linux-stable.git/drivers/usb/host, branch v5.4.147

usb: ehci-orion: Handle errors of clk_prepare_enable() in probe

2021-09-15T07:47:36+00:00

[ Upstream commit 4720f1bf4ee4a784d9ece05420ba33c9222a3004 ]

ehci_orion_drv_probe() did not account for possible errors of
clk_prepare_enable() that in particular could cause invocation of
clk_disable_unprepare() on clocks that were not prepared/enabled yet,
e.g. in remove or on handling errors of usb_add_hcd() in probe. Though,
there were several patches fixing different issues with clocks in this
driver, they did not solve this problem.

Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe()
to avoid calls of clk_disable_unprepare() without previous successful
invocation of clk_prepare_enable().

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 8c869edaee07 ("ARM: Orion: EHCI: Add support for enabling clocks")
Co-developed-by: Kirill Shilimanov 
Reviewed-by: Andrew Lunn 
Acked-by: Alan Stern 
Signed-off-by: Evgeny Novikov 
Signed-off-by: Kirill Shilimanov 
Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: host: ohci-tmio: add IRQ check

2021-09-15T07:47:35+00:00

[ Upstream commit 4ac5132e8a4300637a2da8f5d6bc7650db735b8a ]

The driver neglects to check the  result of platform_get_irq()'s call and
blithely passes the negative error codes to usb_add_hcd() (which takes
*unsigned* IRQ #), causing request_irq() that it calls to fail with
-EINVAL, overriding an original error code. Stop calling usb_add_hcd()
with the invalid IRQ #s.

Fixes: 78c73414f4f6 ("USB: ohci: add support for tmio-ohci cell")
Acked-by: Alan Stern 
Signed-off-by: Sergey Shtylyov 
Link: https://lore.kernel.org/r/402e1a45-a0a4-0e08-566a-7ca1331506b1@omp.ru
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

xhci: fix unsafe memory usage in xhci tracing

2021-09-12T06:56:41+00:00

commit cbf286e8ef8337308c259ff5b9ce2e74d403be5a upstream.

Removes static char buffer usage in the following decode functions:
	xhci_decode_trb()
	xhci_decode_ptortsc()

Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.

Minor chanes are needed in xhci debugfs code as these functions are also
used there. Changes include moving XHCI_MSG_MAX definititon from
xhci-trace.h to xhci.h

Cc: 
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20210820123503.2605901-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

usb: host: xhci-rcar: Don't reload firmware after the completion

2021-09-12T06:56:41+00:00

commit 57f3ffdc11143f56f1314972fe86fe17a0dcde85 upstream.

According to the datasheet, "Upon the completion of FW Download,
there is no need to write or reload FW.". Otherwise, it's possible
to cause unexpected behaviors. So, adds such a condition.

Fixes: 4ac8918f3a73 ("usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers")
Cc: stable@vger.kernel.org # v3.17+
Signed-off-by: Yoshihiro Shimoda 
Link: https://lore.kernel.org/r/20210827063227.81990-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman

USB:ehci:fix Kunpeng920 ehci hardware problem

2021-08-15T11:08:04+00:00

commit 26b75952ca0b8b4b3050adb9582c8e2f44d49687 upstream.

Kunpeng920's EHCI controller does not have SBRN register.
Reading the SBRN register when the controller driver is
initialized will get 0.

When rebooting the EHCI driver, ehci_shutdown() will be called.
if the sbrn flag is 0, ehci_shutdown() will return directly.
The sbrn flag being 0 will cause the EHCI interrupt signal to
not be turned off after reboot. this interrupt that is not closed
will cause an exception to the device sharing the interrupt.

Therefore, the EHCI controller of Kunpeng920 needs to skip
the read operation of the SBRN register.

Acked-by: Alan Stern 
Signed-off-by: Longfang Liu 
Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman

xhci: add xhci_get_virt_ep() helper

2021-07-28T11:31:02+00:00

[commit b1adc42d440df3233255e313a45ab7e9b2b74096 upstream]

In several event handlers we need to find the right endpoint
structure from slot_id and ep_index in the event.

Add a helper for this, check that slot_id and ep_index are valid.

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20210129130044.206855-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Carsten Schmid 
Signed-off-by: Greg Kroah-Hartman

usb: max-3421: Prevent corruption of freed memory

2021-07-28T11:30:59+00:00

commit b5fdf5c6e6bee35837e160c00ac89327bdad031b upstream.

The MAX-3421 USB driver remembers the state of the USB toggles for a
device/endpoint. To save SPI writes, this was only done when a new
device/endpoint was being used. Unfortunately, if the old device was
removed, this would cause writes to freed memory.

To fix this, a simpler scheme is used. The toggles are read from
hardware when a URB is completed, and the toggles are always written to
hardware when any URB transaction is started. This will cause a few more
SPI transactions, but no causes kernel panics.

Fixes: 2d53139f3162 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable 
Signed-off-by: Mark Tomlinson 
Link: https://lore.kernel.org/r/20210625031456.8632-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman

xhci: Fix lost USB 2 remote wake

2021-07-28T11:30:59+00:00

commit 72f68bf5c756f5ce1139b31daae2684501383ad5 upstream.

There's a small window where a USB 2 remote wake may be left unhandled
due to a race between hub thread and xhci port event interrupt handler.

When the resume event is detected in the xhci interrupt handler it kicks
the hub timer, which should move the port from resume to U0 once resume
has been signalled for long enough.

To keep the hub "thread" running we set a bus_state->resuming_ports flag.
This flag makes sure hub timer function kicks itself.

checking this flag was not properly protected by the spinlock. Flag was
copied to a local variable before lock was taken. The local variable was
then checked later with spinlock held.

If interrupt is handled right after copying the flag to the local variable
we end up stopping the hub thread before it can handle the USB 2 resume.

CPU0					CPU1
(hub thread)				(xhci event handler)

xhci_hub_status_data()
status = bus_state->resuming_ports;
					
					handle_port_status()
					spin_lock()
					bus_state->resuming_ports = 1
					set_flag(HCD_FLAG_POLL_RH)
					spin_unlock()
spin_lock()
if (!status)
  clear_flag(HCD_FLAG_POLL_RH)
spin_unlock()

Fix this by taking the lock a bit earlier so that it covers
the resuming_ports flag copy in the hub thread

Cc: 
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20210715150651.1996099-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

xhci: solve a double free problem while doing s4

2021-07-14T14:53:01+00:00

commit b31d9d6d7abbf6483b871b6370bc31c930d53f54 upstream.

when system is doing s4, the process of xhci_resume may be as below:
1、xhci_mem_cleanup
2、xhci_init->xhci_mem_init->xhci_mem_cleanup(when memory is not enough).
xhci_mem_cleanup will be executed twice when system is out of memory.
xhci->port_caps is freed in xhci_mem_cleanup,but it isn't set to NULL.
It will be freed twice when xhci_mem_cleanup is called the second time.

We got following bug when system resumes from s4:

kernel BUG at mm/slub.c:309!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
CPU: 0 PID: 5929 Tainted: G S   W   5.4.96-arm64-desktop #1
pc : __slab_free+0x5c/0x424
lr : kfree+0x30c/0x32c

Call trace:
 __slab_free+0x5c/0x424
 kfree+0x30c/0x32c
 xhci_mem_cleanup+0x394/0x3cc
 xhci_mem_init+0x9ac/0x1070
 xhci_init+0x8c/0x1d0
 xhci_resume+0x1cc/0x5fc
 xhci_plat_resume+0x64/0x70
 platform_pm_thaw+0x28/0x60
 dpm_run_callback+0x54/0x24c
 device_resume+0xd0/0x200
 async_resume+0x24/0x60
 async_run_entry_fn+0x44/0x110
 process_one_work+0x1f0/0x490
 worker_thread+0x5c/0x450
 kthread+0x158/0x160
 ret_from_fork+0x10/0x24

Original patch that caused this issue was backported to 4.4 stable,
so this should be backported to 4.4 stabe as well.

Fixes: cf0ee7c60c89 ("xhci: Fix memory leak when caching protocol extended capability PSI tables - take 2")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Jiantao Zhang 
Signed-off-by: Tao Xue 
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20210617150354.1512157-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

usb: sl811-hcd: improve misleading indentation

2021-05-22T09:38:27+00:00

commit 8460f6003a1d2633737b89c4f69d6f4c0c7c65a3 upstream.

gcc-11 now warns about a confusingly indented code block:

drivers/usb/host/sl811-hcd.c: In function ‘sl811h_hub_control’:
drivers/usb/host/sl811-hcd.c:1291:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
 1291 |         if (*(u16*)(buf+2))     /* only if wPortChange is interesting */
      |         ^~
drivers/usb/host/sl811-hcd.c:1295:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
 1295 |                 break;

Rewrite this to use a single if() block with the __is_defined() macro.

Signed-off-by: Arnd Bergmann 
Link: https://lore.kernel.org/r/20210322164244.827589-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman