linux-stable.git/drivers/usb/host, branch v3.2.53

xhci: Fix spurious wakeups after S5 on Haswell

2013-11-28T14:02:02+00:00

commit 638298dc66ea36623dbc2757a24fc2c4ab41b016 upstream.

Haswell LynxPoint and LynxPoint-LP with the recent Intel BIOS show
mysterious wakeups after shutdown occasionally.  After discussing with
BIOS engineers, they explained that the new BIOS expects that the
wakeup sources are cleared and set to D3 for all wakeup devices when
the system is going to sleep or power off, but the current xhci driver
doesn't do this properly (partly intentionally).

This patch introduces a new quirk, XHCI_SPURIOUS_WAKEUP, for
fixing the spurious wakeups at S5 by calling xhci_reset() in the xhci
shutdown ops as done in xhci_stop(), and setting the device to PCI D3
at shutdown and remove ops.

The PCI D3 call is based on the initial fix patch by Oliver Neukum.

[Note: Sarah changed the quirk name from XHCI_HSW_SPURIOUS_WAKEUP to
XHCI_SPURIOUS_WAKEUP, since none of the other quirks have system names
in them.  Sarah also fixed a collision with a quirk submitted around the
same time, by changing the xhci->quirks bit from 17 to 18.]

This patch should be backported to kernels as old as 3.0, that
contain the commit 1c12443ab8eba71a658fae4572147e56d1f84f66 "xhci: Add
Lynx Point to list of Intel switchable hosts."

Cc: Oliver Neukum 
Signed-off-by: Takashi Iwai 
Signed-off-by: Sarah Sharp 
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings

xhci: quirk for extra long delay for S4

2013-11-28T14:02:02+00:00

commit 455f58925247e8a1a1941e159f3636ad6ee4c90b upstream.

It has been reported that this chipset really cannot
sleep without this extraordinary delay.

This patch should be backported, in order to ensure this host functions
under stable kernels.  The last quirk for Fresco Logic hosts (commit
bba18e33f25072ebf70fd8f7f0cdbf8cdb59a746 "xhci: Extend Fresco Logic MSI
quirk.") was backported to stable kernels as old as 2.6.36.

Signed-off-by: Oliver Neukum 
Signed-off-by: Sarah Sharp 
[bwh: Backported to 3.2:
 - Adjust context
 - Use xhci_dbg() instead of xhci_dbg_trace()]
Signed-off-by: Ben Hutchings

xhci: Don't enable/disable RWE on bus suspend/resume.

2013-11-28T14:02:02+00:00

commit f217c980ca980e3a645b7485ea5eae9a747f4945 upstream.

The RWE bit of the USB 2.0 PORTPMSC register is supposed to enable
remote wakeup for devices in the lower power link state L1.  It has
nothing to do with the device suspend remote wakeup from L2.  The RWE
bit is designed to be set once (when USB 2.0 LPM is enabled for the
port) and cleared only when USB 2.0 LPM is disabled for the port.

The xHCI bus suspend method was setting the RWE bit erroneously, and the
bus resume method was clearing it.  The xHCI 1.0 specification with
errata up to Aug 12, 2012 says in section 4.23.5.1.1.1 "Hardware
Controlled LPM":

"While Hardware USB2 LPM is enabled, software shall not modify the
HIRDBESL or RWE fields of the USB2 PORTPMSC register..."

If we have previously enabled USB 2.0 LPM for a device, that means when
the USB 2.0 bus is resumed, we violate the xHCI specification by
clearing RWE.  It also means that after a bus resume, the host would
think remote wakeup is disabled from L1 for ports with USB 2.0 Link PM
enabled, which is not what we want.

This patch should be backported to kernels as old as 3.2, that
contain the commit 65580b4321eb36f16ae8b5987bfa1bb948fc5112 "xHCI: set
USB2 hardware LPM".  That was the first kernel that supported USB 2.0
Link PM.

Signed-off-by: Sarah Sharp 
[bwh: Backported to 3.2: deleted code was cosmetically different]
Signed-off-by: Ben Hutchings

xhci: Fix race between ep halt and URB cancellation

2013-10-26T20:06:13+00:00

commit 526867c3ca0caa2e3e846cb993b0f961c33c2abb upstream.

The halted state of a endpoint cannot be cleared over CLEAR_HALT from a
user process, because the stopped_td variable was overwritten in the
handle_stopped_endpoint() function. So the xhci_endpoint_reset() function will
refuse the reset and communication with device can not run over this endpoint.
https://bugzilla.kernel.org/show_bug.cgi?id=60699

Signed-off-by: Florian Wolter 
Signed-off-by: Sarah Sharp 
Signed-off-by: Ben Hutchings

USB: fix PM config symbol in uhci-hcd, ehci-hcd, and xhci-hcd

2013-10-26T20:06:06+00:00

commit f875fdbf344b9fde207f66b392c40845dd7e5aa6 upstream.

Since uhci-hcd, ehci-hcd, and xhci-hcd support runtime PM, the .pm
field in their pci_driver structures should be protected by CONFIG_PM
rather than CONFIG_PM_SLEEP.  The corresponding change has already
been made for ohci-hcd.

Without this change, controllers won't do runtime suspend if system
suspend or hibernation isn't enabled.

Signed-off-by: Alan Stern 
CC: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: OHCI: Allow runtime PM without system sleep

2013-10-26T20:06:00+00:00

commit 69820e01aa756b8d228143d997f71523c1e97984 upstream.

Since ohci-hcd supports runtime PM, the .pm field in its pci_driver
structure should be protected by CONFIG_PM rather than
CONFIG_PM_SLEEP.

Without this change, OHCI controllers won't do runtime suspend if
system suspend or hibernation isn't enabled.

Signed-off-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: xhci: Disable runtime PM suspend for quirky controllers

2013-10-26T20:06:00+00:00

commit c8476fb855434c733099079063990e5bfa7ecad6 upstream.

If a USB controller with XHCI_RESET_ON_RESUME goes to runtime suspend,
a reset will be performed upon runtime resume. Any previously suspended
devices attached to the controller will be re-enumerated at this time.
This will cause problems, for example, if an open system call on the
device triggered the resume (the open call will fail).

Note that this change is only relevant when persist_enabled is not set
for USB devices.

This patch should be backported to kernels as old as 3.0, that
contain the commit c877b3b2ad5cb9d4fe523c5496185cc328ff3ae9 "xhci: Add
reset on resume quirk for asrock p67 host".

Signed-off-by: Shawn Nematbakhsh 
Signed-off-by: Sarah Sharp 
Signed-off-by: Ben Hutchings

usb: ehci-mxc: check for pdata before dereferencing

2013-10-26T20:05:59+00:00

commit f375fc520d4df0cd9fcb570f33c103c6c0311f9e upstream.

Commit 7e8d5cd93fac ("USB: Add EHCI support for MX27 and MX31 based
boards") introduced code that could potentially lead to a NULL pointer
dereference on driver removal.

Fix this by checking for the value of pdata before dereferencing it.

Signed-off-by: Daniel Mack 
Reported-by: Dan Carpenter 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings

xhci: fix null pointer dereference on ring_doorbell_for_active_rings

2013-08-02T20:15:09+00:00

commit d66eaf9f89502971fddcb0de550b01fa6f409d83 upstream.

in some cases where device is attched to xhci port and do not responding,
for example ath9k_htc with stalled firmware, kernel will
crash on ring_doorbell_for_active_rings.
This patch check if pointer exist before it is used.

This patch should be backported to kernels as old as 2.6.35, that
contain the commit e9df17eb1408cfafa3d1844bfc7f22c7237b31b8 "USB: xhci:
Correct assumptions about number of rings per endpoint"

Signed-off-by: Oleksij Rempel 
Signed-off-by: Sarah Sharp 
Signed-off-by: Ben Hutchings

usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0

2013-08-02T20:15:08+00:00

commit 07f3cb7c28bf3f4dd80bfb136cf45810c46ac474 upstream.

Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.

Note from Sarah:

The xHCI 1.0 spec changed how hardware handles short packets.  The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set).  On the second successful status, that warning will be
triggered in the driver.

Software is now supposed to not assume the TD is not completed until it
gets that last successful status.  That means we have a slight race
condition, although it should have little practical impact.  This patch
papers over that issue.

It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable.  This
patch is needed for stable to avoid serious log spam.

This patch should be backported to kernels as old as 3.0, that
contain the commit ad808333d8201d53075a11bc8dd83b81f3d68f0b "Intel xhci:
Ignore spurious successful event."

The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.

Signed-off-by: George Cherian 
Signed-off-by: Sarah Sharp 
Signed-off-by: Ben Hutchings