linux-stable.git/drivers/usb/host, branch v3.16.78 Linux kernel stable tree usb: host: ohci: fix a race condition between shutdown and irq 2019-11-22T15:57:22+00:00 Yoshihiro Shimoda yoshihiro.shimoda.uh@renesas.com 2019-08-27T03:51:50+00:00 b45a88d1816dd13a879b5bd0bf360394382e041f commit a349b95d7ca0cea71be4a7dac29830703de7eb62 upstream. This patch fixes an issue that the following error is possible to happen when ohci hardware causes an interruption and the system is shutting down at the same time. [ 34.851754] usb 2-1: USB disconnect, device number 2 [ 35.166658] irq 156: nobody cared (try booting with the "irqpoll" option) [ 35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85 [ 35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) [ 35.187886] Workqueue: usb_hub_wq hub_event [ 35.192063] Call trace: [ 35.194509] dump_backtrace+0x0/0x150 [ 35.198165] show_stack+0x14/0x20 [ 35.201475] dump_stack+0xa0/0xc4 [ 35.204785] __report_bad_irq+0x34/0xe8 [ 35.208614] note_interrupt+0x2cc/0x318 [ 35.212446] handle_irq_event_percpu+0x5c/0x88 [ 35.216883] handle_irq_event+0x48/0x78 [ 35.220712] handle_fasteoi_irq+0xb4/0x188 [ 35.224802] generic_handle_irq+0x24/0x38 [ 35.228804] __handle_domain_irq+0x5c/0xb0 [ 35.232893] gic_handle_irq+0x58/0xa8 [ 35.236548] el1_irq+0xb8/0x180 [ 35.239681] __do_softirq+0x94/0x23c [ 35.243253] irq_exit+0xd0/0xd8 [ 35.246387] __handle_domain_irq+0x60/0xb0 [ 35.250475] gic_handle_irq+0x58/0xa8 [ 35.254130] el1_irq+0xb8/0x180 [ 35.257268] kernfs_find_ns+0x5c/0x120 [ 35.261010] kernfs_find_and_get_ns+0x3c/0x60 [ 35.265361] sysfs_unmerge_group+0x20/0x68 [ 35.269454] dpm_sysfs_remove+0x2c/0x68 [ 35.273284] device_del+0x80/0x370 [ 35.276683] hid_destroy_device+0x28/0x60 [ 35.280686] usbhid_disconnect+0x4c/0x80 [ 35.284602] usb_unbind_interface+0x6c/0x268 [ 35.288867] device_release_driver_internal+0xe4/0x1b0 [ 35.293998] device_release_driver+0x14/0x20 [ 35.298261] bus_remove_device+0x110/0x128 [ 35.302350] device_del+0x148/0x370 [ 35.305832] usb_disable_device+0x8c/0x1d0 [ 35.309921] usb_disconnect+0xc8/0x2d0 [ 35.313663] hub_event+0x6e0/0x1128 [ 35.317146] process_one_work+0x1e0/0x320 [ 35.321148] worker_thread+0x40/0x450 [ 35.324805] kthread+0x124/0x128 [ 35.328027] ret_from_fork+0x10/0x18 [ 35.331594] handlers: [ 35.333862] [<0000000079300c1d>] usb_hcd_irq [ 35.338126] [<0000000079300c1d>] usb_hcd_irq [ 35.342389] Disabling IRQ #156 ohci_shutdown() disables all the interrupt and rh_state is set to OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF is possible to be set by start_ed_unlink() which is called: ohci_irq() -> process_done_list() -> takeback_td() -> start_ed_unlink() So, ohci_irq() has the following condition, the issue happens by &ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and ohci->rh_state = OHCI_RH_HALTED: /* interrupt for some other device? */ if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED)) return IRQ_NOTMINE; To fix the issue, ohci_shutdown() holds the spin lock while disabling the interruption and changing the rh_state flag to prevent reenable the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also calls the ohci_shutdown() and it already held the spin lock, so that the patch makes a new function as _ohci_shutdown(). This patch is inspired by a Renesas R-Car Gen3 BSP patch from Tho Vu. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: - Drop change in io_watchdog_func() - Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit a349b95d7ca0cea71be4a7dac29830703de7eb62 upstream.

This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.

[   34.851754] usb 2-1: USB disconnect, device number 2
[   35.166658] irq 156: nobody cared (try booting with the "irqpoll" option)
[   35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85
[   35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[   35.187886] Workqueue: usb_hub_wq hub_event
[   35.192063] Call trace:
[   35.194509]  dump_backtrace+0x0/0x150
[   35.198165]  show_stack+0x14/0x20
[   35.201475]  dump_stack+0xa0/0xc4
[   35.204785]  __report_bad_irq+0x34/0xe8
[   35.208614]  note_interrupt+0x2cc/0x318
[   35.212446]  handle_irq_event_percpu+0x5c/0x88
[   35.216883]  handle_irq_event+0x48/0x78
[   35.220712]  handle_fasteoi_irq+0xb4/0x188
[   35.224802]  generic_handle_irq+0x24/0x38
[   35.228804]  __handle_domain_irq+0x5c/0xb0
[   35.232893]  gic_handle_irq+0x58/0xa8
[   35.236548]  el1_irq+0xb8/0x180
[   35.239681]  __do_softirq+0x94/0x23c
[   35.243253]  irq_exit+0xd0/0xd8
[   35.246387]  __handle_domain_irq+0x60/0xb0
[   35.250475]  gic_handle_irq+0x58/0xa8
[   35.254130]  el1_irq+0xb8/0x180
[   35.257268]  kernfs_find_ns+0x5c/0x120
[   35.261010]  kernfs_find_and_get_ns+0x3c/0x60
[   35.265361]  sysfs_unmerge_group+0x20/0x68
[   35.269454]  dpm_sysfs_remove+0x2c/0x68
[   35.273284]  device_del+0x80/0x370
[   35.276683]  hid_destroy_device+0x28/0x60
[   35.280686]  usbhid_disconnect+0x4c/0x80
[   35.284602]  usb_unbind_interface+0x6c/0x268
[   35.288867]  device_release_driver_internal+0xe4/0x1b0
[   35.293998]  device_release_driver+0x14/0x20
[   35.298261]  bus_remove_device+0x110/0x128
[   35.302350]  device_del+0x148/0x370
[   35.305832]  usb_disable_device+0x8c/0x1d0
[   35.309921]  usb_disconnect+0xc8/0x2d0
[   35.313663]  hub_event+0x6e0/0x1128
[   35.317146]  process_one_work+0x1e0/0x320
[   35.321148]  worker_thread+0x40/0x450
[   35.324805]  kthread+0x124/0x128
[   35.328027]  ret_from_fork+0x10/0x18
[   35.331594] handlers:
[   35.333862] [<0000000079300c1d>] usb_hcd_irq
[   35.338126] [<0000000079300c1d>] usb_hcd_irq
[   35.342389] Disabling IRQ #156

ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
 ohci_irq()
  -> process_done_list()
   -> takeback_td()
    -> start_ed_unlink()

So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:

	/* interrupt for some other device? */
	if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
		return IRQ_NOTMINE;

To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().

This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
 - Drop change in io_watchdog_func()
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: wusbcore: fix unbalanced get/put cluster_id 2019-11-22T15:57:05+00:00 Phong Tran tranmanphong@gmail.com 2019-07-24T02:06:01+00:00 87df15bad1762699a4fe808a8567ce18a4293e51 commit f90bf1ece48a736097ea224430578fe586a9544c upstream. syzboot reported that https://syzkaller.appspot.com/bug?extid=fd2bd7df88c606eea4ef There is not consitency parameter in cluste_id_get/put calling. In case of getting the id with result is failure, the wusbhc->cluster_id will not be updated and this can not be used for wusb_cluster_id_put(). Tested report https://groups.google.com/d/msg/syzkaller-bugs/0znZopp3-9k/oxOrhLkLEgAJ Reproduce and gdb got the details: 139 addr = wusb_cluster_id_get(); (gdb) n 140 if (addr == 0) (gdb) print addr $1 = 254 '\376' (gdb) n 142 result = __hwahc_set_cluster_id(hwahc, addr); (gdb) print result $2 = -71 (gdb) break wusb_cluster_id_put Breakpoint 3 at 0xffffffff836e3f20: file drivers/usb/wusbcore/wusbhc.c, line 384. (gdb) s Thread 2 hit Breakpoint 3, wusb_cluster_id_put (id=0 '\000') at drivers/usb/wusbcore/wusbhc.c:384 384 id = 0xff - id; (gdb) n 385 BUG_ON(id >= CLUSTER_IDS); (gdb) print id $3 = 255 '\377' Reported-by: syzbot+fd2bd7df88c606eea4ef@syzkaller.appspotmail.com Signed-off-by: Phong Tran <tranmanphong@gmail.com> Link: https://lore.kernel.org/r/20190724020601.15257-1-tranmanphong@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit f90bf1ece48a736097ea224430578fe586a9544c upstream.

syzboot reported that
https://syzkaller.appspot.com/bug?extid=fd2bd7df88c606eea4ef

There is not consitency parameter in cluste_id_get/put calling.
In case of getting the id with result is failure, the wusbhc->cluster_id
will not be updated and this can not be used for wusb_cluster_id_put().

Tested report
https://groups.google.com/d/msg/syzkaller-bugs/0znZopp3-9k/oxOrhLkLEgAJ

Reproduce and gdb got the details:

139		addr = wusb_cluster_id_get();
(gdb) n
140		if (addr == 0)
(gdb) print addr
$1 = 254 '\376'
(gdb) n
142		result = __hwahc_set_cluster_id(hwahc, addr);
(gdb) print result
$2 = -71
(gdb) break wusb_cluster_id_put
Breakpoint 3 at 0xffffffff836e3f20: file drivers/usb/wusbcore/wusbhc.c, line 384.
(gdb) s
Thread 2 hit Breakpoint 3, wusb_cluster_id_put (id=0 '\000') at drivers/usb/wusbcore/wusbhc.c:384
384		id = 0xff - id;
(gdb) n
385		BUG_ON(id >= CLUSTER_IDS);
(gdb) print id
$3 = 255 '\377'

Reported-by: syzbot+fd2bd7df88c606eea4ef@syzkaller.appspotmail.com
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Link: https://lore.kernel.org/r/20190724020601.15257-1-tranmanphong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: pci-quirks: Correct AMD PLL quirk detection 2019-11-22T15:57:05+00:00 Ryan Kennedy ryan5544@gmail.com 2019-07-04T15:35:28+00:00 21025698e354e52cf73bf1a3840c0d86387da702 commit f3dccdaade4118070a3a47bef6b18321431f9ac6 upstream. The AMD PLL USB quirk is incorrectly enabled on newer Ryzen chipsets. The logic in usb_amd_find_chipset_info currently checks for unaffected chipsets rather than affected ones. This broke once a new chipset was added in e788787ef. It makes more sense to reverse the logic so it won't need to be updated as new chipsets are added. Note that the core of the workaround in usb_amd_quirk_pll does correctly check the chipset. Signed-off-by: Ryan Kennedy <ryan5544@gmail.com> Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume") Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20190704153529.9429-2-ryan5544@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit f3dccdaade4118070a3a47bef6b18321431f9ac6 upstream.

The AMD PLL USB quirk is incorrectly enabled on newer Ryzen
chipsets. The logic in usb_amd_find_chipset_info currently checks
for unaffected chipsets rather than affected ones. This broke
once a new chipset was added in e788787ef. It makes more sense
to reverse the logic so it won't need to be updated as new
chipsets are added. Note that the core of the workaround in
usb_amd_quirk_pll does correctly check the chipset.

Signed-off-by: Ryan Kennedy <ryan5544@gmail.com>
Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190704153529.9429-2-ryan5544@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: xhci: avoid null pointer deref when bos field is NULL 2019-10-05T15:19:42+00:00 Carsten Schmid carsten_schmid@mentor.com 2019-05-22T11:33:59+00:00 9b86a2218f77fe7e0661f920f037ac4103fa3904 commit 7aa1bb2ffd84d6b9b5f546b079bb15cd0ab6e76e upstream. With defective USB sticks we see the following error happen: usb 1-3: new high-speed USB device number 6 using xhci_hcd usb 1-3: device descriptor read/64, error -71 usb 1-3: device descriptor read/64, error -71 usb 1-3: new high-speed USB device number 7 using xhci_hcd usb 1-3: device descriptor read/64, error -71 usb 1-3: unable to get BOS descriptor set usb 1-3: New USB device found, idVendor=0781, idProduct=5581 usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 ... BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 This comes from the following place: [ 1660.215380] IP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] [ 1660.222092] PGD 0 P4D 0 [ 1660.224918] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 1660.425520] CPU: 1 PID: 38 Comm: kworker/1:1 Tainted: P U W O 4.14.67-apl #1 [ 1660.434277] Workqueue: usb_hub_wq hub_event [usbcore] [ 1660.439918] task: ffffa295b6ae4c80 task.stack: ffffad4580150000 [ 1660.446532] RIP: 0010:xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] [ 1660.453821] RSP: 0018:ffffad4580153c70 EFLAGS: 00010046 [ 1660.459655] RAX: 0000000000000000 RBX: ffffa295b4d7c000 RCX: 0000000000000002 [ 1660.467625] RDX: 0000000000000002 RSI: ffffffff984a55b2 RDI: ffffffff984a55b2 [ 1660.475586] RBP: ffffad4580153cc8 R08: 0000000000d6520a R09: 0000000000000001 [ 1660.483556] R10: ffffad4580a004a0 R11: 0000000000000286 R12: ffffa295b4d7c000 [ 1660.491525] R13: 0000000000010648 R14: ffffa295a84e1800 R15: 0000000000000000 [ 1660.499494] FS: 0000000000000000(0000) GS:ffffa295bfc80000(0000) knlGS:0000000000000000 [ 1660.508530] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1660.514947] CR2: 0000000000000008 CR3: 000000025a114000 CR4: 00000000003406a0 [ 1660.522917] Call Trace: [ 1660.525657] usb_set_usb2_hardware_lpm+0x3d/0x70 [usbcore] [ 1660.531792] usb_disable_device+0x242/0x260 [usbcore] [ 1660.537439] usb_disconnect+0xc1/0x2b0 [usbcore] [ 1660.542600] hub_event+0x596/0x18f0 [usbcore] [ 1660.547467] ? trace_preempt_on+0xdf/0x100 [ 1660.552040] ? process_one_work+0x1c1/0x410 [ 1660.556708] process_one_work+0x1d2/0x410 [ 1660.561184] ? preempt_count_add.part.3+0x21/0x60 [ 1660.566436] worker_thread+0x2d/0x3f0 [ 1660.570522] kthread+0x122/0x140 [ 1660.574123] ? process_one_work+0x410/0x410 [ 1660.578792] ? kthread_create_on_node+0x60/0x60 [ 1660.583849] ret_from_fork+0x3a/0x50 [ 1660.587839] Code: 00 49 89 c3 49 8b 84 24 50 16 00 00 8d 4a ff 48 8d 04 c8 48 89 ca 4c 8b 10 45 8b 6a 04 48 8b 00 48 89 45 c0 49 8b 86 80 03 00 00 <48> 8b 40 08 8b 40 03 0f 1f 44 00 00 45 85 ff 0f 84 81 01 00 00 [ 1660.608980] RIP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] RSP: ffffad4580153c70 [ 1660.617921] CR2: 0000000000000008 Tracking this down shows that udev->bos is NULL in the following code: (xhci.c, in xhci_set_usb2_hardware_lpm) field = le32_to_cpu(udev->bos->ext_cap->bmAttributes); <<<<<<< here xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n", enable ? "enable" : "disable", port_num + 1); if (enable) { /* Host supports BESL timeout instead of HIRD */ if (udev->usb2_hw_lpm_besl_capable) { /* if device doesn't have a preferred BESL value use a * default one which works with mixed HIRD and BESL * systems. See XHCI_DEFAULT_BESL definition in xhci.h */ if ((field & USB_BESL_SUPPORT) && (field & USB_BESL_BASELINE_VALID)) hird = USB_GET_BESL_BASELINE(field); else hird = udev->l1_params.besl; The failing case is when disabling LPM. So it is sufficient to avoid access to udev->bos by moving the instruction into the "enable" clause. Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 7aa1bb2ffd84d6b9b5f546b079bb15cd0ab6e76e upstream.

With defective USB sticks we see the following error happen:
usb 1-3: new high-speed USB device number 6 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: device descriptor read/64, error -71
usb 1-3: new high-speed USB device number 7 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: unable to get BOS descriptor set
usb 1-3: New USB device found, idVendor=0781, idProduct=5581
usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
...
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008

This comes from the following place:
[ 1660.215380] IP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd]
[ 1660.222092] PGD 0 P4D 0
[ 1660.224918] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 1660.425520] CPU: 1 PID: 38 Comm: kworker/1:1 Tainted: P     U  W  O    4.14.67-apl #1
[ 1660.434277] Workqueue: usb_hub_wq hub_event [usbcore]
[ 1660.439918] task: ffffa295b6ae4c80 task.stack: ffffad4580150000
[ 1660.446532] RIP: 0010:xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd]
[ 1660.453821] RSP: 0018:ffffad4580153c70 EFLAGS: 00010046
[ 1660.459655] RAX: 0000000000000000 RBX: ffffa295b4d7c000 RCX: 0000000000000002
[ 1660.467625] RDX: 0000000000000002 RSI: ffffffff984a55b2 RDI: ffffffff984a55b2
[ 1660.475586] RBP: ffffad4580153cc8 R08: 0000000000d6520a R09: 0000000000000001
[ 1660.483556] R10: ffffad4580a004a0 R11: 0000000000000286 R12: ffffa295b4d7c000
[ 1660.491525] R13: 0000000000010648 R14: ffffa295a84e1800 R15: 0000000000000000
[ 1660.499494] FS:  0000000000000000(0000) GS:ffffa295bfc80000(0000) knlGS:0000000000000000
[ 1660.508530] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1660.514947] CR2: 0000000000000008 CR3: 000000025a114000 CR4: 00000000003406a0
[ 1660.522917] Call Trace:
[ 1660.525657]  usb_set_usb2_hardware_lpm+0x3d/0x70 [usbcore]
[ 1660.531792]  usb_disable_device+0x242/0x260 [usbcore]
[ 1660.537439]  usb_disconnect+0xc1/0x2b0 [usbcore]
[ 1660.542600]  hub_event+0x596/0x18f0 [usbcore]
[ 1660.547467]  ? trace_preempt_on+0xdf/0x100
[ 1660.552040]  ? process_one_work+0x1c1/0x410
[ 1660.556708]  process_one_work+0x1d2/0x410
[ 1660.561184]  ? preempt_count_add.part.3+0x21/0x60
[ 1660.566436]  worker_thread+0x2d/0x3f0
[ 1660.570522]  kthread+0x122/0x140
[ 1660.574123]  ? process_one_work+0x410/0x410
[ 1660.578792]  ? kthread_create_on_node+0x60/0x60
[ 1660.583849]  ret_from_fork+0x3a/0x50
[ 1660.587839] Code: 00 49 89 c3 49 8b 84 24 50 16 00 00 8d 4a ff 48 8d 04 c8 48 89 ca 4c 8b 10 45 8b 6a 04 48 8b 00 48 89 45 c0 49 8b 86 80 03 00 00 <48> 8b 40 08 8b 40 03 0f 1f 44 00 00 45 85 ff 0f 84 81 01 00 00
[ 1660.608980] RIP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] RSP: ffffad4580153c70
[ 1660.617921] CR2: 0000000000000008

Tracking this down shows that udev->bos is NULL in the following code:
(xhci.c, in xhci_set_usb2_hardware_lpm)
	field = le32_to_cpu(udev->bos->ext_cap->bmAttributes);  <<<<<<< here

	xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n",
			enable ? "enable" : "disable", port_num + 1);

	if (enable) {
		/* Host supports BESL timeout instead of HIRD */
		if (udev->usb2_hw_lpm_besl_capable) {
			/* if device doesn't have a preferred BESL value use a
			 * default one which works with mixed HIRD and BESL
			 * systems. See XHCI_DEFAULT_BESL definition in xhci.h
			 */
			if ((field & USB_BESL_SUPPORT) &&
			    (field & USB_BESL_BASELINE_VALID))
				hird = USB_GET_BESL_BASELINE(field);
			else
				hird = udev->l1_params.besl;

The failing case is when disabling LPM. So it is sufficient to avoid
access to udev->bos by moving the instruction into the "enable" clause.

Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: Don't let USB3 ports stuck in polling state prevent suspend 2019-08-13T11:38:52+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2019-03-22T15:50:17+00:00 a3a3b6c71ed63aa3e6dc56b1922d273a77585cb1 commit d92f2c59cc2cbca6bfb2cc54882b58ba76b15fd4 upstream. Commit 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") was intended to prevent ports that were still link training from being forced to U3 suspend state mid enumeration. This solved enumeration issues for devices with slow link training. Turns out some devices are stuck in the link training/polling state, and thus that patch will prevent suspend completely for these devices. This is seen with USB3 card readers in some MacBooks. Instead of preventing suspend, give some time to complete the link training. On successful training the port will end up as connected and enabled. If port instead is stuck in link training the bus suspend will continue suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout). Original patch was sent to stable, this one should go there as well Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit d92f2c59cc2cbca6bfb2cc54882b58ba76b15fd4 upstream.

Commit 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.

Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.

Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).

Original patch was sent to stable, this one should go there as well

Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: r8a66597: Fix a possible concurrency use-after-free bug in r8a66597_endpoint_disable() 2019-04-04T15:13:58+00:00 Jia-Ju Bai baijiaju1990@gmail.com 2018-12-18T12:04:25+00:00 77937a5d84a309e4fbaa0b197cb60f138101a3c3 commit c85400f886e3d41e69966470879f635a2b50084c upstream. The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may be concurrently executed. The two functions both access a possible shared variable "hep->hcpriv". This shared variable is freed by r8a66597_endpoint_disable() via the call path: r8a66597_endpoint_disable kfree(hep->hcpriv) (line 1995 in Linux-4.19) This variable is read by r8a66597_urb_enqueue() via the call path: r8a66597_urb_enqueue spin_lock_irqsave(&r8a66597->lock) init_pipe_info enable_r8a66597_pipe pipe = hep->hcpriv (line 802 in Linux-4.19) The read operation is protected by a spinlock, but the free operation is not protected by this spinlock, thus a concurrency use-after-free bug may occur. To fix this bug, the spin-lock and spin-unlock function calls in r8a66597_endpoint_disable() are moved to protect the free operation. Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit c85400f886e3d41e69966470879f635a2b50084c upstream.

The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may
be concurrently executed.
The two functions both access a possible shared variable "hep->hcpriv".

This shared variable is freed by r8a66597_endpoint_disable() via the
call path:
r8a66597_endpoint_disable
  kfree(hep->hcpriv) (line 1995 in Linux-4.19)

This variable is read by r8a66597_urb_enqueue() via the call path:
r8a66597_urb_enqueue
  spin_lock_irqsave(&r8a66597->lock)
  init_pipe_info
    enable_r8a66597_pipe
      pipe = hep->hcpriv (line 802 in Linux-4.19)

The read operation is protected by a spinlock, but the free operation
is not protected by this spinlock, thus a concurrency use-after-free bug
may occur.

To fix this bug, the spin-lock and spin-unlock function calls in
r8a66597_endpoint_disable() are moved to protect the free operation.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: Don't prevent USB2 bus suspend in state check intended for USB3 only 2019-02-11T17:54:26+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2018-12-14T08:54:43+00:00 c6ebef26a95834d86a9e72fa70f5fd4b6ec395bf commit 45f750c16cae3625014c14c77bd9005eda975d35 upstream. The code to prevent a bus suspend if a USB3 port was still in link training also reacted to USB2 port polling state. This caused bus suspend to busyloop in some cases. USB2 polling state is different from USB3, and should not prevent bus suspend. Limit the USB3 link training state check to USB3 root hub ports only. The origial commit went to stable so this need to be applied there as well Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 45f750c16cae3625014c14c77bd9005eda975d35 upstream.

The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.

Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well

Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: Prevent U1/U2 link pm states if exit latency is too long 2019-02-11T17:54:21+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2018-12-05T12:22:39+00:00 7e2344d2f1e9a91f8baa84d62a32ea442f87d8c6 commit 0472bf06c6fd33c1a18aaead4c8f91e5a03d8d7b upstream. Don't allow USB3 U1 or U2 if the latency to wake up from the U-state reaches the service interval for a periodic endpoint. This is according to xhci 1.1 specification section 4.23.5.2 extra note: "Software shall ensure that a device is prevented from entering a U-state where its worst case exit latency approaches the ESIT." Allowing too long exit latencies for periodic endpoint confuses xHC internal scheduling, and new devices may fail to enumerate with a "Not enough bandwidth for new device state" error from the host. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: adjust context, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 0472bf06c6fd33c1a18aaead4c8f91e5a03d8d7b upstream.

Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.

This is according to xhci 1.1 specification section 4.23.5.2 extra note:

"Software shall ensure that a device is prevented from entering a U-state
 where its worst case exit latency approaches the ESIT."

Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: workaround CSS timeout on AMD SNPS 3.0 xHC 2019-02-11T17:54:21+00:00 Sandeep Singh sandeep.singh@amd.com 2018-12-05T12:22:38+00:00 f6b0a0659bdaa814ca0ed5c433cb26e417260408 commit a7d57abcc8a5bdeb53bbf8e87558e8e0a2c2a29d upstream. Occasionally AMD SNPS 3.0 xHC does not respond to CSS when set, also it does not flag anything on SRE and HCE to point the internal xHC errors on USBSTS register. This stalls the entire system wide suspend and there is no point in stalling just because of xHC CSS is not responding. To work around this problem, if the xHC does not flag anything on SRE and HCE, we can skip the CSS timeout and allow the system to continue the suspend. Once the system resume happens we can internally reset the controller using XHCI_RESET_ON_RESUME quirk Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com> cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: - Use next available quirk bit - Fold in commit 2419f30a4a4f "USB: xhci: fix 'broken_suspend' placement ..." - Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit a7d57abcc8a5bdeb53bbf8e87558e8e0a2c2a29d upstream.

Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.

To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk

Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
 - Use next available quirk bit
 - Fold in commit 2419f30a4a4f "USB: xhci: fix 'broken_suspend' placement ..."
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: check usb_get_extra_descriptor for proper size 2019-02-11T17:54:20+00:00 Mathias Payer mathias.payer@nebelwelt.net 2018-12-05T20:19:59+00:00 f8860a91d7538022c1c3f0bdddeec9a9d83e0c09 commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream. When reading an extra descriptor, we need to properly check the minimum and maximum size allowed, to prevent from invalid data being sent by a device. Reported-by: Hui Peng <benquike@gmail.com> Reported-by: Mathias Payer <mathias.payer@nebelwelt.net> Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Hui Peng <benquike@gmail.com> Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream.

When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.

Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>