linux-stable.git/drivers/usb/host, branch v3.2.71

xhci: do not report PLC when link is in internal resume state

2015-08-12T14:33:23+00:00

commit aca3a0489ac019b58cf32794d5362bb284cb9b94 upstream.

Port link change with port in resume state should not be
reported to usbcore, as this is an internal state to be
handled by xhci driver. Reporting PLC to usbcore may
cause usbcore clearing PLC first and port change event irq
won't be generated.

Signed-off-by: Zhuang Jin Can 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2:
 - Adjust indentation
 - s/raw_port_status/temp/]
Signed-off-by: Ben Hutchings

xhci: report U3 when link is in resume state

2015-08-12T14:33:23+00:00

commit 243292a2ad3dc365849b820a64868927168894ac upstream.

xhci_hub_report_usb3_link_state() returns pls as U0 when the link
is in resume state, and this causes usb core to think the link is in
U0 while actually it's in resume state. When usb core transfers
control request on the link, it fails with TRB error as the link
is not ready for transfer.

To fix the issue, report U3 when the link is in resume state, thus
usb core knows the link it's not ready for transfer.

Signed-off-by: Zhuang Jin Can 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

xhci: Calculate old endpoints correctly on device reset

2015-08-12T14:33:22+00:00

commit 326124a027abc9a7f43f72dc94f6f0f7a55b02b3 upstream.

When resetting a device the number of active TTs may need to be
corrected by xhci_update_tt_active_eps, but the number of old active
endpoints supplied to it was always zero, so the number of TTs and the
bandwidth reserved for them was not updated, and could rise
unnecessarily.

This affected systems using Intel's Patherpoint chipset, which rely on
software bandwidth checking.  For example, a Lenovo X230 would lose the
ability to use ports on the docking station after enough suspend/resume
cycles because the bandwidth calculated would rise with every cycle when
a suitable device is attached.

The correct number of active endpoints is calculated in the same way as
in xhci_reserve_bandwidth.

Signed-off-by: Brian Campbell 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: xhci: Bugfix for NULL pointer deference in xhci_endpoint_init() function

2015-08-12T14:33:22+00:00

commit 3496810663922617d4b706ef2780c279252ddd6a upstream.

virt_dev->num_cached_rings counts on freed ring and is not updated
correctly. In xhci_free_or_cache_endpoint_ring() function, the free ring
is added into cache and then num_rings_cache is incremented as below:
		virt_dev->ring_cache[rings_cached] =
			virt_dev->eps[ep_index].ring;
		virt_dev->num_rings_cached++;
here, free ring pointer is added to a current index and then
index is incremented.
So current index always points to empty location in the ring cache.
For getting available free ring, current index should be decremented
first and then corresponding ring buffer value should be taken from ring
cache.

But In function xhci_endpoint_init(), the num_rings_cached index is
accessed before decrement.
		virt_dev->eps[ep_index].new_ring =
			virt_dev->ring_cache[virt_dev->num_rings_cached];
		virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL;
		virt_dev->num_rings_cached--;
This is bug in manipulating the index of ring cache.
And it should be as below:
		virt_dev->num_rings_cached--;
		virt_dev->eps[ep_index].new_ring =
			virt_dev->ring_cache[virt_dev->num_rings_cached];
		virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL;

Signed-off-by: Aman Deep 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

xhci: gracefully handle xhci_irq dead device

2015-08-06T23:32:10+00:00

commit 948fa13504f80b9765d2b753691ab94c83a10341 upstream.

If the xHCI host controller has died (ie, device removed) or suffered
other serious fatal error (STS_FATAL), then xhci_irq should handle this
condition with IRQ_HANDLED instead of -ESHUTDOWN.

Signed-off-by: Joe Lawrence 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

xhci: Solve full event ring by increasing TRBS_PER_SEGMENT to 256

2015-08-06T23:32:10+00:00

commit 18cc2f4cbbaf825a4fedcf2d60fd388d291e0a38 upstream.

Our event ring consists of only one segment, and we risk filling
the event ring in case we get isoc transfers with short intervals
such as webcams that fill a TD every microframe (125us)

With 64 TRB segment size one usb camera could fill the event ring in 8ms.
A setup with several cameras and other devices can fill up the
event ring as it is shared between all devices.
This has occurred when uvcvideo queues 5 * 32TD URBs which then
get cancelled when the video mode changes. The cancelled URBs are returned
in the xhci interrupt context and blocks the interrupt handler from
handling the new events.

A full event ring will block xhci from scheduling traffic and affect all
devices conneted to the xhci, will see errors such as Missed Service
Intervals for isoc devices, and  and Split transaction errors for LS/FS
interrupt devices.

Increasing the TRB_PER_SEGMENT will also increase the default endpoint ring
size, which is welcome as for most isoc transfer we had to dynamically
expand the endpoint ring anyway to be able to queue the 5 * 32TDs uvcvideo
queues.

The default size used to be 64 TRBs per segment

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

xhci: fix isoc endpoint dequeue from advancing too far on transaction error

2015-08-06T23:32:10+00:00

commit d104d0152a97fade389f47635b73a9ccc7295d0b upstream.

Isoc TDs usually consist of one TRB, sometimes two. When all goes well we
receive only one success event for a TD, and move the dequeue pointer to
the next TD.

This fails if the TD consists of two TRBs and we get a transfer error
on the first TRB, we will then see two events for that TD.

Fix this by making sure the event we get is for the last TRB in that TD
before moving the dequeue pointer to the next TD. This will resolve some
of the uvc and dvb issues with the
"ERROR Transfer event TRB DMA ptr not part of current TD" error message

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: xhci: apply XHCI_AVOID_BEI quirk to all Intel xHCI controllers

2015-05-09T22:16:32+00:00

commit 227a4fd801c8a9fa2c4700ab98ec1aec06e3b44d upstream.

When a device with an isochronous endpoint is plugged into the Intel
xHCI host controller, and the driver submits multiple frames per URB,
the xHCI driver will set the Block Event Interrupt (BEI) flag on all
but the last TD for the URB. This causes the host controller to place
an event on the event ring, but not send an interrupt. When the last
TD for the URB completes, BEI is cleared, and we get an interrupt for
the whole URB.

However, under Intel xHCI host controllers, if the event ring is full
of events from transfers with BEI set,  an "Event Ring is Full" event
will be posted to the last entry of the event ring,  but no interrupt
is generated. Host will cease all transfer and command executions and
wait until software completes handling the pending events in the event
ring.  That means xHC stops, but event of "event ring is full" is not
notified. As the result, the xHC looks like dead to user.

This patch is to apply XHCI_AVOID_BEI quirk to Intel xHC devices. And
it should be backported to kernels as old as 3.0, that contains the
commit 69e848c2090a ("Intel xhci: Support EHCI/xHCI port switching.").

Signed-off-by: Lu Baolu 
Tested-by: Alistair Grant 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings

usb: xhci: handle Config Error Change (CEC) in xhci driver

2015-05-09T22:16:32+00:00

commit 9425183d177aa4a2f09d01a74925124f0778b595 upstream.

Linux xHCI driver doesn't report and handle port cofig error change.
If Port Configure Error for root hub port occurs, CEC bit in PORTSC
would be set by xHC and remains 1. This happends when the root port
fails to configure its link partner, e.g. the port fails to exchange
port capabilities information using Port Capability LMPs.

Then the Port Status Change Events will be blocked until all status
change bits(CEC is one of the change bits) are cleared('0') (refer to
xHCI spec 4.19.2). Otherwise, the port status change event for this
root port will not be generated anymore, then root port would look
like dead for user and can't be recovered until a Host Controller
Reset(HCRST).

This patch is to check CEC bit in PORTSC in xhci_get_port_status()
and set a Config Error in the return status if CEC is set. This will
cause a ClearPortFeature request, where CEC bit is cleared in
xhci_clear_port_change_bit().

[The commit log is based on initial Marvell patch posted at
http://marc.info/?l=linux-kernel&m=142323612321434&w=2]

Reported-by: Gregory CLEMENT 
Signed-off-by: Lu Baolu 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2:
 - Fix indentation
 - s/raw_port_status/temp/]
Signed-off-by: Ben Hutchings

xhci: Workaround for PME stuck issues in Intel xhci

2015-05-09T22:16:23+00:00

commit b8cb91e058cd0c0f02059c1207293c5b31d350fa upstream.

The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.

Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks

Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings