linux-stable.git/drivers/usb/serial, branch v4.19.9

USB: serial: console: fix reported terminal settings

2018-12-13T08:16:15+00:00

commit f51ccf46217c28758b1f3b5bc0ccfc00eca658b2 upstream.

The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.

Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.

Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().

Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.

This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).

Fixes: 7041d9c3f01b ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable 	# 4.18
Cc: Florian Zumbiehl 
Reported-by: Jarkko Nikula 
Tested-by: Jarkko Nikula 
Acked-by: Greg Kroah-Hartman 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: serial: simple: add Motorola Tetra MTP6550 id

2018-09-24T13:30:16+00:00

Add device-id for the Motorola Tetra radio MTP6550.

Bus 001 Device 004: ID 0cad:9012 Motorola CGISS
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x0cad Motorola CGISS
  idProduct          0x9012
  bcdDevice           24.16
  iManufacturer           1 Motorola Solutions, Inc.
  iProduct                2 TETRA PEI interface
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           55
    bNumInterfaces          2
    bConfigurationValue     1
    iConfiguration          3 Generic Serial config
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              500mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)

Reported-by: Hans Hult 
Cc: stable 
Signed-off-by: Johan Hovold

USB: serial: option: add two-endpoints device-id flag

2018-09-14T08:37:41+00:00

Allow matching on interfaces having two endpoints by adding a new
device-id flag.

This allows for the handling of devices whose interface numbers can
change (e.g. Quectel EP06) to be contained in the device-id table.

Tested-by: Kristian Evensen 
Cc: stable 
Signed-off-by: Johan Hovold

USB: serial: option: improve Quectel EP06 detection

2018-09-14T08:37:41+00:00

The Quectel EP06 (and EM06/EG06) LTE modem supports updating the USB
configuration, without the VID/PID or configuration number changing.
When the configuration is updated and interfaces are added/removed, the
interface numbers are updated. This causes our current code for matching
EP06 not to work as intended, as the assumption about reserved
interfaces no longer holds. If for example the diagnostic (first)
interface is removed, option will (try to) bind to the QMI interface.

This patch improves EP06 detection by replacing the current match with
two matches, and those matches check class, subclass and protocol as
well as VID and PID. The diag interface exports class, subclass and
protocol as 0xff. For the other serial interfaces, class is 0xff and
subclass and protocol are both 0x0.

The modem can export the following devices and always in this order:
diag, nmea, at, ppp. qmi and adb. This means that diag can only ever be
interface 0, and interface numbers 1-5 should be marked as reserved. The
three other serial devices can have interface numbers 0-3, but I have
not marked any interfaces as reserved. The reason is that the serial
devices are the only interfaces exported by the device where subclass
and protocol is 0x0.

QMI exports the same class, subclass and protocol values as the diag
interface. However, the two interfaces have different number of
endpoints, QMI has three and diag two. I have added a check for number
of interfaces if VID/PID matches the EP06, and we ignore the device if
number of interfaces equals three (and subclass is set).

Signed-off-by: Kristian Evensen 
Acked-by: Dan Williams 
[ johan: drop uneeded RSVD(5) for ADB ]
Cc: stable 
Signed-off-by: Johan Hovold

USB: serial: ti_usb_3410_5052: fix array underflow in completion handler

2018-08-27T09:53:19+00:00

Similarly to a recently reported bug in io_ti, a malicious USB device
could set port_number to a negative value and we would underflow the
port array in the interrupt completion handler.

As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable 
Signed-off-by: Johan Hovold

USB: serial: io_ti: fix array underflow in completion handler

2018-08-27T09:52:34+00:00

As reported by Dan Carpenter, a malicious USB device could set
port_number to a negative value and we would underflow the port array in
the interrupt completion handler.

As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable 
Reported-by: Dan Carpenter 
Signed-off-by: Johan Hovold

USB: serial: pl2303: add a new device id for ATEN

2018-08-02T08:37:04+00:00

Signed-off-by: Movie Song 
Cc: Johan Hovold 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: option: add support for DW5821e

2018-07-28T14:49:50+00:00

The device exposes AT, NMEA and DIAG ports in both USB configurations.

The patch explicitly ignores interfaces 0 and 1, as they're bound to
other drivers already; and also interface 6, which is a GNSS interface
for which we don't have a driver yet.

T:  Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 18 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  2
P:  Vendor=413c ProdID=81d7 Rev=03.18
S:  Manufacturer=DELL
S:  Product=DW5821e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

T:  Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  2
P:  Vendor=413c ProdID=81d7 Rev=03.18
S:  Manufacturer=DELL
S:  Product=DW5821e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

Signed-off-by: Aleksander Morgado 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

Merge tag 'usb-serial-4.19-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

2018-07-20T19:47:15+00:00

Johan writes:

USB-serial updates for v4.19-rc1

Here are the USB-serial updates for 4.19-rc1, including:

 - gpio support for CP2102N devices
 - improved line-speed handling for cp210x
 - conversion to spin_lock_irqsave() in completion handlers
 - dropped kl5kusb105 support from the kl5kusb105 driver (sic!)

Included are also various lower-priority fixes and clean ups.

All but the final commit have been in linux-next, and with no reported
issues.

Signed-off-by: Johan Hovold

USB: serial: cp210x: implement GPIO support for CP2102N

2018-07-20T16:22:52+00:00

This patch adds GPIO support for CP2102N devices.

It introduces new generic code to support emulating separate
input and outputs directions even though these devices
only know output modes (open-drain and pushpull). Existing
GPIO support for CP2105 has been migrated over to the new
code structure.

Only limitation is that for the QFN28 variant, only 4 out of
7 GPIOs are supported. This is because the config array
locations of the last 3 pins are not documented, and reverse
engineering revealed offsets that conflicted with other
documented functions. Hence we'll play it safe instead
until somebody clears this up further.

Signed-off-by: Karoly Pados 
[ johan: fix style issues and a couple of minor bugs; use Karoly's
         updated commit message ]
Acked-by: Martyn Welch 
Signed-off-by: Johan Hovold