linux-stable.git/drivers/usb/host, branch v3.3.8 Linux kernel stable tree USB: fix resource leak in xhci power loss path 2012-06-01T07:15:50+00:00 Oliver Neukum oneukum@suse.de 2012-05-10T08:19:21+00:00 8ccb02914be80e1ca08fe978e8a02e472f9d143c commit f8a9e72d125f4e00ec529ba67b674321a1f3bf31 upstream. Some more data structures must be freed and counters reset if an XHCI controller has lost power. The failure to do so renders some chips inoperative after a certain number of S4 cycles. This patch should be backported to kernels as old as 3.2, that contain the commits c29eea621900f18287d50519f72cb9113746d75a "xhci: Implement HS/FS/LS bandwidth checking." and commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe "xhci: Implement HS/FS/LS bandwidth checking." Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit f8a9e72d125f4e00ec529ba67b674321a1f3bf31 upstream.

Some more data structures must be freed and counters
reset if an XHCI controller has lost power. The failure
to do so renders some chips inoperative after a certain number
of S4 cycles.

This patch should be backported to kernels as old as 3.2,
that contain the commits c29eea621900f18287d50519f72cb9113746d75a
"xhci: Implement HS/FS/LS bandwidth checking." and
commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe
"xhci: Implement HS/FS/LS bandwidth checking."

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Add new short TX quirk for Fresco Logic host. 2012-06-01T07:15:49+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-05-08T16:22:49+00:00 904590abe2a30abe7fc3345fde087a91c21db2e1 commit 1530bbc6272d9da1e39ef8e06190d42c13a02733 upstream. Sergio reported that when he recorded audio from a USB headset mic plugged into the USB 3.0 port on his ASUS N53SV-DH72, the audio sounded "robotic". When plugged into the USB 2.0 port under EHCI on the same laptop, the audio sounded fine. The device is: Bus 002 Device 004: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset The problem was tracked down to the Fresco Logic xHCI host controller not correctly reporting short transfers on isochronous IN endpoints. The driver would submit a 96 byte transfer, the device would only send 88 or 90 bytes, and the xHCI host would report the transfer had a "successful" completion code, with an untransferred buffer length of 8 or 6 bytes. The successful completion code and non-zero untransferred length is a contradiction. The xHCI host is supposed to only mark a transfer as successful if all the bytes are transferred. Otherwise, the transfer should be marked with a short packet completion code. Without the EHCI bus trace, we wouldn't know whether the xHCI driver should trust the completion code or the untransferred length. With it, we know to trust the untransferred length. Add a new xHCI quirk for the Fresco Logic host controller. If a transfer is reported as successful, but the untransferred length is non-zero, print a warning. For the Fresco Logic host, change the completion code to COMP_SHORT_TX and process the transfer like a short transfer. This should be backported to stable kernels that contain the commit f5182b4155b9d686c5540a6822486400e34ddd98 "xhci: Disable MSI for some Fresco Logic hosts." That commit was marked for stable kernels as old as 2.6.36. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Sergio Correia <lists@uece.net> Tested-by: Sergio Correia <lists@uece.net> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 1530bbc6272d9da1e39ef8e06190d42c13a02733 upstream.

Sergio reported that when he recorded audio from a USB headset mic
plugged into the USB 3.0 port on his ASUS N53SV-DH72, the audio sounded
"robotic".  When plugged into the USB 2.0 port under EHCI on the same
laptop, the audio sounded fine.  The device is:

Bus 002 Device 004: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset

The problem was tracked down to the Fresco Logic xHCI host controller
not correctly reporting short transfers on isochronous IN endpoints.
The driver would submit a 96 byte transfer, the device would only send
88 or 90 bytes, and the xHCI host would report the transfer had a
"successful" completion code, with an untransferred buffer length of 8
or 6 bytes.

The successful completion code and non-zero untransferred length is a
contradiction.  The xHCI host is supposed to only mark a transfer as
successful if all the bytes are transferred.  Otherwise, the transfer
should be marked with a short packet completion code.  Without the EHCI
bus trace, we wouldn't know whether the xHCI driver should trust the
completion code or the untransferred length.  With it, we know to trust
the untransferred length.

Add a new xHCI quirk for the Fresco Logic host controller.  If a
transfer is reported as successful, but the untransferred length is
non-zero, print a warning.  For the Fresco Logic host, change the
completion code to COMP_SHORT_TX and process the transfer like a short
transfer.

This should be backported to stable kernels that contain the commit
f5182b4155b9d686c5540a6822486400e34ddd98 "xhci: Disable MSI for some
Fresco Logic hosts."  That commit was marked for stable kernels as old
as 2.6.36.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Sergio Correia <lists@uece.net>
Tested-by: Sergio Correia <lists@uece.net>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Reset reserved command ring TRBs on cleanup. 2012-06-01T07:15:49+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-05-08T14:09:26+00:00 66c4d8a0d9b4732d5792b658a6bd879d94c3da46 commit 33b2831ac870d50cc8e01c317b07fb1e69c13fe1 upstream. When the xHCI driver needs to clean up memory (perhaps due to a failed register restore on resume from S3 or resume from S4), it needs to reset the number of reserved TRBs on the command ring to zero. Otherwise, several resume cycles (about 30) with a UAS device attached will continually increment the number of reserved TRBs, until all command submissions fail because there isn't enough room on the command ring. This patch should be backported to kernels as old as 2.6.32, that contain the commit 913a8a344ffcaf0b4a586d6662a2c66a7106557d "USB: xhci: Change how xHCI commands are handled." Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 33b2831ac870d50cc8e01c317b07fb1e69c13fe1 upstream.

When the xHCI driver needs to clean up memory (perhaps due to a failed
register restore on resume from S3 or resume from S4), it needs to reset
the number of reserved TRBs on the command ring to zero.  Otherwise,
several resume cycles (about 30) with a UAS device attached will
continually increment the number of reserved TRBs, until all command
submissions fail because there isn't enough room on the command ring.

This patch should be backported to kernels as old as 2.6.32,
that contain the commit 913a8a344ffcaf0b4a586d6662a2c66a7106557d
"USB: xhci: Change how xHCI commands are handled."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb-xhci: Handle COMP_TX_ERR for isoc tds 2012-06-01T07:15:49+00:00 Hans de Goede hdegoede@redhat.com 2012-04-23T13:06:09+00:00 540304dabfad54a3b9171cc8c310831a8c273535 commit 9c745995ae5c4ff787f34a359de908facc11ee00 upstream. While testing unplugging an UVC HD webcam with usb-redirection (so through usbdevfs), my userspace usb-redir code was getting a value of -1 in iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt is not a valid value. The source of this -1 is the default case in xhci-ring.c:process_isoc_td() adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR in this case, so this patch adds handling for that completion code to process_isoc_td(). This was observed and tested with the following xhci controller: 1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can do, but since I cannot come up with anything better I've left that as is. This patch should be backported to kernels as old as 2.6.36, which contain the commit 04e51901dd44f40a5a385ced897f6bca87d5f40a "USB: xHCI: Isochronous transfer implementation". Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 9c745995ae5c4ff787f34a359de908facc11ee00 upstream.

While testing unplugging an UVC HD webcam with usb-redirection (so through
usbdevfs), my userspace usb-redir code was getting a value of -1 in
iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt
is not a valid value.

The source of this -1 is the default case in xhci-ring.c:process_isoc_td()
adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR
in this case, so this patch adds handling for that completion code to
process_isoc_td().

This was observed and tested with the following xhci controller:
1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)

Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can
do, but since I cannot come up with anything better I've left that as is.

This patch should be backported to kernels as old as 2.6.36, which contain the
commit 04e51901dd44f40a5a385ced897f6bca87d5f40a "USB: xHCI: Isochronous
transfer implementation".

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Avoid dead ports when CONFIG_USB_XHCI_HCD=n 2012-06-01T07:15:49+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-04-16T17:56:47+00:00 829cd2d3f62dd84a14c4d80cbb24f46bf5e591e7 commit 51c9e6c7732b67769c0a514d31f505e49fa82dd4 upstream. If the user chooses to say "no" to CONFIG_USB_XHCI_HCD on a system with an Intel Panther Point chipset, the PCI quirks code or the EHCI driver will switch the ports over to the xHCI host, but the xHCI driver will never load. The ports will be powered off and seem "dead" to the user. Fix this by only switching the ports over if CONFIG_USB_XHCI_HCD is either compiled in, or compiled as a module. This patch should be backported to stable kernels as old as 3.0, that contain commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Eric Anholt <eric.anholt@intel.com> Reported-by: David Bein <d.bein@f5.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 51c9e6c7732b67769c0a514d31f505e49fa82dd4 upstream.

If the user chooses to say "no" to CONFIG_USB_XHCI_HCD on a system
with an Intel Panther Point chipset, the PCI quirks code or the EHCI
driver will switch the ports over to the xHCI host, but the xHCI driver
will never load.  The ports will be powered off and seem "dead" to the
user.

Fix this by only switching the ports over if CONFIG_USB_XHCI_HCD is
either compiled in, or compiled as a module.

This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Eric Anholt <eric.anholt@intel.com>
Reported-by: David Bein <d.bein@f5.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Add Lynx Point to list of Intel switchable hosts. 2012-06-01T07:15:49+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-02-09T23:55:13+00:00 ea650a02e573f8588b4b35f66219326e7e2c81a6 commit 1c12443ab8eba71a658fae4572147e56d1f84f66 upstream. The upcoming Intel Lynx Point chipset includes an xHCI host controller that can have ports switched from the EHCI host controller, just like the Intel Panther Point xHCI host. This time, ports from both EHCI hosts can be switched to the xHCI host controller. The PCI config registers to do the port switching are in the exact same place in the xHCI PCI configuration registers, with the same semantics. Hooray for shipping patches for next-gen hardware before the current gen hardware is even available for purchase! This patch should be backported to stable kernels as old as 3.0, that contain commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 1c12443ab8eba71a658fae4572147e56d1f84f66 upstream.

The upcoming Intel Lynx Point chipset includes an xHCI host controller
that can have ports switched from the EHCI host controller, just like
the Intel Panther Point xHCI host.  This time, ports from both EHCI
hosts can be switched to the xHCI host controller.  The PCI config
registers to do the port switching are in the exact same place in the
xHCI PCI configuration registers, with the same semantics.

Hooray for shipping patches for next-gen hardware before the current gen
hardware is even available for purchase!

This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: ohci-at91: add a reset function to fix race condition 2012-06-01T07:15:48+00:00 Nicolas Ferre nicolas.ferre@atmel.com 2012-05-09T08:48:54+00:00 fdda49b01c157b6723137040e2033fe92188903c commit 07e4e556eff4938eb2edf2591de3aa7d7fb82b52 upstream. A possible race condition appears because we are not initializing the ohci->regs before calling usb_hcd_request_irqs(). We move the call to ohci_init() in hcd->driver->reset() instead of hcd->driver->start() to fix this. This was experienced when we share the same IRQ line between OHCI and EHCI controllers. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Tested-by: Christian Eggers <christian.eggers@kathrein.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 07e4e556eff4938eb2edf2591de3aa7d7fb82b52 upstream.

A possible race condition appears because we are not initializing
the ohci->regs before calling usb_hcd_request_irqs().
We move the call to ohci_init() in hcd->driver->reset() instead of
hcd->driver->start() to fix this.
This was experienced when we share the same IRQ line between OHCI and EHCI
controllers.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Christian Eggers <christian.eggers@kathrein.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: ehci-tegra: remove redundant gpio_set_value 2012-05-07T15:53:24+00:00 Stephen Warren swarren@nvidia.com 2012-04-30T23:24:10+00:00 174c50cdb6104cb3c3bc1f4ff00ad20881ab00b7 commit 04c235c92ce8474e9f2b358bd97f013a500385f2 upstream. The immediately preceding gpio_direction_output() already set the value, so there's no need to repeat it. This also prevents gpio_set_value() from WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set direction API is always sleepable, but plain set_value isn't. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 04c235c92ce8474e9f2b358bd97f013a500385f2 upstream.

The immediately preceding gpio_direction_output() already set the value,
so there's no need to repeat it. This also prevents gpio_set_value() from
WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set
direction API is always sleepable, but plain set_value isn't.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: EHCI: fix crash during suspend on ASUS computers 2012-05-07T15:53:23+00:00 Alan Stern stern@rowland.harvard.edu 2012-04-24T18:07:22+00:00 1ce9245f5aff46201fa81fdd3f796a6c9f3ad1ab commit 151b61284776be2d6f02d48c23c3625678960b97 upstream. This patch (as1545) fixes a problem affecting several ASUS computers: The machine crashes or corrupts memory when going into suspend if the ehci-hcd driver is bound to any controllers. Users have been forced to unbind or unload ehci-hcd before putting their systems to sleep. After extensive testing, it was determined that the machines don't like going into suspend when any EHCI controllers are in the PCI D3 power state. Presumably this is a firmware bug, but there's nothing we can do about it except to avoid putting the controllers in D3 during system sleep. The patch adds a new flag to indicate whether the problem is present, and avoids changing the controller's power state if the flag is set. Runtime suspend is unaffected; this matters only for system suspend. However as a side effect, the controller will not respond to remote wakeup requests while the system is asleep. Hence USB wakeup is not functional -- but of course, this is already true in the current state of affairs. This fixes Bugzilla #42728. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Steven Rostedt <rostedt@goodmis.org> Tested-by: Andrey Rahmatullin <wrar@wrar.name> Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 151b61284776be2d6f02d48c23c3625678960b97 upstream.

This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

This fixes Bugzilla #42728.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EHCI: always clear the STS_FLR status bit 2012-04-27T17:16:50+00:00 Alan Stern stern@rowland.harvard.edu 2012-04-18T15:33:00+00:00 31f50d3450f96ef57a9a3f8977655cda550fbc51 commit 2fbe2bf1fd37f9d99950bd8d8093623cf22cf08b upstream. This patch (as1544) fixes a problem affecting some EHCI controllers. They can generate interrupts whenever the STS_FLR status bit is turned on, even though that bit is masked out in the Interrupt Enable register. Since the driver doesn't use STS_FLR anyway, the patch changes the interrupt routine to clear that bit whenever it is set, rather than leaving it alone. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Tomoya MORINAGA <tomoya.rohm@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2fbe2bf1fd37f9d99950bd8d8093623cf22cf08b upstream.

This patch (as1544) fixes a problem affecting some EHCI controllers.
They can generate interrupts whenever the STS_FLR status bit is turned
on, even though that bit is masked out in the Interrupt Enable
register.

Since the driver doesn't use STS_FLR anyway, the patch changes the
interrupt routine to clear that bit whenever it is set, rather than
leaving it alone.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>