linux-stable.git/drivers/usb/host, branch v4.4.286

Revert "USB: xhci: fix U1/U2 handling for hardware with XHCI_INTEL_HOST quirk set"

2021-09-22T09:41:26+00:00

[ Upstream commit 2847c46c61486fd8bca9136a6e27177212e78c69 ]

This reverts commit 5d5323a6f3625f101dbfa94ba3ef7706cce38760.

That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.

Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2

After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.

Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.

exit latency calculations have been revised since then

Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: host: fotg210: fix the actual_length of an iso packet

2021-09-22T09:41:24+00:00

[ Upstream commit 091cb2f782f32ab68c6f5f326d7868683d3d4875 ]

We should acquire the actual_length of an iso packet
from the iTD directly using FOTG210_ITD_LENGTH() macro.

Signed-off-by: Kelly Devilliv 
Link: https://lore.kernel.org/r/20210627125747.127646-4-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: ehci-orion: Handle errors of clk_prepare_enable() in probe

2021-09-22T09:41:22+00:00

[ Upstream commit 4720f1bf4ee4a784d9ece05420ba33c9222a3004 ]

ehci_orion_drv_probe() did not account for possible errors of
clk_prepare_enable() that in particular could cause invocation of
clk_disable_unprepare() on clocks that were not prepared/enabled yet,
e.g. in remove or on handling errors of usb_add_hcd() in probe. Though,
there were several patches fixing different issues with clocks in this
driver, they did not solve this problem.

Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe()
to avoid calls of clk_disable_unprepare() without previous successful
invocation of clk_prepare_enable().

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 8c869edaee07 ("ARM: Orion: EHCI: Add support for enabling clocks")
Co-developed-by: Kirill Shilimanov 
Reviewed-by: Andrew Lunn 
Acked-by: Alan Stern 
Signed-off-by: Evgeny Novikov 
Signed-off-by: Kirill Shilimanov 
Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: host: ohci-tmio: add IRQ check

2021-09-22T09:41:21+00:00

[ Upstream commit 4ac5132e8a4300637a2da8f5d6bc7650db735b8a ]

The driver neglects to check the  result of platform_get_irq()'s call and
blithely passes the negative error codes to usb_add_hcd() (which takes
*unsigned* IRQ #), causing request_irq() that it calls to fail with
-EINVAL, overriding an original error code. Stop calling usb_add_hcd()
with the invalid IRQ #s.

Fixes: 78c73414f4f6 ("USB: ohci: add support for tmio-ohci cell")
Acked-by: Alan Stern 
Signed-off-by: Sergey Shtylyov 
Link: https://lore.kernel.org/r/402e1a45-a0a4-0e08-566a-7ca1331506b1@omp.ru
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB:ehci:fix Kunpeng920 ehci hardware problem

2021-08-15T10:59:56+00:00

commit 26b75952ca0b8b4b3050adb9582c8e2f44d49687 upstream.

Kunpeng920's EHCI controller does not have SBRN register.
Reading the SBRN register when the controller driver is
initialized will get 0.

When rebooting the EHCI driver, ehci_shutdown() will be called.
if the sbrn flag is 0, ehci_shutdown() will return directly.
The sbrn flag being 0 will cause the EHCI interrupt signal to
not be turned off after reboot. this interrupt that is not closed
will cause an exception to the device sharing the interrupt.

Therefore, the EHCI controller of Kunpeng920 needs to skip
the read operation of the SBRN register.

Acked-by: Alan Stern 
Signed-off-by: Longfang Liu 
Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman

usb: max-3421: Prevent corruption of freed memory

2021-07-28T07:12:36+00:00

commit b5fdf5c6e6bee35837e160c00ac89327bdad031b upstream.

The MAX-3421 USB driver remembers the state of the USB toggles for a
device/endpoint. To save SPI writes, this was only done when a new
device/endpoint was being used. Unfortunately, if the old device was
removed, this would cause writes to freed memory.

To fix this, a simpler scheme is used. The toggles are read from
hardware when a URB is completed, and the toggles are always written to
hardware when any URB transaction is started. This will cause a few more
SPI transactions, but no causes kernel panics.

Fixes: 2d53139f3162 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable 
Signed-off-by: Mark Tomlinson 
Link: https://lore.kernel.org/r/20210625031456.8632-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman

xhci: Fix lost USB 2 remote wake

2021-07-28T07:12:36+00:00

commit 72f68bf5c756f5ce1139b31daae2684501383ad5 upstream.

There's a small window where a USB 2 remote wake may be left unhandled
due to a race between hub thread and xhci port event interrupt handler.

When the resume event is detected in the xhci interrupt handler it kicks
the hub timer, which should move the port from resume to U0 once resume
has been signalled for long enough.

To keep the hub "thread" running we set a bus_state->resuming_ports flag.
This flag makes sure hub timer function kicks itself.

checking this flag was not properly protected by the spinlock. Flag was
copied to a local variable before lock was taken. The local variable was
then checked later with spinlock held.

If interrupt is handled right after copying the flag to the local variable
we end up stopping the hub thread before it can handle the USB 2 resume.

CPU0					CPU1
(hub thread)				(xhci event handler)

xhci_hub_status_data()
status = bus_state->resuming_ports;
					
					handle_port_status()
					spin_lock()
					bus_state->resuming_ports = 1
					set_flag(HCD_FLAG_POLL_RH)
					spin_unlock()
spin_lock()
if (!status)
  clear_flag(HCD_FLAG_POLL_RH)
spin_unlock()

Fix this by taking the lock a bit earlier so that it covers
the resuming_ports flag copy in the hub thread

Cc: 
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20210715150651.1996099-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

xhci: Do not use GFP_KERNEL in (potentially) atomic context

2021-05-22T08:38:30+00:00

commit dda32c00c9a0fa103b5d54ef72c477b7aa993679 upstream.

'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')

So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.

Be safe and pass the mem_flags to this function as well.

Fixes: ddba5cd0aeff ("xhci: Use command structures when queuing commands on the command ring")
Cc: 
Signed-off-by: Christophe JAILLET 
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com
[iwamatsu: Adjust context]
Signed-off-by: Nobuhiro Iwamatsu 
Signed-off-by: Greg Kroah-Hartman

usb: sl811-hcd: improve misleading indentation

2021-05-22T08:38:29+00:00

commit 8460f6003a1d2633737b89c4f69d6f4c0c7c65a3 upstream.

gcc-11 now warns about a confusingly indented code block:

drivers/usb/host/sl811-hcd.c: In function ‘sl811h_hub_control’:
drivers/usb/host/sl811-hcd.c:1291:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
 1291 |         if (*(u16*)(buf+2))     /* only if wPortChange is interesting */
      |         ^~
drivers/usb/host/sl811-hcd.c:1295:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
 1295 |                 break;

Rewrite this to use a single if() block with the __is_defined() macro.

Signed-off-by: Arnd Bergmann 
Link: https://lore.kernel.org/r/20210322164244.827589-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman

usb: xhci: Increase timeout for HC halt

2021-05-22T08:38:29+00:00

commit ca09b1bea63ab83f4cca3a2ae8bc4f597ec28851 upstream.

On some devices (specifically the SC8180x based Surface Pro X with
QCOM04A6) HC halt / xhci_halt() times out during boot. Manually binding
the xhci-hcd driver at some point later does not exhibit this behavior.
To work around this, double XHCI_MAX_HALT_USEC, which also resolves this
issue.

Cc: 
Signed-off-by: Maximilian Luz 
Signed-off-by: Mathias Nyman 
Link: https://lore.kernel.org/r/20210512080816.866037-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman