linux-stable.git/drivers/usb/host, branch v3.2.29

xhci: Add Etron XHCI_TRUST_TX_LENGTH quirk.

2012-09-12T02:36:53+00:00

commit 5cb7df2b2d3afee7638b3ef23a5bcb89c6f07bd9 upstream.

Gary reports that with recent kernels, he notices more xHCI driver
warnings:

xhci_hcd 0000:03:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?

We think his Etron xHCI host controller may have the same buggy behavior
as the Fresco Logic xHCI host.  When a short transfer is received, the
host will mark the transfer as successfully completed when it should be
marking it with a short completion.

Fix this by turning on the XHCI_TRUST_TX_LENGTH quirk when the Etron
host is discovered.  Note that Gary has revision 1, but if Etron fixes
this bug in future revisions, the quirk will have no effect.

This patch should be backported to kernels as old as 2.6.36, that
contain a backported version of commit
1530bbc6272d9da1e39ef8e06190d42c13a02733 "xhci: Add new short TX quirk
for Fresco Logic host."

Signed-off-by: Sarah Sharp 
Reported-by: Gary E. Miller 
Signed-off-by: Ben Hutchings

xhci: Increase reset timeout for Renesas 720201 host.

2012-09-12T02:36:52+00:00

commit 22ceac191211cf6688b1bf6ecd93c8b6bf80ed9b upstream.

The NEC/Renesas 720201 xHCI host controller does not complete its reset
within 250 milliseconds.  In fact, it takes about 9 seconds to reset the
host controller, and 1 second for the host to be ready for doorbell
rings.  Extend the reset and CNR polling timeout to 10 seconds each.

This patch should be backported to kernels as old as 2.6.31, that
contain the commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci:
BIOS handoff and HW initialization."

Signed-off-by: Sarah Sharp 
Reported-by: Edwin Klein Mentink 
[bwh: Backported to 3.2: result of second handshake call is returned directly]
Signed-off-by: Ben Hutchings

usb: Add support for root hub port status CAS

2012-07-25T03:11:07+00:00

commit 8bea2bd37df08aaa599aa361a9f8b836ba98e554 upstream.

The host controller port status register supports CAS (Cold Attach
Status) bit. This bit could be set when USB3.0 device is connected
when system is in Sx state. When the system wakes to S0 this port
status with CAS bit is reported and this port can't be used by any
device.

When CAS bit is set the port should be reset by warm reset. This
was not supported by xhci driver.

The issue was found when pendrive was connected to suspended
platform. The link state of "Compliance Mode" was reported together
with CAS bit. This link state was also not supported by xhci and
core/hub.c.

The CAS bit is defined only for xhci root hub port and it is
not supported on regular hubs. The link status is used to force
warm reset on port. Make the USB core issue a warm reset when port
is in ether the 'inactive' or 'compliance mode'. Change the xHCI driver
to report 'compliance mode' when the CAS is set. This force warm reset
on the root hub port.

This patch should be backported to stable kernels as old as 3.2, that
contain the commit 10d674a82e553cb8a1f41027bb3c3e309b3f6804 "USB: When
hot reset for USB3 fails, try warm reset."

Signed-off-by: Stanislaw Ledwon 
Signed-off-by: Sarah Sharp 
Acked-by: Andiry Xu 
Signed-off-by: Ben Hutchings

USB: fix PS3 EHCI systems

2012-06-19T22:18:27+00:00

commit 4f7a67e2dd49fbfba002c453bc24bf00e701cc71 upstream.

After commit aaa0ef289afe9186f81e2340114ea413eef0492a "PS3 EHCI QH
read work-around", Terratec Grabby (em28xx) stopped working with AMD
Geode LX 800 (USB controller AMD CS5536). Since this is a PS3 only
fix, the following patch adds a conditional block around it.

Signed-off-by: Ricardo Martins 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: PS3 EHCI QH read work-around

2012-06-19T22:18:27+00:00

commit aaa0ef289afe9186f81e2340114ea413eef0492a upstream.

PS3 EHCI HC errata fix 244.  The SCC EHCI HC will not correctly perform QH
reads that occur near or span a micro-frame boundry.  This is due to a problem
in the Nak Count Reload Control logic (EHCI Specification 1.0 Section 4.9.1).

The work-around for this problem is for the HC driver to set I=1 (inactive) for
QHs with H=1 (list head).

Signed-off-by: Geoff Levand 
Acked-by: Alan Stern 
Signed-off-by: Ben Hutchings

xHCI: Increase the timeout for controller save/restore state operation

2012-06-19T22:18:26+00:00

commit 622eb783fe6ff4c1baa47db16c3a5db97f9e6e50 upstream.

When system software decides to power down the xHC with the intent of
resuming operation at a later time, it will ask xHC to save the internal
state and restore it when resume to correctly recover from a power event.
Two bits are used to enable this operation: Save State and Restore State.

xHCI spec 4.23.2 says software should "Set the Controller Save/Restore
State flag in the USBCMD register and wait for the Save/Restore State
Status flag in the USBSTS register to transition to '0'". However, it does
not define how long software should wait for the SSS/RSS bit to transition
to 0.

Currently the timeout is set to 1ms. There is bug report
(https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1002697)
indicates that the timeout is too short for ASMedia ASM1042 host controller
to save/restore the state successfully. Increase the timeout to 10ms helps to
resolve the issue.

This patch should be backported to stable kernels as old as 2.6.37, that
contain the commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI:
PCI power management implementation"

Signed-off-by: Andiry Xu 
Signed-off-by: Sarah Sharp 
Cc: Ming Lei 
Signed-off-by: Ben Hutchings

xhci: Don't free endpoints in xhci_mem_cleanup()

2012-06-19T22:18:26+00:00

commit 32f1d2c536d0c26c5814cb0e6a0606c42d02fac1 upstream.

This patch fixes a few issues introduced in the recent fix
[f8a9e72d: USB: fix resource leak in xhci power loss path]

- The endpoints listed in bw table are just links and each entry is an
 array member of dev->eps[].  But the commit above adds a kfree() call
 to these instances, and thus it results in memory corruption.

- It clears only the first entry of rh_bw[], but there can be multiple
  ports.

- It'd be safer to clear the list_head of ep as well, not only
  removing from the list, as it's checked in
  xhci_discover_or_reset_device().

This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe "xhci: Store
information about roothubs and TTs."

Signed-off-by: Takashi Iwai 
Signed-off-by: Sarah Sharp 
Reviewed-by: Oliver Neukum 
Signed-off-by: Ben Hutchings

xhci: Fix invalid loop check in xhci_free_tt_info()

2012-06-19T22:18:25+00:00

commit 46ed8f00d8982e49f8fe2c1a9cea192f640cb3ba upstream.

xhci_free_tt_info() may access the invalid memory when it removes the
last entry but the list is not empty.  Then tt_next reaches to the
list head but it still tries to check the tt_info of that entry.

This patch fixes the bug and cleans up the messy code by rewriting
with a simple list_for_each_entry_safe().

This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe "xhci: Store
information about roothubs and TTs."

Signed-off-by: Takashi Iwai 
Signed-off-by: Sarah Sharp 
Reviewed-by: Oliver Neukum 
Signed-off-by: Ben Hutchings

USB: add NO_D3_DURING_SLEEP flag and revert 151b61284776be2

2012-06-19T22:18:25+00:00

commit c2fb8a3fa25513de8fedb38509b1f15a5bbee47b upstream.

This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

A similar patch has already been applied as commit
151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during
suspend on ASUS computers).  The patch supersedes that one and reverts
it.  There are two differences:

	The old patch added the flag at the USB level; this patch
	adds it at the PCI level.

	The old patch applied to all chipsets with the same vendor,
	subsystem vendor, and product IDs; this patch makes an
	exception for a known-good system (based on DMI information).

Signed-off-by: Alan Stern 
Tested-by: Dâniel Fraga 
Tested-by: Andrey Rahmatullin 
Tested-by: Steven Rostedt 
Reviewed-by: Rafael J. Wysocki 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

xhci: Reset reserved command ring TRBs on cleanup.

2012-05-30T23:43:45+00:00

commit 33b2831ac870d50cc8e01c317b07fb1e69c13fe1 upstream.

When the xHCI driver needs to clean up memory (perhaps due to a failed
register restore on resume from S3 or resume from S4), it needs to reset
the number of reserved TRBs on the command ring to zero.  Otherwise,
several resume cycles (about 30) with a UAS device attached will
continually increment the number of reserved TRBs, until all command
submissions fail because there isn't enough room on the command ring.

This patch should be backported to kernels as old as 2.6.32,
that contain the commit 913a8a344ffcaf0b4a586d6662a2c66a7106557d
"USB: xhci: Change how xHCI commands are handled."

Signed-off-by: Sarah Sharp 
Signed-off-by: Ben Hutchings