linux-stable.git/drivers/usb/host, branch v3.4

USB: ehci-tegra: remove redundant gpio_set_value

2012-05-01T18:11:51+00:00

The immediately preceding gpio_direction_output() already set the value,
so there's no need to repeat it. This also prevents gpio_set_value() from
WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set
direction API is always sleepable, but plain set_value isn't.

Cc:  # v3.3
Signed-off-by: Stephen Warren 
Signed-off-by: Greg Kroah-Hartman

EHCI: update PM methods in ehci-tegra.c

2012-05-01T18:06:36+00:00

This patch (as1547) rearranges the Power Management parts of the
ehci-tegra driver to match the conventions used in other EHCI platform
drivers.  In particular, the controller should not be powered down by
the root hub's suspend routine; the controller's power level should be
managed by the controller's own PM methods.

The end result of the patch is that the standard ehci_bus_suspend()
and ehci_bus_resume() methods can be used instead of special-purpose
routines.  The driver now uses the standard dev_pm_ops methods instead
of legacy power management.  Since there is no supported wakeup
mechanism for the controller, runtime suspend is forbidden by default
(this can be overridden via sysfs, if desired).

These adjustments are needed in order to make ehci-tegra compatible
with recent changes to the USB core.  The core now checks the root
hub's status following bus suspend; if the controller is automatically
powered down during bus suspend then the check will fail and the root
hub will be resumed immediately.  Doing the controller power-down in a
separate method avoids this problem.

Signed-off-by: Alan Stern 
Acked-by: Stephen Warren 
Tested-by: Stephen Warren 
Signed-off-by: Greg Kroah-Hartman

USB: EHCI: fix crash during suspend on ASUS computers

2012-04-24T20:55:43+00:00

This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

This fixes Bugzilla #42728.

Signed-off-by: Alan Stern 
Tested-by: Steven Rostedt 
Tested-by: Andrey Rahmatullin 
Tested-by: Oleksij Rempel (fishor) 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2012-04-21T19:45:52+00:00

Pull "ARM: SoC fixes" from Olof Johansson:
 * at91, ux500, imx, omap and bcmring:
  - at91 fixes for =m driver build issues, irqdomain fixes and config
    dependency fixes
  - ux500 kconfig dependency fixes and a  smp wakeup bugfix
  - imx idle bugfix and build fix due to irq domain changes
  - omap uart pinmux fixes, softreset regression revert and misc fixes
  - bcmring build error regression fix

 * ux500 and imx had some small defconfig updates in this branch

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
  ARM: bcmring: fix UART declarations
  ARM: imx: Fix imx5 idle logic bug
  ARM: imx27-dt: Fix build due to removal of irq_domain_add_simple()
  ARM: imx_v4_v5_defconfig: Add support for CONFIG_REGULATOR_FIXED_VOLTAGE
  ARM: OMAP1: DMTIMER: fix broken timer clock source selection
  ARM: OMAP: serial: Fix the ocp smart idlemode handling bug
  ARM: OMAP2+: UART: Fix incorrect population of default uart pads
  ARM: OMAP: sram: fix BUG in dpll code for !PM case
  dmaengine: Kconfig: fix Atmel at_hdmac entry
  USB: gadget/at91_udc: add gpio_to_irq() function to vbus interrupt
  USB: ohci-at91: change annotations for probe/remove functions
  leds-atmel-pwm.c: Make pwmled_probe() __devinit
  ARM: at91: fix at91sam9261ek Ethernet dm9000 irq
  ARM: at91: fix rm9200ek flash size
  ARM: at91: remove empty at91_init_serial function
  ARM: at91: fix typo in at91_pmc_base assembly declaration
  ARM: at91: Export at91_matrix_base
  ARM: at91: Export at91_pmc_base
  ARM: at91: Export at91_ramc_base
  ARM: at91: Export at91_st_base
  ...

Merge tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6

2012-04-21T19:42:12+00:00

Pull MFD fixes from Samuel Ortiz:
 "We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040
  conversion to an i2c driver.  The latter may not sound like a fix but
  the twl6040 MFD driver won't probe without it, triggering an OMAP4
  audio regression."

* tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: Fix modular builds of rc5t583 regulator support
  mfd: Fix asic3_gpio_to_irq
  ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue
  mfd: Convert twl6040 to i2c driver, and separate it from twl core
  mfd : Fix dbx500 compilation error

USB: ehci-tegra: don't call set_irq_flags(IRQF_VALID)

2012-04-18T21:17:33+00:00

This call is not needed; the IRQ controller should (and does) set up
interrupts correctly. set_irq_flags() isn't exported to modules, to
this also fixes compilation of ehci-tegra.c as a module.

Signed-off-by: Stephen Warren 
Signed-off-by: Greg Kroah-Hartman

USB: ehci-fsl: Fix kernel crash on mpc5121e

2012-04-18T21:13:52+00:00

Since commit 28c56ea1431421dec51b7b229369e991481453df
(powerpc/usb: fix bug of kernel hang when initializing usb)
the kernel crashes on mpc5121e. mpc5121e doesn't have system interface
registers, accessing this register address space cause the machine check
exception and a kernel crash:
...
[    1.294596] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.316491] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[    1.337334] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[    1.358548] Machine check in kernel mode.
[    1.375917] Caused by (from SRR1=49030): Transfer error ack signal
[    1.395505] Oops: Machine check, sig: 7 [#1]
[    1.413113] MPC5121 ADS
[    1.428718] Modules linked in:
[    1.444841] NIP: c026efc4 LR: c0278b50 CTR: 00000000
[    1.463342] REGS: df837ba0 TRAP: 0200   Not tainted  (3.3.0-08839-gb5174fa)
[    1.484083] MSR: 00049030   CR: 42042022  XER: 20000000
[    1.504099] TASK = df834000[1] 'swapper' THREAD: df836000
[    1.509667] GPR00: 1c000000 df837c50 df834000 df9d74e0 00000003 00000010 00000000 00000000
[    1.531650] GPR08: 00000020 00000000 c037cdd8 e1088000 22042028 1001a69c 00000000 00000000
[    1.553762] GPR16: 1ffbce70 00000000 1fef5b28 1fef3e08 00000000 00000000 1ffcbc7c c045b264
[    1.575824] GPR24: 0000008b 00000002 c04a7dd0 e1088000 df33c960 df9d74e0 00000000 df9d7400
[    1.612295] NIP [c026efc4] ehci_fsl_setup_phy+0x110/0x124
[    1.632454] LR [c0278b50] ehci_fsl_setup+0x29c/0x304
[    1.652065] Call Trace:
[    1.668923] [df837c50] [c0278a40] ehci_fsl_setup+0x18c/0x304 (unreliable)
[    1.690332] [df837c70] [c025cba4] usb_add_hcd+0x1f0/0x66c
[    1.710377] [df837cb0] [c0277ab8] ehci_fsl_drv_probe+0x180/0x308
[    1.731322] [df837ce0] [c01fc7a8] platform_drv_probe+0x20/0x30
[    1.752202] [df837cf0] [c01fb0ac] driver_probe_device+0x8c/0x214
[    1.773491] [df837d10] [c01f956c] bus_for_each_drv+0x6c/0xa8
[    1.794279] [df837d40] [c01fafdc] device_attach+0xb4/0xd8
[    1.814574] [df837d60] [c01fa44c] bus_probe_device+0xa4/0xb4
[    1.835343] [df837d80] [c01f87a8] device_add+0x52c/0x5dc
[    1.855462] [df837dd0] [c01fcd58] platform_device_add+0x124/0x1d0
[    1.876558] [df837df0] [c036dcec] fsl_usb2_device_register+0xa0/0xd4
[    1.897512] [df837e10] [c036df28] fsl_usb2_mph_dr_of_probe+0x208/0x264
[    1.918253] [df837e90] [c01fc7a8] platform_drv_probe+0x20/0x30
[    1.938300] [df837ea0] [c01fb0ac] driver_probe_device+0x8c/0x214
[    1.958511] [df837ec0] [c01fb2f0] __driver_attach+0xbc/0xc0
[    1.978088] [df837ee0] [c01f9608] bus_for_each_dev+0x60/0x9c
[    1.997589] [df837f10] [c01fab88] driver_attach+0x24/0x34
[    2.016757] [df837f20] [c01fa744] bus_add_driver+0x1ac/0x274
[    2.036339] [df837f50] [c01fb898] driver_register+0x88/0x150
[    2.056052] [df837f70] [c01fcabc] platform_driver_register+0x68/0x78
[    2.076650] [df837f80] [c0446500] fsl_usb2_mph_dr_driver_init+0x18/0x28
[    2.097734] [df837f90] [c0003988] do_one_initcall+0x148/0x1b0
[    2.117934] [df837fc0] [c042d89c] kernel_init+0xfc/0x190
[    2.137667] [df837ff0] [c000d2c4] kernel_thread+0x4c/0x68
[    2.157240] Instruction dump:
[    2.174119] 90050004 4e800020 2f840003 419e0014 2f840004 409eff64 6400c000 4bffff5c
[    2.196000] 64001000 7c0004ac 812b0500 0c090000 <4c00012c> 61290200 7c0004ac 912b0500
[    2.218100] ---[ end trace 21659aedb84ad816 ]---
[    2.237089]
[    3.232940] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
[    3.232954]
[    3.271575] Rebooting in 1 seconds..

Check pdata->have_sysif_regs flag before accessing system interface
registers.

Signed-off-by: Anatolij Gustschin 
Cc: Shengzhou Liu 
Signed-off-by: Greg Kroah-Hartman

EHCI: always clear the STS_FLR status bit

2012-04-18T20:06:59+00:00

This patch (as1544) fixes a problem affecting some EHCI controllers.
They can generate interrupts whenever the STS_FLR status bit is turned
on, even though that bit is masked out in the Interrupt Enable
register.

Since the driver doesn't use STS_FLR anyway, the patch changes the
interrupt routine to clear that bit whenever it is set, rather than
leaving it alone.

Signed-off-by: Alan Stern 
Reported-and-tested-by: Tomoya MORINAGA 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

EHCI: fix criterion for resuming the root hub

2012-04-17T22:54:58+00:00

This patch (as1542) changes the criterion ehci-hcd uses to tell when
it needs to resume the controller's root hub.  A resume is needed when
a port status change is detected, obviously, but only if the root hub
is currently suspended.

Right now the driver tests whether the root hub is running, and that
is not the correct test.  In particular, if the controller has died
then the root hub should not be restarted.  In addition, some buggy
hardware occasionally requires the root hub to be running and
sending out SOF packets even while it is nominally supposed to be
suspended.

In the end, the test needs to be changed.  Rather than checking whether
the root hub is currently running, the driver will now check whether
the root hub is currently suspended.  This will yield the correct
behavior in all cases.

Signed-off-by: Alan Stern 
CC: Peter Chen 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: ohci-at91: change annotations for probe/remove functions

2012-04-17T14:29:32+00:00

Add __devinit and __devexit on *_probe() and *_remove() functions
with proper modification of struct platform_driver.

Signed-off-by: Nicolas Ferre 
Acked-by: Alan Stern 
Cc: linux-usb@vger.kernel.org