linux-stable.git/drivers/usb/host, branch v4.4.26

xhci: fix null pointer dereference in stop command timeout function

2016-09-24T08:07:41+00:00

commit bcf42aa60c2832510b9be0f30c090bfd35bb172d upstream.

The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)

the ->primary_hcd will be set to NULL at USB3 hcd removal.

Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

xhci: Make sure xhci handles USB_SPEED_SUPER_PLUS devices.

2016-09-07T06:32:40+00:00

commit 0caf6b33452112e5a1186c8c964e90310e49e6bd upstream.

In most cases the devices with the speed set to USB_SPEED_SUPER_PLUS
are handled like regular SuperSpeed devices.

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

xhci: don't dereference a xhci member after removing xhci

2016-09-07T06:32:40+00:00

commit f1f6d9a8b540df22b87a5bf6bc104edaade81f47 upstream.

Remove the hcd after checking for the xhci last quirks, not before.

This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb: xhci: Fix panic if disconnect

2016-09-07T06:32:40+00:00

commit 88716a93766b8f095cdef37a8e8f2c93aa233b21 upstream.

After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device

If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.

virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)

[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G     U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4

This issue is found when running with realtek ethernet device
(0bda:8153).

Signed-off-by: Jim Lin 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

xhci: always handle "Command Ring Stopped" events

2016-09-07T06:32:40+00:00

commit 33be126510974e2eb9679f1ca9bca4f67ee4c4c7 upstream.

Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.

The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.

Solve it by handling the command ring stopped event before checking for a
matching command.

In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.

If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb: ehci: change order of register cleanup during shutdown

2016-09-07T06:32:38+00:00

commit bc337b51508beb2d039aff5074a76cfe1c212030 upstream.

In ehci_turn_off_all_ports() all EHCI port registers are cleared to zero.
On some hardware, this can lead to an system hang,
when ehci_port_power() accesses the already cleared registers.

This patch changes the order of cleanup.
First call ehci_port_power() which respects the current bits in
port status registers
and afterwards cleanup the hard way by setting everything to zero.

Signed-off-by: Marc Ohlf 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: OHCI: Don't mark EDs as ED_OPER if scheduling fails

2016-08-10T09:49:24+00:00

commit c66f59ee5050447b3da92d36f5385a847990a894 upstream.

Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.

This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.

The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.

Fix ed_schedule to update ED state only on successful return.

Signed-off-by: Michal Pecio 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

usb: host: ehci-tegra: Grab the correct UTMI pads reset

2016-07-11T16:31:13+00:00

commit f8a15a9650694feaa0dabf197b0c94d37cd3fb42 upstream.

There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.

Commit a47cc24cd1e5 ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.

This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.

Fixes: a47cc24cd1e5 ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: Jon Hunter 
Signed-off-by: Thierry Reding 
Signed-off-by: Greg Kroah-Hartman

xhci: Fix handling timeouted commands on hosts in weird states.

2016-07-11T16:31:13+00:00

commit 3425aa03f484d45dc21e0e791c2f6c74ea656421 upstream.

If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.

If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.

There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.

The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.

Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.

Tested-by: Joe Lawrence 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

USB: xhci: Add broken streams quirk for Frescologic device id 1009

2016-07-11T16:31:13+00:00

commit d95815ba6a0f287213118c136e64d8c56daeaeab upstream.

I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.

Tests on another motherboard show that it does work with streams disabled.

Signed-off-by: Hans de Goede 
Signed-off-by: Greg Kroah-Hartman