linux-stable.git/drivers/usb/host, branch v3.16.76

usb: xhci: avoid null pointer deref when bos field is NULL

2019-10-05T15:19:42+00:00

commit 7aa1bb2ffd84d6b9b5f546b079bb15cd0ab6e76e upstream.

With defective USB sticks we see the following error happen:
usb 1-3: new high-speed USB device number 6 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: device descriptor read/64, error -71
usb 1-3: new high-speed USB device number 7 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: unable to get BOS descriptor set
usb 1-3: New USB device found, idVendor=0781, idProduct=5581
usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
...
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008

This comes from the following place:
[ 1660.215380] IP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd]
[ 1660.222092] PGD 0 P4D 0
[ 1660.224918] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 1660.425520] CPU: 1 PID: 38 Comm: kworker/1:1 Tainted: P     U  W  O    4.14.67-apl #1
[ 1660.434277] Workqueue: usb_hub_wq hub_event [usbcore]
[ 1660.439918] task: ffffa295b6ae4c80 task.stack: ffffad4580150000
[ 1660.446532] RIP: 0010:xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd]
[ 1660.453821] RSP: 0018:ffffad4580153c70 EFLAGS: 00010046
[ 1660.459655] RAX: 0000000000000000 RBX: ffffa295b4d7c000 RCX: 0000000000000002
[ 1660.467625] RDX: 0000000000000002 RSI: ffffffff984a55b2 RDI: ffffffff984a55b2
[ 1660.475586] RBP: ffffad4580153cc8 R08: 0000000000d6520a R09: 0000000000000001
[ 1660.483556] R10: ffffad4580a004a0 R11: 0000000000000286 R12: ffffa295b4d7c000
[ 1660.491525] R13: 0000000000010648 R14: ffffa295a84e1800 R15: 0000000000000000
[ 1660.499494] FS:  0000000000000000(0000) GS:ffffa295bfc80000(0000) knlGS:0000000000000000
[ 1660.508530] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1660.514947] CR2: 0000000000000008 CR3: 000000025a114000 CR4: 00000000003406a0
[ 1660.522917] Call Trace:
[ 1660.525657]  usb_set_usb2_hardware_lpm+0x3d/0x70 [usbcore]
[ 1660.531792]  usb_disable_device+0x242/0x260 [usbcore]
[ 1660.537439]  usb_disconnect+0xc1/0x2b0 [usbcore]
[ 1660.542600]  hub_event+0x596/0x18f0 [usbcore]
[ 1660.547467]  ? trace_preempt_on+0xdf/0x100
[ 1660.552040]  ? process_one_work+0x1c1/0x410
[ 1660.556708]  process_one_work+0x1d2/0x410
[ 1660.561184]  ? preempt_count_add.part.3+0x21/0x60
[ 1660.566436]  worker_thread+0x2d/0x3f0
[ 1660.570522]  kthread+0x122/0x140
[ 1660.574123]  ? process_one_work+0x410/0x410
[ 1660.578792]  ? kthread_create_on_node+0x60/0x60
[ 1660.583849]  ret_from_fork+0x3a/0x50
[ 1660.587839] Code: 00 49 89 c3 49 8b 84 24 50 16 00 00 8d 4a ff 48 8d 04 c8 48 89 ca 4c 8b 10 45 8b 6a 04 48 8b 00 48 89 45 c0 49 8b 86 80 03 00 00 <48> 8b 40 08 8b 40 03 0f 1f 44 00 00 45 85 ff 0f 84 81 01 00 00
[ 1660.608980] RIP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] RSP: ffffad4580153c70
[ 1660.617921] CR2: 0000000000000008

Tracking this down shows that udev->bos is NULL in the following code:
(xhci.c, in xhci_set_usb2_hardware_lpm)
	field = le32_to_cpu(udev->bos->ext_cap->bmAttributes);  <<<<<<< here

	xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n",
			enable ? "enable" : "disable", port_num + 1);

	if (enable) {
		/* Host supports BESL timeout instead of HIRD */
		if (udev->usb2_hw_lpm_besl_capable) {
			/* if device doesn't have a preferred BESL value use a
			 * default one which works with mixed HIRD and BESL
			 * systems. See XHCI_DEFAULT_BESL definition in xhci.h
			 */
			if ((field & USB_BESL_SUPPORT) &&
			    (field & USB_BESL_BASELINE_VALID))
				hird = USB_GET_BESL_BASELINE(field);
			else
				hird = udev->l1_params.besl;

The failing case is when disabling LPM. So it is sufficient to avoid
access to udev->bos by moving the instruction into the "enable" clause.

Signed-off-by: Carsten Schmid 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

xhci: Don't let USB3 ports stuck in polling state prevent suspend

2019-08-13T11:38:52+00:00

commit d92f2c59cc2cbca6bfb2cc54882b58ba76b15fd4 upstream.

Commit 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.

Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.

Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).

Original patch was sent to stable, this one should go there as well

Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

usb: r8a66597: Fix a possible concurrency use-after-free bug in r8a66597_endpoint_disable()

2019-04-04T15:13:58+00:00

commit c85400f886e3d41e69966470879f635a2b50084c upstream.

The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may
be concurrently executed.
The two functions both access a possible shared variable "hep->hcpriv".

This shared variable is freed by r8a66597_endpoint_disable() via the
call path:
r8a66597_endpoint_disable
  kfree(hep->hcpriv) (line 1995 in Linux-4.19)

This variable is read by r8a66597_urb_enqueue() via the call path:
r8a66597_urb_enqueue
  spin_lock_irqsave(&r8a66597->lock)
  init_pipe_info
    enable_r8a66597_pipe
      pipe = hep->hcpriv (line 802 in Linux-4.19)

The read operation is protected by a spinlock, but the free operation
is not protected by this spinlock, thus a concurrency use-after-free bug
may occur.

To fix this bug, the spin-lock and spin-unlock function calls in
r8a66597_endpoint_disable() are moved to protect the free operation.

Signed-off-by: Jia-Ju Bai 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

xhci: Don't prevent USB2 bus suspend in state check intended for USB3 only

2019-02-11T17:54:26+00:00

commit 45f750c16cae3625014c14c77bd9005eda975d35 upstream.

The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.

Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well

Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

xhci: Prevent U1/U2 link pm states if exit latency is too long

2019-02-11T17:54:21+00:00

commit 0472bf06c6fd33c1a18aaead4c8f91e5a03d8d7b upstream.

Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.

This is according to xhci 1.1 specification section 4.23.5.2 extra note:

"Software shall ensure that a device is prevented from entering a U-state
 where its worst case exit latency approaches the ESIT."

Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.16: adjust context, indentation]
Signed-off-by: Ben Hutchings

xhci: workaround CSS timeout on AMD SNPS 3.0 xHC

2019-02-11T17:54:21+00:00

commit a7d57abcc8a5bdeb53bbf8e87558e8e0a2c2a29d upstream.

Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.

To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk

Signed-off-by: Shyam Sundar S K 
Signed-off-by: Sandeep Singh 
cc: Nehal Shah 
Tested-by: Kai-Heng Feng 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.16:
 - Use next available quirk bit
 - Fold in commit 2419f30a4a4f "USB: xhci: fix 'broken_suspend' placement ..."
 - Adjust context]
Signed-off-by: Ben Hutchings

USB: check usb_get_extra_descriptor for proper size

2019-02-11T17:54:20+00:00

commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream.

When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.

Reported-by: Hui Peng 
Reported-by: Mathias Payer 
Co-developed-by: Linus Torvalds 
Signed-off-by: Hui Peng 
Signed-off-by: Mathias Payer 
Signed-off-by: Linus Torvalds 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

usb: xhci: Prevent bus suspend if a port connect change or polling state is detected

2019-02-11T17:54:04+00:00

commit 2f31a67f01a8beb22cae754c53522cb61a005750 upstream.

USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.

USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.

If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.

The hub thread will notice the connect change and resume the bus,
moving the port back to U0

This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted

Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().

Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.16:
 - Keep  port_array[] to look up port I/O address
 - Adjust context]
Signed-off-by: Ben Hutchings

usb: xhci: fix timeout for transition from RExit to U0

2019-02-11T17:53:58+00:00

commit a5baeaeabcca3244782a9b6382ebab6f8a58f583 upstream.

This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.

Verified on Sunrise Point-LP and Cannon Lake.

Signed-off-by: Aaron Ma 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: xhci: fix uninitialized completion when USB3 port got wrong status

2019-02-11T17:53:58+00:00

commit 958c0bd86075d4ef1c936998deefe1947e539240 upstream.

Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.

Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.

Restrict the USB2 resume status check in USB2 roothub to fix hang issue.

Signed-off-by: Aaron Ma 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings