linux-stable.git/drivers/usb/host, branch v4.19.7 Linux kernel stable tree usb: xhci: Prevent bus suspend if a port connect change or polling state is detected 2018-12-01T08:37:25+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2018-11-15T09:38:41+00:00 cc8b329fef53c74a4abf98b0755b3832d572d6ce commit 2f31a67f01a8beb22cae754c53522cb61a005750 upstream. USB3 roothub might autosuspend before a plugged USB3 device is detected, causing USB3 device enumeration failure. USB3 devices don't show up as connected and enabled until USB3 link trainig completes. On a fast booting platform with a slow USB3 link training the link might reach the connected enabled state just as the bus is suspending. If this device is discovered first time by the xhci_bus_suspend() routine it will be put to U3 suspended state like the other ports which failed to suspend earlier. The hub thread will notice the connect change and resume the bus, moving the port back to U0 This U0 -> U3 -> U0 transition right after being connected seems to be too much for some devices, causing them to first go to SS.Inactive state, and finally end up stuck in a polling state with reset asserted Fix this by failing the bus suspend if a port has a connect change or is in a polling state in xhci_bus_suspend(). Don't do any port changes until all ports are checked, buffer all port changes and only write them in the end if suspend can proceed Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2f31a67f01a8beb22cae754c53522cb61a005750 upstream.

USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.

USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.

If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.

The hub thread will notice the connect change and resume the bus,
moving the port back to U0

This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted

Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().

Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Add quirk to workaround the errata seen on Cavium Thunder-X2 Soc 2018-12-01T08:37:25+00:00 Cherian, George George.Cherian@cavium.com 2018-11-09T15:21:22+00:00 b6cc7f9c6461a3d23bc1e8ad47eacb0a2188168a commit 11644a7659529730eaf2f166efaabe7c3dc7af8c upstream. Implement workaround for ThunderX2 Errata-129 (documented in CN99XX Known Issues" available at Cavium support site). As per ThunderX2errata-129, USB 2 device may come up as USB 1 if a connection to a USB 1 device is followed by another connection to a USB 2 device, the link will come up as USB 1 for the USB 2 device. Resolution: Reset the PHY after the USB 1 device is disconnected. The PHY reset sequence is done using private registers in XHCI register space. After the PHY is reset we check for the PLL lock status and retry the operation if it fails. From our tests, retrying 4 times is sufficient. Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround in handle_xhci_port_status(). Cc: stable@vger.kernel.org Signed-off-by: George Cherian <george.cherian@cavium.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 11644a7659529730eaf2f166efaabe7c3dc7af8c upstream.

Implement workaround for ThunderX2 Errata-129 (documented in
CN99XX Known Issues" available at Cavium support site).
As per ThunderX2errata-129, USB 2 device may come up as USB 1
if a connection to a USB 1 device is followed by another connection to
a USB 2 device, the link will come up as USB 1 for the USB 2 device.

Resolution: Reset the PHY after the USB 1 device is disconnected.
The PHY reset sequence is done using private registers in XHCI register
space. After the PHY is reset we check for the PLL lock status and retry
the operation if it fails. From our tests, retrying 4 times is sufficient.

Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround
in handle_xhci_port_status().

Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: xhci: fix timeout for transition from RExit to U0 2018-12-01T08:37:25+00:00 Aaron Ma aaron.ma@canonical.com 2018-11-09T15:21:21+00:00 cad3876cd23d63e818c3112e885767a09b249905 commit a5baeaeabcca3244782a9b6382ebab6f8a58f583 upstream. This definition is used by msecs_to_jiffies in milliseconds. According to the comments, max rexit timeout should be 20ms. Align with the comments to properly calculate the delay. Verified on Sunrise Point-LP and Cannon Lake. Cc: stable@vger.kernel.org Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a5baeaeabcca3244782a9b6382ebab6f8a58f583 upstream.

This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.

Verified on Sunrise Point-LP and Cannon Lake.

Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: xhci: fix uninitialized completion when USB3 port got wrong status 2018-12-01T08:37:25+00:00 Aaron Ma aaron.ma@canonical.com 2018-11-09T15:21:20+00:00 60ac01c60ba94d8a17016ede99789207a5b93856 commit 958c0bd86075d4ef1c936998deefe1947e539240 upstream. Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3, after clear port reset it works fine. Since this device is registered on USB3 roothub at boot, when port status reports not superspeed, xhci_get_port_status will call an uninitialized completion in bus_state[0]. Kernel will hang because of NULL pointer. Restrict the USB2 resume status check in USB2 roothub to fix hang issue. Cc: stable@vger.kernel.org Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 958c0bd86075d4ef1c936998deefe1947e539240 upstream.

Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.

Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.

Restrict the USB2 resume status check in USB2 roothub to fix hang issue.

Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Add check for invalid byte size error when UAS devices are connected. 2018-12-01T08:37:25+00:00 Sandeep Singh sandeep.singh@amd.com 2018-11-09T15:21:19+00:00 3e8886bd158fc34efad491176b8899417736dc1f commit d9193efba84fe4c4aa22a569fade5e6ca971f8af upstream. Observed "TRB completion code (27)" error which corresponds to Stopped - Length Invalid error(xhci spec section 4.17.4) while connecting USB to SATA bridge. Looks like this case was not considered when the following patch[1] was committed. Hence adding this new check which can prevent the invalid byte size error. [1] ade2e3a xhci: handle transfer events without TRB pointer Cc: <stable@vger.kernel.org> Signed-off-by: Sandeep Singh <sandeep.singh@amd.com> cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit d9193efba84fe4c4aa22a569fade5e6ca971f8af upstream.

Observed "TRB completion code (27)" error which corresponds to Stopped -
Length Invalid error(xhci spec section 4.17.4) while connecting USB to
SATA bridge.

Looks like this case was not considered when the following patch[1] was
committed. Hence adding this new check which can prevent
the invalid byte size error.

[1] ade2e3a xhci: handle transfer events without TRB pointer

Cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: handle port status events for removed USB3 hcd 2018-12-01T08:37:25+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2018-11-09T15:21:18+00:00 a237717dfdbc5e6f7cd9d5b2d66627ad793bb8cf commit 1245374e9b8340fc255fd51b2015173a83050d03 upstream. At xhci removal the USB3 hcd (shared_hcd) is removed before the primary USB2 hcd. Interrupts for port status changes may still occur for USB3 ports after the shared_hcd is freed, causing NULL pointer dereference. Check if xhci->shared_hcd is still valid before handing USB3 port events Cc: <stable@vger.kernel.org> Reported-by: Peter Chen <peter.chen@nxp.com> Tested-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 1245374e9b8340fc255fd51b2015173a83050d03 upstream.

At xhci removal the USB3 hcd (shared_hcd) is removed before the primary
USB2 hcd. Interrupts for port status changes may still occur for USB3
ports after the shared_hcd is freed, causing  NULL pointer dereference.

Check if xhci->shared_hcd is still valid before handing USB3 port events

Cc: <stable@vger.kernel.org>
Reported-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Fix leaking USB3 shared_hcd at xhci removal 2018-12-01T08:37:25+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2018-11-09T15:21:17+00:00 82c1b66894fd3b81af823861a39d532af4337f4e commit f068090426ea8d72c408ebd42953a82a88e2282c upstream. Ensure that the shared_hcd pointer is valid when calling usb_put_hcd() The shared_hcd is removed and freed in xhci by first calling usb_remove_hcd(xhci->shared_hcd), and later usb_put_hcd(xhci->shared_hcd) Afer commit fe190ed0d602 ("xhci: Do not halt the host until both HCD have disconnected their devices.") the shared_hcd was never properly put as xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was called. shared_hcd (USB3) is removed before primary hcd (USB2). While removing the primary hcd we might need to handle xhci interrupts to cleanly remove last USB2 devices, therefore we need to set xhci->shared_hcd to NULL before removing the primary hcd to let xhci interrupt handler know shared_hcd is no longer available. xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before adding them. so to keep the correct reverse removal order use a temporary shared_hcd variable for them. For more details see commit 4ac53087d6d4 ("usb: xhci: plat: Create both HCDs before adding them") Fixes: fe190ed0d602 ("xhci: Do not halt the host until both HCD have disconnected their devices.") Cc: Joel Stanley <joel@jms.id.au> Cc: Chunfeng Yun <chunfeng.yun@mediatek.com> Cc: Thierry Reding <treding@nvidia.com> Cc: Jianguo Sun <sunjianguo1@huawei.com> Cc: <stable@vger.kernel.org> Reported-by: Jack Pham <jackp@codeaurora.org> Tested-by: Jack Pham <jackp@codeaurora.org> Tested-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit f068090426ea8d72c408ebd42953a82a88e2282c upstream.

Ensure that the shared_hcd pointer is valid when calling usb_put_hcd()

The shared_hcd is removed and freed in xhci by first calling
usb_remove_hcd(xhci->shared_hcd), and later
usb_put_hcd(xhci->shared_hcd)

Afer commit fe190ed0d602 ("xhci: Do not halt the host until both HCD have
disconnected their devices.") the shared_hcd was never properly put as
xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was
called.

shared_hcd (USB3) is removed before primary hcd (USB2).
While removing the primary hcd we might need to handle xhci interrupts
to cleanly remove last USB2 devices, therefore we need to set
xhci->shared_hcd to NULL before removing the primary hcd to let xhci
interrupt handler know shared_hcd is no longer available.

xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before
adding them. so to keep the correct reverse removal order use a temporary
shared_hcd variable for them.
For more details see commit 4ac53087d6d4 ("usb: xhci: plat: Create both
HCDs before adding them")

Fixes: fe190ed0d602 ("xhci: Do not halt the host until both HCD have disconnected their devices.")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Avoid USB autosuspend when resuming USB2 ports. 2018-11-13T19:08:35+00:00 Anshuman Gupta anshuman.gupta@intel.com 2018-09-20T16:13:40+00:00 974c4312604d8758c3fc71ad0cc445ddd99ff5d3 [ Upstream commit 330e2d61cdd58363eb5e66b2e72f76fe3c5492e0 ] When USB bus host controller root hub resumes from autosuspend, it immediately tries to enter auto-suspend, but there can be a scenario when root hub is resuming its usb2 ports, in that particular case USB host controller auto suspend fails since it is busy to resuming its usb2 ports. This makes multiple failed cycles of auto-suspend until all usb2 ports of host controller root hub do not resume. This patch uses USB core framework usb_hcd_start_port_resume, usb_hcd_end_port_resume API's in order to autoresume/autosuspend root hub properly. Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit 330e2d61cdd58363eb5e66b2e72f76fe3c5492e0 ]

When USB bus host controller root hub resumes from autosuspend,
it immediately tries to enter auto-suspend, but there can be a
scenario when root hub is resuming its usb2 ports, in that particular
case USB host controller auto suspend fails since it is busy
to resuming its usb2 ports.

This makes multiple failed cycles of auto-suspend until all usb2
ports of host controller root hub do not resume.

This patch uses USB core framework usb_hcd_start_port_resume,
usb_hcd_end_port_resume API's in order to  autoresume/autosuspend
root hub properly.

Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: host: ohci-at91: fix request of irq for optional gpio 2018-11-13T19:08:33+00:00 Tudor.Ambarus@microchip.com Tudor.Ambarus@microchip.com 2018-10-15T09:00:54+00:00 49c8a09eaa234494a456f1da6770eac7b5feae2c [ Upstream commit 325b9313ec3be56c8e2fe03f977fee19cec75820 ] atmel,oc-gpio is optional. Request its irq only when atmel,oc is set in device tree. devm_gpiod_get_index_optional returns NULL if -ENOENT. Check its return value for NULL before error, because it is more probable that atmel,oc is not set. This fixes the following errors on boards where atmel,oc is not set in device tree: [ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ [ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ [ 0.970000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
[ Upstream commit 325b9313ec3be56c8e2fe03f977fee19cec75820 ]

atmel,oc-gpio is optional. Request its irq only when atmel,oc is set
in device tree.

devm_gpiod_get_index_optional returns NULL if -ENOENT. Check its
return value for NULL before error, because it is more probable that
atmel,oc is not set.

This fixes the following errors on boards where atmel,oc is not set in
device tree:
[    0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[    0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[    0.970000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: xhci: pci: Enable Intel USB role mux on Apollo Lake platforms 2018-10-09T14:13:50+00:00 Heikki Krogerus heikki.krogerus@linux.intel.com 2018-10-01T15:53:05+00:00 c02588a352defaf985fc1816eb6232663159e1b8 Intel Apollo Lake has the same internal USB role mux as Intel Cherry Trail. Cc: <stable@vger.kernel.org> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Intel Apollo Lake has the same internal USB role mux as
Intel Cherry Trail.

Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>