474e25b975688f282379b upstream.
With faulty usb-storage devices, read/write can timeout, in that case
the SCSI layer will abort and re-issue the command. USB storage has no
internal timeout, it relies on SCSI layer aborting commands via
.eh_abort_handler() for non those responsive devices.
After two consecutive timeouts of the same command, SCSI layer calls
.eh_device_reset_handler(), without calling .eh_abort_handler() first.
With usb-storage, this causes a deadlock:
-> .eh_device_reset_handler
-> device_reset
-> mutex_lock(&(us->dev_mutex));
mutex already by usb_stor_control_thread(), which is waiting for
command completion:
-> usb_stor_control_thread (mutex taken here)
-> usb_stor_invoke_transport
-> usb_stor_Bulk_transport
-> usb_stor_bulk_srb
-> usb_stor_bulk_transfer_sglist
-> usb_sg_wait
Make sure we cancel any pending command in .eh_device_reset_handler()
to avoid this.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Cc: linux-usb@vger.kernel.org
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/all/ZEllnjMKT8ulZbJh@sakura/
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230505114759.1189741-1-mbizon@freebox.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>