In patch "5d3c28b usb: otg: add device tree support to otg library"
devm_usb_get_phy_by_phandle() was added. It uses try_module_get() to lock the
phy driver in memory. The corresponding module_put() is missing in that patch.

This patch adds try_module_get() to usb_get_phy() and usb_get_phy_dev().
Further the missing module_put() is added to usb_put_phy().

Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Pull USB patches from Greg Kroah-Hartman:
 "Here's the big USB merge for 3.9-rc1

  Nothing major, lots of gadget fixes, and of course, xhci stuff.

  All of this has been in linux-next for a while, with the exception of
  the last 3 patches, which were reverts of patches in the tree that
  caused problems, they went in yesterday."

* tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (190 commits)
  Revert "USB: EHCI: make ehci-vt8500 a separate driver"
  Revert "USB: EHCI: make ehci-orion a separate driver"
  Revert "USB: update host controller Kconfig entries"
  USB: update host controller Kconfig entries
  USB: EHCI: make ehci-orion a separate driver
  USB: EHCI: make ehci-vt8500 a separate driver
  USB: usb-storage: unusual_devs update for Super TOP SATA bridge
  USB: ehci-omap: Fix autoloading of module
  USB: ehci-omap: Don't free gpios that we didn't request
  USB: option: add Huawei "ACM" devices using protocol = vendor
  USB: serial: fix null-pointer dereferences on disconnect
  USB: option: add Yota / Megafon M100-1 4g modem
  drivers/usb: add missing GENERIC_HARDIRQS dependencies
  USB: storage: properly handle the endian issues of idProduct
  testusb: remove all mentions of 'usbfs'
  usb: gadget: imx_udc: make it depend on BROKEN
  usb: omap_control_usb: fix compile warning
  ARM: OMAP: USB: Add phy binding information
  ARM: OMAP2: MUSB: Specify omap4 has mailbox
  ARM: OMAP: devices: create device for usb part of control module
  ...

Felipe writes:
	usb: xceiv: patches for v3.9 merge window

	Two new PHY drivers coming here: one for Samsung,
	one for OMAP. Both architectures are adding USB3
	support to mainline kernel.

	The PHY layer now allows us to have mulitple PHYs
	of the same type, which is necessary for platforms
	which provide more than one USB peripheral port.

	There's also a few cleanups here: removal of __dev*
	annotations, conversion of a cast to to_delayed_work(),
	and mxs-phy learns about ->set_suspend.

Felipe writes:
	usb: gadget: patches for v3.9 merge window

	finally getting rid of the old ->start()/->stop() methods
	in favor of the better and improved ->udc_start()/->udc_stop().

	There were surprisingly quite a few users left, but all of them
	have been converted.

	f_mass_storage removed some dead code, which is always great ;-)

	There's also a big cleanup to the gadget framework from Sebastian
	which gets us a lot closer to having only function drivers in
	kernel and move over to configfs-based binding.

	Other than these, there's the usual set of cleanups: s3c UDCs are
	moving over to devm_regulator_bulk_get() API, at91_udc removed
	an unnecessary check for work_pending() before scheduling and
	there's the removal of an unused variable from uac2_pcm_trigger().

New PHY lib APIs like usb_add_phy_dev() and devm_usb_get_phy_dev() are
used in MUSB (OMAP), in order to make use of the binding information
provided in the board file (of OMAP platforms).

All the platforms should be modified similar to this to add and get the
PHY.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Added an API devm_usb_get_phy_by_phandle(), to get usb phy by passing a
device node phandle value. This function will return a pointer to
the phy on success, -EPROBE_DEFER if there is a device_node for the phandle,
but the phy has not been added, or a ERR_PTR() otherwise.

Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In order to add support for multipe PHY's of the same type, new API's
for adding PHY and getting PHY has been added. Now the binding
information for the PHY and controller should be done in platform file
using usb_bind_phy API. And for getting a PHY, the device pointer of the
USB controller and an index should be passed. Based on the binding
information that is added in the platform file, usb_get_phy_dev will return the
appropriate PHY.
Already existing API's to add and get phy by type is not removed. These
API's are deprecated and will be removed once all the platforms start to
use the new API.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In order to support platforms which has multiple PHY's (of same type) and
which has multiple USB controllers, a new design is adopted wherin the binding
information (between the PHY and the USB controller) should be passed to the
PHY library from platform specific file (board file).
So added a new API to pass the binding information.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

use devm_xxx for otg driver probe. So we do need care about
the resources release in driver remove or failure handling
in driver probe.

Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>