linux-stable.git/drivers/usb/serial, branch linux-6.14.y Linux kernel stable tree USB: serial: pl2303: add new chip PL2303GC-Q20 and PL2303GT-2AB 2025-06-10T11:15:57+00:00 Charles Yeh charlesyeh522@gmail.com 2025-05-21T13:23:54+00:00 4a047f2abc44fff24b353327487a5d6b284c4aa0 commit d3a889482bd5abf2bbdc1ec3d2d49575aa160c9c upstream. Add new bcd (0x905) to support PL2303GT-2AB (TYPE_HXN). Add new bcd (0x1005) to support PL2303GC-Q20 (TYPE_HXN). Signed-off-by: Charles Yeh <charlesyeh522@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit d3a889482bd5abf2bbdc1ec3d2d49575aa160c9c upstream.

Add new bcd (0x905) to support PL2303GT-2AB (TYPE_HXN).
Add new bcd (0x1005) to support PL2303GC-Q20 (TYPE_HXN).

Signed-off-by: Charles Yeh <charlesyeh522@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: simple: add OWON HDS200 series oscilloscope support 2025-05-02T06:01:53+00:00 Craig Hesling craig@hesling.com 2025-04-08T23:27:03+00:00 e7acbe530de41c04f65ca7d6ca841e322d51a1a2 commit 4cc01410e1c1dd075df10f750775c81d1cb6672b upstream. Add serial support for OWON HDS200 series oscilloscopes and likely many other pieces of OWON test equipment. OWON HDS200 series devices host two USB endpoints, designed to facilitate bidirectional SCPI. SCPI is a predominately ASCII text protocol for test/measurement equipment. Having a serial/tty interface for these devices lowers the barrier to entry for anyone trying to write programs to communicate with them. The following shows the USB descriptor for the OWON HDS272S running firmware V5.7.1: Bus 001 Device 068: ID 5345:1234 Owon PDS6062T Oscilloscope Negotiated speed: Full Speed (12Mbps) Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 [unknown] bDeviceSubClass 0 [unknown] bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x5345 Owon idProduct 0x1234 PDS6062T Oscilloscope bcdDevice 1.00 iManufacturer 1 oscilloscope iProduct 2 oscilloscope iSerial 3 oscilloscope bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 0x0029 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 5 Physical Interface Device bInterfaceSubClass 0 [unknown] bInterfaceProtocol 0 iInterface 0 ** UNRECOGNIZED: 09 21 11 01 00 01 22 5f 00 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 32 Device Status: 0x0000 (Bus Powered) OWON appears to be using the same USB Vendor and Product ID for many of their oscilloscopes. Looking at the discussion about the USB vendor/product ID, in the link bellow, suggests that this VID/PID is shared with VDS, SDS, PDS, and now the HDS series oscilloscopes. Available documentation for these devices seems to indicate that all use a similar SCPI protocol, some with RS232 options. It is likely that this same simple serial setup would work correctly for them all. Link: https://usb-ids.gowdy.us/read/UD/5345/1234 Signed-off-by: Craig Hesling <craig@hesling.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 4cc01410e1c1dd075df10f750775c81d1cb6672b upstream.

Add serial support for OWON HDS200 series oscilloscopes and likely
many other pieces of OWON test equipment.

OWON HDS200 series devices host two USB endpoints, designed to
facilitate bidirectional SCPI. SCPI is a predominately ASCII text
protocol for test/measurement equipment. Having a serial/tty interface
for these devices lowers the barrier to entry for anyone trying to
write programs to communicate with them.

The following shows the USB descriptor for the OWON HDS272S running
firmware V5.7.1:

Bus 001 Device 068: ID 5345:1234 Owon PDS6062T Oscilloscope
Negotiated speed: Full Speed (12Mbps)
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 [unknown]
  bDeviceSubClass         0 [unknown]
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x5345 Owon
  idProduct          0x1234 PDS6062T Oscilloscope
  bcdDevice            1.00
  iManufacturer           1 oscilloscope
  iProduct                2 oscilloscope
  iSerial                 3 oscilloscope
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength       0x0029
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         5 Physical Interface Device
      bInterfaceSubClass      0 [unknown]
      bInterfaceProtocol      0
      iInterface              0
      ** UNRECOGNIZED:  09 21 11 01 00 01 22 5f 00
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval              32
Device Status:     0x0000
  (Bus Powered)

OWON appears to be using the same USB Vendor and Product ID for many
of their oscilloscopes. Looking at the discussion about the USB
vendor/product ID, in the link bellow, suggests that this VID/PID is
shared with VDS, SDS, PDS, and now the HDS series oscilloscopes.
Available documentation for these devices seems to indicate that all
use a similar SCPI protocol, some with RS232 options. It is likely that
this same simple serial setup would work correctly for them all.

Link: https://usb-ids.gowdy.us/read/UD/5345/1234
Signed-off-by: Craig Hesling <craig@hesling.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: option: add Sierra Wireless EM9291 2025-05-02T06:01:53+00:00 Adam Xue zxue@semtech.com 2025-04-14T21:14:37+00:00 c20a4b3c11cbcb38abe1c43f583ccd25184d1608 commit 968e1cbb1f6293c3add9607f80b5ce3d29f57583 upstream. Add Sierra Wireless EM9291. Interface 0: MBIM control 1: MBIM data 3: AT port 4: Diagnostic port T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=90e3 Rev=00.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=Sierra Wireless EM9291 S: SerialNumber=xxxxxxxxxxxxxxxx C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=(none) E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none) E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Adam Xue <zxue@semtech.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 968e1cbb1f6293c3add9607f80b5ce3d29f57583 upstream.

Add Sierra Wireless EM9291.

Interface 0: MBIM control
          1: MBIM data
          3: AT port
          4: Diagnostic port

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1199 ProdID=90e3 Rev=00.06
S:  Manufacturer=Sierra Wireless, Incorporated
S:  Product=Sierra Wireless EM9291
S:  SerialNumber=xxxxxxxxxxxxxxxx
C:  #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=(none)
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Adam Xue <zxue@semtech.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: ftdi_sio: add support for Abacus Electrics Optical Probe 2025-05-02T06:01:52+00:00 Michael Ehrenreich michideep@gmail.com 2025-03-17T05:17:15+00:00 506ae9b0cd4edceeb96d4b7ac72318b33e414705 commit b399078f882b6e5d32da18b6c696cc84b12f90d5 upstream. Abacus Electrics makes optical probes for interacting with smart meters over an optical interface. At least one version uses an FT232B chip (as detected by ftdi_sio) with a custom USB PID, which needs to be added to the list to make the device work in a plug-and-play fashion. Signed-off-by: Michael Ehrenreich <michideep@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit b399078f882b6e5d32da18b6c696cc84b12f90d5 upstream.

Abacus Electrics makes optical probes for interacting with smart meters
over an optical interface.

At least one version uses an FT232B chip (as detected by ftdi_sio) with
a custom USB PID, which needs to be added to the list to make the device
work in a plug-and-play fashion.

Signed-off-by: Michael Ehrenreich <michideep@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: ftdi_sio: add support for Altera USB Blaster 3 2025-03-12T16:51:16+00:00 Boon Khai Ng boon.khai.ng@intel.com 2025-03-12T03:05:44+00:00 18e0885bd2ca738407036434418a26a58394a60e The Altera USB Blaster 3, available as both a cable and an on-board solution, is primarily used for programming and debugging FPGAs. It interfaces with host software such as Quartus Programmer, System Console, SignalTap, and Nios Debugger. The device utilizes either an FT2232 or FT4232 chip. Enabling the support for various configurations of the on-board USB Blaster 3 by including the appropriate VID/PID pairs, allowing it to function as a serial device via ftdi_sio. Note that this check-in does not include support for the cable solution, as it does not support UART functionality. The supported configurations are determined by the hardware design and include: 1) PID 0x6022, FT2232, 1 JTAG port (Port A) + Port B as UART 2) PID 0x6025, FT4232, 1 JTAG port (Port A) + Port C as UART 3) PID 0x6026, FT4232, 1 JTAG port (Port A) + Port C, D as UART 4) PID 0x6029, FT4232, 1 JTAG port (Port B) + Port C as UART 5) PID 0x602a, FT4232, 1 JTAG port (Port B) + Port C, D as UART 6) PID 0x602c, FT4232, 1 JTAG port (Port A) + Port B as UART 7) PID 0x602d, FT4232, 1 JTAG port (Port A) + Port B, C as UART 8) PID 0x602e, FT4232, 1 JTAG port (Port A) + Port B, C, D as UART These configurations allow for flexibility in how the USB Blaster 3 is used, depending on the specific needs of the hardware design. Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> 
The Altera USB Blaster 3, available as both a cable and an on-board
solution, is primarily used for programming and debugging FPGAs.

It interfaces with host software such as Quartus Programmer,
System Console, SignalTap, and Nios Debugger. The device utilizes
either an FT2232 or FT4232 chip.

Enabling the support for various configurations of the on-board
USB Blaster 3 by including the appropriate VID/PID pairs,
allowing it to function as a serial device via ftdi_sio.

Note that this check-in does not include support for the
cable solution, as it does not support UART functionality.
The supported configurations are determined by the
hardware design and include:

1) PID 0x6022, FT2232, 1 JTAG port (Port A) + Port B as UART
2) PID 0x6025, FT4232, 1 JTAG port (Port A) + Port C as UART
3) PID 0x6026, FT4232, 1 JTAG port (Port A) + Port C, D as UART
4) PID 0x6029, FT4232, 1 JTAG port (Port B) + Port C as UART
5) PID 0x602a, FT4232, 1 JTAG port (Port B) + Port C, D as UART
6) PID 0x602c, FT4232, 1 JTAG port (Port A) + Port B as UART
7) PID 0x602d, FT4232, 1 JTAG port (Port A) + Port B, C as UART
8) PID 0x602e, FT4232, 1 JTAG port (Port A) + Port B, C, D as UART

These configurations allow for flexibility in how the USB Blaster 3 is
used, depending on the specific needs of the hardware design.

Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
USB: serial: option: fix Telit Cinterion FE990A name 2025-03-06T11:10:13+00:00 Fabio Porcedda fabio.porcedda@gmail.com 2025-03-04T09:19:39+00:00 6232f0d8e100a26275bbd773fc56a60af2c95322 The correct name for FE990 is FE990A so use it in order to avoid confusion with FE990B. Cc: stable@vger.kernel.org Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> 
The correct name for FE990 is FE990A so use it in order to avoid
confusion with FE990B.

Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
USB: serial: option: add Telit Cinterion FE990B compositions 2025-03-06T11:09:51+00:00 Fabio Porcedda fabio.porcedda@gmail.com 2025-03-04T09:19:38+00:00 4981bb50392b7515b765da28cf8768ce624c2670 Add the following Telit Cinterion FE990B40 compositions: 0x10b0: rmnet + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) + tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10b0 Rev=05.15 S: Manufacturer=Telit Cinterion S: Product=FE990 S: SerialNumber=28c2595e C: #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none) E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms 0x10b1: MBIM + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) + tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10b1 Rev=05.15 S: Manufacturer=Telit Cinterion S: Product=FE990 S: SerialNumber=28c2595e C: #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none) E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms 0x10b2: RNDIS + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) + tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 9 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10b2 Rev=05.15 S: Manufacturer=Telit Cinterion S: Product=FE990 S: SerialNumber=28c2595e C: #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none) E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms 0x10b3: ECM + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) + tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 11 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=10b3 Rev=05.15 S: Manufacturer=Telit Cinterion S: Product=FE990 S: SerialNumber=28c2595e C: #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none) E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Cc: stable@vger.kernel.org Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com> Reviewed-by: Daniele Palmas <dnlplm@gmail.com> [ johan: use USB_DEVICE_AND_INTERFACE_INFO() and sort by protocol ] Signed-off-by: Johan Hovold <johan@kernel.org> 
Add the following Telit Cinterion FE990B40 compositions:

0x10b0: rmnet + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) +
        tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb
T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  7 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10b0 Rev=05.15
S:  Manufacturer=Telit Cinterion
S:  Product=FE990
S:  SerialNumber=28c2595e
C:  #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E:  Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E:  Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

0x10b1: MBIM + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) +
        tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb
T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  8 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10b1 Rev=05.15
S:  Manufacturer=Telit Cinterion
S:  Product=FE990
S:  SerialNumber=28c2595e
C:  #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E:  Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E:  Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

0x10b2: RNDIS + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) +
        tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb
T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  9 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10b2 Rev=05.15
S:  Manufacturer=Telit Cinterion
S:  Product=FE990
S:  SerialNumber=28c2595e
C:  #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E:  Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E:  Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

0x10b3: ECM + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) +
        tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb
T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 11 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10b3 Rev=05.15
S:  Manufacturer=Telit Cinterion
S:  Product=FE990
S:  SerialNumber=28c2595e
C:  #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
E:  Ad=82(I) Atr=03(Int.) MxPS=  16 Ivl=32ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E:  Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E:  Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Reviewed-by: Daniele Palmas <dnlplm@gmail.com>
[ johan: use USB_DEVICE_AND_INTERFACE_INFO() and sort by protocol ]
Signed-off-by: Johan Hovold <johan@kernel.org>
USB: serial: option: match on interface class for Telit FN990B 2025-03-06T10:55:55+00:00 Johan Hovold johan@kernel.org 2025-03-06T10:44:41+00:00 9a665fe3d967fe46edb4fd2497c7a5cc2dac2f55 The device id entries for Telit FN990B ended up matching only on the interface protocol. While this works, the protocol is qualified by the interface class (and subclass) which should have been included. Switch to matching using USB_DEVICE_AND_INTERFACE_INFO() while keeping the entries sorted also by protocol for consistency. Link: https://lore.kernel.org/20250227110655.3647028-2-fabio.porcedda@gmail.com/ Cc: Fabio Porcedda <fabio.porcedda@gmail.com> Cc: Daniele Palmas <dnlplm@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> 
The device id entries for Telit FN990B ended up matching only on the
interface protocol. While this works, the protocol is qualified by the
interface class (and subclass) which should have been included.

Switch to matching using USB_DEVICE_AND_INTERFACE_INFO() while keeping
the entries sorted also by protocol for consistency.

Link: https://lore.kernel.org/20250227110655.3647028-2-fabio.porcedda@gmail.com/
Cc: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Daniele Palmas <dnlplm@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
USB: serial: option: drop MeiG Smart defines 2025-02-11T16:08:58+00:00 Johan Hovold johan@kernel.org 2025-02-11T14:45:16+00:00 6aa8a63c471eb6756aabd03f880feffe6a7af6c9 Several MeiG Smart modems apparently use the same product id, making the defines even less useful. Drop them in favour of using comments consistently to make the id table slightly less unwieldy. Cc: stable@vger.kernel.org Acked-by: Chester A. Unal <chester.a.unal@arinc9.com> Signed-off-by: Johan Hovold <johan@kernel.org> 
Several MeiG Smart modems apparently use the same product id, making the
defines even less useful.

Drop them in favour of using comments consistently to make the id table
slightly less unwieldy.

Cc: stable@vger.kernel.org
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
USB: serial: option: fix Telit Cinterion FN990A name 2025-02-11T15:01:51+00:00 Fabio Porcedda fabio.porcedda@gmail.com 2025-02-05T17:16:47+00:00 12606fe73f33647c5e79bf666833bf0b225e649d The correct name for FN990 is FN990A so use it in order to avoid confusion with FN990B. Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> 
The correct name for FN990 is FN990A so use it in order to avoid
confusion with FN990B.

Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>