linux-stable.git/drivers/usb/host, branch v4.14.151 Linux kernel stable tree xhci: Increase STS_SAVE timeout in xhci_suspend() 2019-10-17T20:43:24+00:00 Kai-Heng Feng kai.heng.feng@canonical.com 2019-10-04T11:59:32+00:00 88ec6870dbe4edcf480f555430549f512084d84e commit ac343366846a445bb81f0a0e8f16abb8bd5d5d88 upstream. After commit f7fac17ca925 ("xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()"), ASMedia xHCI may fail to suspend. Although the algorithms are essentially the same, the old max timeout is (usec + usec * time of doing readl()), and the new max timeout is just usec, which is much less than the old one. Increase the timeout to make ASMedia xHCI able to suspend again. BugLink: https://bugs.launchpad.net/bugs/1844021 Fixes: f7fac17ca925 ("xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()") Cc: <stable@vger.kernel.org> # v5.2+ Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-8-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit ac343366846a445bb81f0a0e8f16abb8bd5d5d88 upstream.

After commit f7fac17ca925 ("xhci: Convert xhci_handshake() to use
readl_poll_timeout_atomic()"), ASMedia xHCI may fail to suspend.

Although the algorithms are essentially the same, the old max timeout is
(usec + usec * time of doing readl()), and the new max timeout is just
usec, which is much less than the old one.

Increase the timeout to make ASMedia xHCI able to suspend again.

BugLink: https://bugs.launchpad.net/bugs/1844021
Fixes: f7fac17ca925 ("xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()")
Cc: <stable@vger.kernel.org> # v5.2+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-8-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: xhci: wait for CNR controller not ready bit in xhci resume 2019-10-17T20:43:23+00:00 Rick Tseng rtseng@nvidia.com 2019-10-04T11:59:30+00:00 f4109e2a27705bf27f1da879aa8fe52208452850 commit a70bcbc322837eda1ab5994d12db941dc9733a7d upstream. NVIDIA 3.1 xHCI card would lose power when moving power state into D3Cold. Thus we need to wait for CNR bit to clear in xhci resume, just as in xhci init. [Minor changes to comment and commit message -Mathias] Cc: <stable@vger.kernel.org> Signed-off-by: Rick Tseng <rtseng@nvidia.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-6-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a70bcbc322837eda1ab5994d12db941dc9733a7d upstream.

NVIDIA 3.1 xHCI card would lose power when moving power state into D3Cold.
Thus we need to wait for CNR bit to clear in xhci resume, just as in
xhci init.

[Minor changes to comment and commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Rick Tseng <rtseng@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-6-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Check all endpoints for LPM timeout 2019-10-17T20:43:23+00:00 Jan Schmidt jan@centricular.com 2019-10-04T11:59:28+00:00 7f14f84339f328233e8201e69e98085ed9bc3e12 commit d500c63f80f2ea08ee300e57da5f2af1c13875f5 upstream. If an endpoint is encountered that returns USB3_LPM_DEVICE_INITIATED, keep checking further endpoints, as there might be periodic endpoints later that return USB3_LPM_DISABLED due to shorter service intervals. Without this, the code can set too high a maximum-exit-latency and prevent the use of multiple USB3 cameras that should be able to work. Cc: <stable@vger.kernel.org> Signed-off-by: Jan Schmidt <jan@centricular.com> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-4-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit d500c63f80f2ea08ee300e57da5f2af1c13875f5 upstream.

If an endpoint is encountered that returns USB3_LPM_DEVICE_INITIATED, keep
checking further endpoints, as there might be periodic endpoints later
that return USB3_LPM_DISABLED due to shorter service intervals.

Without this, the code can set too high a maximum-exit-latency and
prevent the use of multiple USB3 cameras that should be able to work.

Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Schmidt <jan@centricular.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Prevent device initiated U1/U2 link pm if exit latency is too long 2019-10-17T20:43:23+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2019-10-04T11:59:27+00:00 81413e70cc464d83fd27dce4ac2bbfadcbd1435d commit cd9d9491e835a845c1a98b8471f88d26285e0bb9 upstream. If host/hub initiated link pm is prevented by a driver flag we still must ensure that periodic endpoints have longer service intervals than link pm exit latency before allowing device initiated link pm. Fix this by continue walking and checking endpoint service interval if xhci_get_timeout_no_hub_lpm() returns anything else than USB3_LPM_DISABLED While at it fix the split line error message Tested-by: Jan Schmidt <jan@centricular.com> Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-3-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit cd9d9491e835a845c1a98b8471f88d26285e0bb9 upstream.

If host/hub initiated link pm is prevented by a driver flag we still must
ensure that periodic endpoints have longer service intervals than link pm
exit latency before allowing device initiated link pm.

Fix this by continue walking and checking endpoint service interval if
xhci_get_timeout_no_hub_lpm() returns anything else than USB3_LPM_DISABLED

While at it fix the split line error message

Tested-by: Jan Schmidt <jan@centricular.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Fix false warning message about wrong bounce buffer write length 2019-10-17T20:43:22+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2019-10-04T11:59:26+00:00 83f8e29a68e8dc0d64c67df2663b59fd19e47148 commit c03101ff4f74bb30679c1a03d551ecbef1024bf6 upstream. The check printing out the "WARN Wrong bounce buffer write length:" uses incorrect values when comparing bytes written from scatterlist to bounce buffer. Actual copied lengths are fine. The used seg->bounce_len will be set to equal new_buf_len a few lines later in the code, but is incorrect when doing the comparison. The patch which added this false warning was backported to 4.8+ kernels so this should be backported as far as well. Cc: <stable@vger.kernel.org> # v4.8+ Fixes: 597c56e372da ("xhci: update bounce buffer with correct sg num") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-2-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c03101ff4f74bb30679c1a03d551ecbef1024bf6 upstream.

The check printing out the "WARN Wrong bounce buffer write length:"
uses incorrect values when comparing bytes written from scatterlist
to bounce buffer. Actual copied lengths are fine.

The used seg->bounce_len will be set to equal new_buf_len a few lines later
in the code, but is incorrect when doing the comparison.

The patch which added this false warning was backported to 4.8+ kernels
so this should be backported as far as well.

Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 597c56e372da ("xhci: update bounce buffer with correct sg num")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: host: xhci: rcar: Fix typo in compatible string matching 2019-09-06T08:20:57+00:00 Geert Uytterhoeven geert+renesas@glider.be 2019-08-27T12:51:12+00:00 6b2f9ecf5d2c0d1aadead91b25bb11b205487772 commit 636bd02a7ba9025ff851d0cfb92768c8fa865859 upstream. It's spelled "renesas", not "renensas". Due to this typo, RZ/G1M and RZ/G1N were not covered by the check. Fixes: 2dc240a3308b ("usb: host: xhci: rcar: retire use of xhci_plat_type_is()") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable <stable@vger.kernel.org> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/20190827125112.12192-1-geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 636bd02a7ba9025ff851d0cfb92768c8fa865859 upstream.

It's spelled "renesas", not "renensas".

Due to this typo, RZ/G1M and RZ/G1N were not covered by the check.

Fixes: 2dc240a3308b ("usb: host: xhci: rcar: retire use of xhci_plat_type_is()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20190827125112.12192-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: host: ohci: fix a race condition between shutdown and irq 2019-09-06T08:20:56+00:00 Yoshihiro Shimoda yoshihiro.shimoda.uh@renesas.com 2019-08-27T03:51:50+00:00 8e7ca9eecdc9e8afd3700e64685d1817234b5b71 commit a349b95d7ca0cea71be4a7dac29830703de7eb62 upstream. This patch fixes an issue that the following error is possible to happen when ohci hardware causes an interruption and the system is shutting down at the same time. [ 34.851754] usb 2-1: USB disconnect, device number 2 [ 35.166658] irq 156: nobody cared (try booting with the "irqpoll" option) [ 35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85 [ 35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) [ 35.187886] Workqueue: usb_hub_wq hub_event [ 35.192063] Call trace: [ 35.194509] dump_backtrace+0x0/0x150 [ 35.198165] show_stack+0x14/0x20 [ 35.201475] dump_stack+0xa0/0xc4 [ 35.204785] __report_bad_irq+0x34/0xe8 [ 35.208614] note_interrupt+0x2cc/0x318 [ 35.212446] handle_irq_event_percpu+0x5c/0x88 [ 35.216883] handle_irq_event+0x48/0x78 [ 35.220712] handle_fasteoi_irq+0xb4/0x188 [ 35.224802] generic_handle_irq+0x24/0x38 [ 35.228804] __handle_domain_irq+0x5c/0xb0 [ 35.232893] gic_handle_irq+0x58/0xa8 [ 35.236548] el1_irq+0xb8/0x180 [ 35.239681] __do_softirq+0x94/0x23c [ 35.243253] irq_exit+0xd0/0xd8 [ 35.246387] __handle_domain_irq+0x60/0xb0 [ 35.250475] gic_handle_irq+0x58/0xa8 [ 35.254130] el1_irq+0xb8/0x180 [ 35.257268] kernfs_find_ns+0x5c/0x120 [ 35.261010] kernfs_find_and_get_ns+0x3c/0x60 [ 35.265361] sysfs_unmerge_group+0x20/0x68 [ 35.269454] dpm_sysfs_remove+0x2c/0x68 [ 35.273284] device_del+0x80/0x370 [ 35.276683] hid_destroy_device+0x28/0x60 [ 35.280686] usbhid_disconnect+0x4c/0x80 [ 35.284602] usb_unbind_interface+0x6c/0x268 [ 35.288867] device_release_driver_internal+0xe4/0x1b0 [ 35.293998] device_release_driver+0x14/0x20 [ 35.298261] bus_remove_device+0x110/0x128 [ 35.302350] device_del+0x148/0x370 [ 35.305832] usb_disable_device+0x8c/0x1d0 [ 35.309921] usb_disconnect+0xc8/0x2d0 [ 35.313663] hub_event+0x6e0/0x1128 [ 35.317146] process_one_work+0x1e0/0x320 [ 35.321148] worker_thread+0x40/0x450 [ 35.324805] kthread+0x124/0x128 [ 35.328027] ret_from_fork+0x10/0x18 [ 35.331594] handlers: [ 35.333862] [<0000000079300c1d>] usb_hcd_irq [ 35.338126] [<0000000079300c1d>] usb_hcd_irq [ 35.342389] Disabling IRQ #156 ohci_shutdown() disables all the interrupt and rh_state is set to OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF is possible to be set by start_ed_unlink() which is called: ohci_irq() -> process_done_list() -> takeback_td() -> start_ed_unlink() So, ohci_irq() has the following condition, the issue happens by &ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and ohci->rh_state = OHCI_RH_HALTED: /* interrupt for some other device? */ if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED)) return IRQ_NOTMINE; To fix the issue, ohci_shutdown() holds the spin lock while disabling the interruption and changing the rh_state flag to prevent reenable the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also calls the ohci_shutdown() and it already held the spin lock, so that the patch makes a new function as _ohci_shutdown(). This patch is inspired by a Renesas R-Car Gen3 BSP patch from Tho Vu. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a349b95d7ca0cea71be4a7dac29830703de7eb62 upstream.

This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.

[   34.851754] usb 2-1: USB disconnect, device number 2
[   35.166658] irq 156: nobody cared (try booting with the "irqpoll" option)
[   35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85
[   35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[   35.187886] Workqueue: usb_hub_wq hub_event
[   35.192063] Call trace:
[   35.194509]  dump_backtrace+0x0/0x150
[   35.198165]  show_stack+0x14/0x20
[   35.201475]  dump_stack+0xa0/0xc4
[   35.204785]  __report_bad_irq+0x34/0xe8
[   35.208614]  note_interrupt+0x2cc/0x318
[   35.212446]  handle_irq_event_percpu+0x5c/0x88
[   35.216883]  handle_irq_event+0x48/0x78
[   35.220712]  handle_fasteoi_irq+0xb4/0x188
[   35.224802]  generic_handle_irq+0x24/0x38
[   35.228804]  __handle_domain_irq+0x5c/0xb0
[   35.232893]  gic_handle_irq+0x58/0xa8
[   35.236548]  el1_irq+0xb8/0x180
[   35.239681]  __do_softirq+0x94/0x23c
[   35.243253]  irq_exit+0xd0/0xd8
[   35.246387]  __handle_domain_irq+0x60/0xb0
[   35.250475]  gic_handle_irq+0x58/0xa8
[   35.254130]  el1_irq+0xb8/0x180
[   35.257268]  kernfs_find_ns+0x5c/0x120
[   35.261010]  kernfs_find_and_get_ns+0x3c/0x60
[   35.265361]  sysfs_unmerge_group+0x20/0x68
[   35.269454]  dpm_sysfs_remove+0x2c/0x68
[   35.273284]  device_del+0x80/0x370
[   35.276683]  hid_destroy_device+0x28/0x60
[   35.280686]  usbhid_disconnect+0x4c/0x80
[   35.284602]  usb_unbind_interface+0x6c/0x268
[   35.288867]  device_release_driver_internal+0xe4/0x1b0
[   35.293998]  device_release_driver+0x14/0x20
[   35.298261]  bus_remove_device+0x110/0x128
[   35.302350]  device_del+0x148/0x370
[   35.305832]  usb_disable_device+0x8c/0x1d0
[   35.309921]  usb_disconnect+0xc8/0x2d0
[   35.313663]  hub_event+0x6e0/0x1128
[   35.317146]  process_one_work+0x1e0/0x320
[   35.321148]  worker_thread+0x40/0x450
[   35.324805]  kthread+0x124/0x128
[   35.328027]  ret_from_fork+0x10/0x18
[   35.331594] handlers:
[   35.333862] [<0000000079300c1d>] usb_hcd_irq
[   35.338126] [<0000000079300c1d>] usb_hcd_irq
[   35.342389] Disabling IRQ #156

ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
 ohci_irq()
  -> process_done_list()
   -> takeback_td()
    -> start_ed_unlink()

So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:

	/* interrupt for some other device? */
	if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
		return IRQ_NOTMINE;

To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().

This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: host: fotg2: restart hcd after port reset 2019-09-06T08:20:46+00:00 Hans Ulli Kroll ulli.kroll@googlemail.com 2019-08-10T15:04:58+00:00 8e32498a18f8238d71ccd5c0b0585f8867b4f8a2 [ Upstream commit 777758888ffe59ef754cc39ab2f275dc277732f4 ] On the Gemini SoC the FOTG2 stalls after port reset so restart the HCD after each port reset. Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190810150458.817-1-linus.walleij@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 777758888ffe59ef754cc39ab2f275dc277732f4 ]

On the Gemini SoC the FOTG2 stalls after port reset
so restart the HCD after each port reset.

Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190810150458.817-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
usb: host: xhci-rcar: Fix timeout in xhci_suspend() 2019-08-16T08:13:49+00:00 Yoshihiro Shimoda yoshihiro.shimoda.uh@renesas.com 2019-08-02T08:33:35+00:00 b1a8577803d793a2ec06192bc2bd92c343a0e756 commit 783bda5e41acc71f98336e1a402c180f9748e5dc upstream. When a USB device is connected to the host controller and the system enters suspend, the following error happens in xhci_suspend(): xhci-hcd ee000000.usb: WARN: xHC CMD_RUN timeout Since the firmware/internal CPU control the USBSTS.STS_HALT and the process speed is down when the roothub port enters U3, long delay for the handshake of STS_HALT is neeed in xhci_suspend(). So, this patch adds to set the XHCI_SLOW_SUSPEND. Fixes: 435cc1138ec9 ("usb: host: xhci-plat: set resume_quirk() for R-Car controllers") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/1564734815-17964-1-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 783bda5e41acc71f98336e1a402c180f9748e5dc upstream.

When a USB device is connected to the host controller and
the system enters suspend, the following error happens
in xhci_suspend():

	xhci-hcd ee000000.usb: WARN: xHC CMD_RUN timeout

Since the firmware/internal CPU control the USBSTS.STS_HALT
and the process speed is down when the roothub port enters U3,
long delay for the handshake of STS_HALT is neeed in xhci_suspend().
So, this patch adds to set the XHCI_SLOW_SUSPEND.

Fixes: 435cc1138ec9 ("usb: host: xhci-plat: set resume_quirk() for R-Car controllers")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1564734815-17964-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: pci-quirks: Correct AMD PLL quirk detection 2019-07-31T05:28:57+00:00 Ryan Kennedy ryan5544@gmail.com 2019-07-04T15:35:28+00:00 e25ec1499721beabd1916e9d8283a65b4d6349bd commit f3dccdaade4118070a3a47bef6b18321431f9ac6 upstream. The AMD PLL USB quirk is incorrectly enabled on newer Ryzen chipsets. The logic in usb_amd_find_chipset_info currently checks for unaffected chipsets rather than affected ones. This broke once a new chipset was added in e788787ef. It makes more sense to reverse the logic so it won't need to be updated as new chipsets are added. Note that the core of the workaround in usb_amd_quirk_pll does correctly check the chipset. Signed-off-by: Ryan Kennedy <ryan5544@gmail.com> Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume") Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20190704153529.9429-2-ryan5544@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit f3dccdaade4118070a3a47bef6b18321431f9ac6 upstream.

The AMD PLL USB quirk is incorrectly enabled on newer Ryzen
chipsets. The logic in usb_amd_find_chipset_info currently checks
for unaffected chipsets rather than affected ones. This broke
once a new chipset was added in e788787ef. It makes more sense
to reverse the logic so it won't need to be updated as new
chipsets are added. Note that the core of the workaround in
usb_amd_quirk_pll does correctly check the chipset.

Signed-off-by: Ryan Kennedy <ryan5544@gmail.com>
Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190704153529.9429-2-ryan5544@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>