linux-stable.git/drivers/usb/host, branch v3.7.9

USB: EHCI: fix for leaking isochronous data

2013-02-11T17:04:46+00:00

commit b09a61cc0bc2a7151f4ab652489e85253d5d0175 upstream.

This patch (as1653) fixes a bug in ehci-hcd.  Unlike iTD entries, an
siTD entry in the periodic schedule may not complete until the frame
after the one it belongs to.  Consequently, when scanning the periodic
schedule it is necessary to start with the frame _preceding_ the one
where the previous scan ended.

Not doing this properly can result in memory leaks and failures to
complete isochronous URBs.

Signed-off-by: Alan Stern 
Reported-and-tested-by: Andy Leiserson 
Signed-off-by: Greg Kroah-Hartman

usb: Prevent dead ports when xhci is not enabled

2013-02-11T17:04:46+00:00

commit 58b2939b4d5a030eaec469d29812ab8477ee7e76 upstream.

When the xHCI driver is not available, actively switch the ports to EHCI
mode since some BIOSes leave them in xHCI mode where they would
otherwise appear dead.  This was discovered on a  Dell Optiplex 7010,
but it's possible other systems could be affected.

This should be backported to kernels as old as 3.0, that contain the
commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."

Signed-off-by: David Moore 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

USB: XHCI: fix memory leak of URB-private data

2013-02-11T17:04:46+00:00

commit 48c3375c5f69b1c2ef3d1051a0009cb9bce0ce24 upstream.

This patch (as1640) fixes a memory leak in xhci-hcd.  The urb_priv
data structure isn't always deallocated in the handle_tx_event()
routine for non-control transfers.  The patch adds a kfree() call so
that all paths end up freeing the memory properly.

This patch should be backported to kernels as old as 2.6.36, that
contain the commit 8e51adccd4c4b9ffcd509d7f2afce0a906139f75 "USB: xHCI:
Introduce urb_priv structure"

Signed-off-by: Alan Stern 
Signed-off-by: Sarah Sharp 
Reported-and-tested-by: Martin Mokrejs 
Signed-off-by: Greg Kroah-Hartman

xhci: Fix TD size for isochronous URBs.

2013-02-11T17:04:46+00:00

commit f18f8ed2a9adc41c2d9294b85b6af115829d2af1 upstream.

To calculate the TD size for a particular TRB in an isoc TD, we need
know the endpoint's max packet size.  Isochronous endpoints also encode
the number of additional service opportunities in their wMaxPacketSize
field.  The TD size calculation did not mask off those bits before using
the field.  This resulted in incorrect TD size information for
isochronous TRBs when an URB frame buffer crossed a 64KB boundary.

For example:
 - an isoc endpoint has 2 additional service opportunites and
   a max packet size of 1020 bytes
 - a frame transfer buffer contains 3060 bytes
 - one frame buffer crosses a 64KB boundary, and must be split into
   one 1276 byte TRB, and one 1784 byte TRB.

The TD size is is the number of packets that remain to be transferred
for a TD after processing all the max packet sized packets in the
current TRB and all previous TRBs.

For this TD, the number of packets to be transferred is (3060 / 1020),
or 3.  The first TRB contains 1276 bytes, which means it contains one
full packet, and a 256 byte remainder.  After processing all the max
packet-sized packets in the first TRB, the host will have 2 packets left
to transfer.

The old code would calculate the TD size for the first TRB as:

total packet count = DIV_ROUND_UP (TD length / endpoint wMaxPacketSize)
total packet count - (first TRB length / endpoint wMaxPacketSize)

The math should have been:

total packet count = DIV_ROUND_UP (3060 / 1020) = 3
3 - (1276 / 1020) = 2

Since the old code didn't mask off the additional service interval bits
from the wMaxPacketSize field, the math ended up as

total packet count = DIV_ROUND_UP (3060 / 5116) = 1
1 - (1276 / 5116) = 1

Fix this by masking off the number of additional service opportunities
in the wMaxPacketSize field.

This patch should be backported to stable kernels as old as 3.0, that
contain the commit 4da6e6f247a2601ab9f1e63424e4d944ed4124f3 "xhci 1.0:
Update TD size field format."  It may not apply well to kernels older
than 3.2 because of commit 29cc88979a8818cd8c5019426e945aed118b400e
"USB: use usb_endpoint_maxp() instead of le16_to_cpu()".

Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

xhci: Fix isoc TD encoding.

2013-02-11T17:04:46+00:00

commit 760973d2a74b93eb1697981f7448f0e62767cfc4 upstream.

An isochronous TD is comprised of one isochronous TRB chained to zero or
more normal TRBs.  Only the isoc TRB has the TBC and TLBPC fields.  The
normal TRBs must set those fields to zeroes.  The code was setting the
TBC and TLBPC fields for both isoc and normal TRBs.  Fix this.

This should be backported to stable kernels as old as 3.0, that contain
the commit b61d378f2da41c748aba6ca19d77e1e1c02bcea5 " xhci 1.0: Set
transfer burst last packet count field."

Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

drivers: xhci: fix incorrect bit test

2013-02-11T17:04:46+00:00

commit ba7b5c22d33136a5612ca5ef8d31564dcc501126 upstream.

Fix incorrect bit test that originally showed up in
4ee823b83bc9851743fab756c76b27d6a1e2472b "USB/xHCI: Support
device-initiated USB 3.0 resume."

Use '&' instead of '&&'.

This should be backported to kernels as old as 3.4.

Signed-off-by: Nickolai Zeldovich 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

USB: EHCI: fix bug in scheduling periodic split transfers

2013-02-11T17:04:45+00:00

commit 3e619d04159be54b3daa0b7036b0ce9e067f4b5d upstream.

This patch (as1654) fixes a very old bug in ehci-hcd, connected with
scheduling of periodic split transfers.  The calculations for
full/low-speed bus usage are all carried out after the correction for
bit-stuffing has been applied, but the values in the max_tt_usecs
array assume it hasn't been.  The array should allow for allocation of
up to 90% of the bus capacity, which is 900 us, not 780 us.

The symptom caused by this bug is that any isochronous transfer to a
full-speed device with a maxpacket size larger than about 980 bytes is
always rejected with a -ENOSPC error.

Signed-off-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: EHCI: fix timer bug affecting port resume

2013-02-11T17:04:45+00:00

commit ee74290b7853db9d5fd64db70e5c175241c59fba upstream.

This patch (as1652) fixes a long-standing bug in ehci-hcd.  The driver
relies on status polls to know when to stop port-resume signalling.
It uses the root-hub status timer to schedule these status polls.  But
when the driver for the root hub is resumed, the timer is rescheduled
to go off immediately -- before the port is ready.  When this happens
the timer does not get re-enabled, which prevents the port resume from
finishing until some other event occurs.

The symptom is that when a new device is plugged in, it doesn't get
recognized or enumerated until lsusb is run or something else happens.

The solution is to re-enable the root-hub status timer after every
status poll while a port resume is in progress.

This bug hasn't surfaced before now because we never used to try to
suspend the root hub in the middle of a port resume (except by
coincidence).

Signed-off-by: Alan Stern 
Reported-and-tested-by: Norbert Preining 
Tested-by: Ming Lei 
Signed-off-by: Greg Kroah-Hartman

USB: EHCI: unlink one async QH at a time

2013-02-11T17:04:45+00:00

commit 6e0c3339a6f19d748f16091d0a05adeb1e1f822b upstream.

This patch (as1648) fixes a regression affecting nVidia EHCI
controllers.  Evidently they don't like to have more than one async QH
unlinked at a time.  I can't imagine how they manage to mess it up,
but at least one of them does.

The patch changes the async unlink logic in two ways:

	Each time an IAA cycle is started, only the first QH on the
	async unlink list is handled (rather than all of them).

	Async QHs do not all get unlinked as soon as they have been
	empty for long enough.  Instead, only the last one (i.e., the
	one that has been on the schedule the longest) is unlinked,
	and then only if no other unlinks are in progress at the time.

This means that when multiple QHs are empty, they won't be unlinked as
quickly as before.  That's okay; it won't affect correct operation of
the driver or add an excessive load.  Multiple unlinks tend to be
relatively rare in any case.

Signed-off-by: Alan Stern 
Reported-and-tested-by: Piergiorgio Sartor 
Signed-off-by: Greg Kroah-Hartman

USB: EHCI: remove ASS/PSS polling timeout

2013-02-11T17:04:45+00:00

commit 55bcdce8a8228223ec4d17d8ded8134ed265d2c5 upstream.

This patch (as1647) attempts to work around a problem that seems to
affect some nVidia EHCI controllers.  They sometimes take a very long
time to turn off their async or periodic schedules.  I don't know if
this is a result of other problems, but in any case it seems wise not
to depend on schedule enables or disables taking effect in any
specific length of time.

The patch removes the existing 20-ms timeout for enabling and
disabling the schedules.  The driver will now continue to poll the
schedule state at 1-ms intervals until the controller finally decides
to obey the most recent command issued by the driver.  Just in case
this hides a problem, a debugging message will be logged if the
controller takes longer than 20 polls.

I don't know if this will actually fix anything, but it can't hurt.

Signed-off-by: Alan Stern 
Tested-by: Piergiorgio Sartor 
Signed-off-by: Greg Kroah-Hartman