commit 6caf0be40a707689e8ff8824fdb96ef77685b1ba upstream. On Motorola Mapphone devices such as Droid 4 there are five USB ports that do not use the same layout as Gobi 1K/2K/etc devices listed in qcserial.c. So we should use qcaux.c or option.c as noted by Dan Williams <dan.j.williams@intel.com>. As the Motorola USB serial ports have an interrupt endpoint as shown with lsusb -v, we should use option.c instead of qcaux.c as pointed out by Johan Hovold <johan@kernel.org>. The ff/ff/ff interfaces seem to always be UARTs on Motorola devices. For the other interfaces, class 0x0a (CDC Data) should not in general be added as they are typically part of a multi-interface function as noted earlier by Bjørn Mork <bjorn@mork.no>. However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a class is only used for flashing the modem firmware, and there are no other interfaces. So I've added that too with more details below as it works just fine. The ttyUSB ports on Droid 4 are: ttyUSB0 DIAG, CQDM-capable ttyUSB1 MUX or NMEA, no response ttyUSB2 MUX or NMEA, no response ttyUSB3 TCMD ttyUSB4 AT-capable The ttyUSB0 is detected as QCDM capable by ModemManager. I think it's only used for debugging with ModemManager --debug for sending custom AT commands though. ModemManager already can manage data connection using the USB QMI ports that are already handled by the qmi_wwan.c driver. To enable the MUX or NMEA ports, it seems that something needs to be done additionally to enable them, maybe via the DIAG or TCMD port. It might be just a NVRAM setting somewhere, but I have no idea what NVRAM settings may need changing for that. The TCMD port seems to be a Motorola custom protocol for testing the modem and to configure it's NVRAM and seems to work just fine based on a quick test with a minimal tcmdrw tool I wrote. The voice modem AT-capable port seems to provide only partial support, and no PM support compared to the TS 27.010 based UART wired directly to the modem. The UARTs added with this change are the same product IDs as the Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't have any mdm9600 based devices, so I have only tested these on mdm6600 based droid 4. Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android Linux kernel driver moto_flashqsc.c just seems to change the port->bulk_out_size to 8K from the default. And is only used for flashing the modem firmware it seems. I've verified that flashing the modem with signed firmware works just fine with the option driver after manually toggling the GPIO pins, so I've added droid 4 modem flashing mode to the option driver. I've not added the other devices listed in moto_flashqsc.c in case they really need different port->bulk_out_size. Those can be added as they get tested to work for flashing the modem. After this patch the output of /sys/kernel/debug/usb/devices has the following for normal 22b8:2a70 mode including the related qmi_wwan interfaces: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=2a70 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms In 22b8:900e "qc_dload" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=900e Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms And in 22b8:4281 "ram_downloader" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=4281 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms Cc: Bjørn Mork <bjorn@mork.no> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Lars Melin <larsm17@gmail.com> Cc: Marcel Partap <mpartap@gmx.net> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Michael Scott <hashcode0f@gmail.com> Cc: NeKit <nekit1000@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Tested-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7e7ae38bf928c5cfa6dd6e9a2cf8b42c84a27c92 upstream. This patch adds support for MF871A USB modem (aka Speed USB STICK U03) to option driver. This modem is manufactured by ZTE corporation, and sold by KDDI. Interface layout: 0: AT 1: MODEM usb-devices output: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 9 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=1481 Rev=52.87 S: Manufacturer=ZTE,Incorporated S: Product=ZTE Technologies MSM S: SerialNumber=1234567890ABCDEF C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option Co-developed-by: Hiroyuki Yamamoto <hyamamo@allied-telesis.co.jp> Signed-off-by: Hiroyuki Yamamoto <hyamamo@allied-telesis.co.jp> Signed-off-by: Yoshiaki Okamoto <yokamoto@allied-telesis.co.jp> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f8377eff548170e8ea8022c067a1fbdf9e1c46a8 upstream. This adds the vid:pid of the isodebug v1 isolated JTAG/SWD+UART. Only the second channel is available for use as a serial port. Signed-off-by: Andreas Fritiofson <andreas.fritiofson@unjo.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit aed2a26283528fb69c38e414f649411aa48fb391 upstream. Added USB IDs for GosunCn ME3630 cellular module in RNDIS mode. T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=03 Dev#= 18 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=0601 Rev=03.18 S: Manufacturer=Android S: Product=Android S: SerialNumber=b950269c C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 70a7444c550a75584ffcfae95267058817eff6a7 upstream. Added USB serial option driver support for GosunCn ZTE WeLink ME3630 series cellular modules for USB modes ECM/NCM and MBIM. usb-devices output MBIM mode: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=0602 Rev=03.18 S: Manufacturer=Android S: Product=Android S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim usb-devices output ECM/NCM mode: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=1476 Rev=03.18 S: Manufacturer=Android S: Product=Android S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> [bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c5f81656a18b271976a86724dadd8344e54de74e upstream. This is adds the vendor and device id for the AT-VT-Kit3 which is a pl2303-based device. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3f5edd58d040bfa4b74fb89bc02f0bc6b9cd06ab upstream.
Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().
First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.
CPU 1 CPU 2
================ ================
complete() unthrottle()
process_urb();
smp_mb__before_atomic();
set_bit(i, free); if (test_and_clear_bit(i, free))
submit_urb();
Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.
CPU 1 CPU 2
================ ================
complete() unthrottle()
set_bit(i, free); throttled = 0;
smp_mb__after_atomic(); smp_mb();
if (throttled) if (test_and_clear_bit(i, free))
return; submit_urb();
Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.
Fixes: d83b405383c9 ("USB: serial: add support for multiple read urbs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3161da970d38cd6ed2ba8cadec93874d1d06e11e upstream. This patch turns status in a variable read once from the URB. The long term plan is to deliver status to the callback. In addition it makes the code a bit more elegant. Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 579bebe5dd522580019e7b10b07daaf500f9fb1e upstream.
The USB-serial driver init_termios callback is used to override the
default initial terminal settings provided by USB-serial core.
After a bug was fixed in the original implementation introduced by
commit fe1ae7fdd2ee ("tty: USB serial termios bits"), the init_termios
callback was no longer called just once on first use as intended but
rather on every (first) open.
This specifically meant that the terminal settings saved on (final)
close were ignored when reopening a port for drivers overriding the
initial settings.
Also update the outdated function header referring to the creation of
termios objects.
Fixes: 7e29bb4b779f ("usb-serial: fix termios initialization logic")
Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a595ecdd5f60b2d93863cebb07eec7f935839b54 upstream. Lorenz Messtechnik has a device that is controlled by the cp210x driver, so add the device id to the driver. The device id was provided by Silicon-Labs for the devices from this vendor. Reported-by: Uli <t9cpu@web.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>