linux-stable.git/drivers/usb/host, branch v3.10.63

USB: xhci: don't start a halted endpoint before its new dequeue is set

2014-12-06T23:05:48+00:00

commit c3492dbfa1050debf23a5b5cd2bc7514c5b37896 upstream.

A halted endpoint ring must first be reset, then move the ring
dequeue pointer past the problematic TRB. If we start the ring too
early after reset, but before moving the dequeue pointer we
will end up executing the same problematic TRB again.

As we always issue a set transfer dequeue command after a reset
endpoint command we can skip starting endpoint rings at reset endpoint
command completion.

Without this fix we end up trying to handle the same faulty TD for
contol endpoints. causing timeout, and failing testusb ctrl_out write
tests.

Fixes: e9df17e (USB: xhci: Correct assumptions about number of rings per endpoint.)
Tested-by: Felipe Balbi 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb: host: xhci: fix compliance mode workaround

2014-10-05T21:54:13+00:00

commit 96908589a8b2584b1185f834d365f5cc360e8226 upstream.

Commit 71c731a (usb: host: xhci: Fix Compliance Mode
on SN65LVP3502CP Hardware) implemented a workaround
for a known issue with Texas Instruments' USB 3.0
redriver IC but it left a condition where any xHCI
host would be taken out of reset if port was placed
in compliance mode and there was no device connected
to the port.

That condition would trigger a fake connection to a
non-existent device so that usbcore would trigger a
warm reset of the port, thus taking the link out of
reset.

This has the side-effect of preventing any xHCI host
connected to a Linux machine from starting and running
the USB 3.0 Electrical Compliance Suite because the
port will mysteriously taken out of compliance mode
and, thus, xHCI won't step through the necessary
compliance patterns for link validation.

This patch fixes the issue by just adding a missing
check for XHCI_COMP_MODE_QUIRK inside
xhci_hub_report_usb3_link_state() when PORT_CAS isn't
set.

This patch should be backported to all kernels containing
commit 71c731a.

Fixes: 71c731a (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware)
Cc: Alexis R. Cortes 
Cc:  # v3.2+
Signed-off-by: Felipe Balbi 
Acked-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

USB: EHCI: unlink QHs even after the controller has stopped

2014-10-05T21:54:10+00:00

commit 7312b5ddd47fee2356baa78c5516ef8e04eed452 upstream.

Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH.  This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.

But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed.  Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.

Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.

Signed-off-by: Alan Stern 
Reported-by: Joe Lawrence 
Tested-by: Joe Lawrence 
Signed-off-by: Greg Kroah-Hartman

xhci: fix oops when xhci resumes from hibernate with hw lpm capable devices

2014-10-05T21:54:10+00:00

commit 96044694b8511bc2b04df0776b4ba295cfe005c0 upstream.

Resuming from hibernate (S4) will restart and re-initialize xHC.
The device contexts are freed and will be re-allocated later during device reset.

Usb core will disable link pm in device resume before device reset, which will
try to change the max exit latency, accessing the device contexts before they are re-allocated.

There is no need to zero (disable) the max exit latency when disabling hw lpm
for a freshly re-initialized xHC. So check that device context exists before
doing anything. The max exit latency will be set again after device reset when usb core
enables the link pm.

Reported-by: Imre Deak 
Tested-by: Imre Deak 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

xhci: Fix null pointer dereference if xhci initialization fails

2014-10-05T21:54:09+00:00

commit c207e7c50f31113c24a9f536fcab1e8a256985d7 upstream.

If xhci initialization fails before the roothub bandwidth
domains (xhci->rh_bw[i]) are allocated it will oops when
trying to access rh_bw members in xhci_mem_cleanup().

Reported-by: Manuel Reimer 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb: xhci: amd chipset also needs short TX quirk

2014-09-05T23:28:36+00:00

commit 2597fe99bb0259387111d0431691f5daac84f5a5 upstream.

AMD xHC also needs short tx quirk after tested on most of chipset
generations. That's because there is the same incorrect behavior like
Fresco Logic host. Please see below message with on USB webcam
attached on xHC host:

[  139.262944] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[  139.266934] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[  139.270913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[  139.274937] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[  139.278914] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[  139.282936] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[  139.286915] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[  139.290938] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[  139.294913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[  139.298917] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?

Reported-by: Arindam Nath 
Tested-by: Shriraj-Rai P 
Signed-off-by: Huang Rui 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

xhci: Treat not finding the event_seg on COMP_STOP the same as COMP_STOP_INVAL

2014-09-05T23:28:36+00:00

commit 9a54886342e227433aebc9d374f8ae268a836475 upstream.

When using a Renesas uPD720231 chipset usb-3 uas to sata bridge with a 120G
Crucial M500 ssd, model string: Crucial_ CT120M500SSD1, together with a
the integrated Intel xhci controller on a Haswell laptop:

00:14.0 USB controller [0c03]: Intel Corporation 8 Series USB xHCI HC [8086:9c31] (rev 04)

The following error gets logged to dmesg:

xhci error: Transfer event TRB DMA ptr not part of current TD

Treating COMP_STOP the same as COMP_STOP_INVAL when no event_seg gets found
fixes this.

Signed-off-by: Hans de Goede 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

USB: ehci-pci: USB host controller support for Intel Quark X1000

2014-09-05T23:28:34+00:00

commit 6e693739e9b603b3ca9ce0d4f4178f0633458465 upstream.

The EHCI packet buffer in/out threshold is programmable for Intel Quark X1000
USB host controller, and the default value is 0x20 dwords. The in/out threshold
can be programmed to 0x80 dwords (512 Bytes) to maximize the perfomrance,
but only when isochronous/interrupt transactions are not initiated by the USB
host controller. This patch is to reconfigure the packet buffer in/out
threshold as maximal as possible to maximize the performance, and 0x7F dwords
(508 Bytes) should be used because the USB host controller initiates
isochronous/interrupt transactions.

Signed-off-by: Bryan O'Donoghue 
Signed-off-by: Alvin (Weike) Chen 
Acked-by: Alan Stern 
Reviewed-by: Jingoo Han 
Signed-off-by: Greg Kroah-Hartman

USB: OHCI: don't lose track of EDs when a controller dies

2014-09-05T23:28:34+00:00

commit 977dcfdc60311e7aa571cabf6f39c36dde13339e upstream.

This patch fixes a bug in ohci-hcd.  When an URB is unlinked, the
corresponding Endpoint Descriptor is added to the ed_rm_list and taken
off the hardware schedule.  Once the ED is no longer visible to the
hardware, finish_unlinks() handles the URBs that were unlinked or have
completed.  If any URBs remain attached to the ED, the ED is added
back to the hardware schedule -- but only if the controller is
running.

This fails when a controller dies.  A non-empty ED does not get added
back to the hardware schedule and does not remain on the ed_rm_list;
ohci-hcd loses track of it.  The remaining URBs cannot be unlinked,
which causes the USB stack to hang.

The patch changes finish_unlinks() so that non-empty EDs remain on
the ed_rm_list if the controller isn't running.  This requires moving
some of the existing code around, to avoid modifying the ED's hardware
fields more than once.

Signed-off-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

xhci: Fix runtime suspended xhci from blocking system suspend.

2014-07-09T18:13:59+00:00

commit d6236f6d1d885aa19d1cd7317346fe795227a3cc upstream.

The system suspend flow as following:
1, Freeze all user processes and kenrel threads.

2, Try to suspend all devices.

2.1, If pci device is in RPM suspended state, then pci driver will try
to resume it to RPM active state in the prepare stage.

2.2, xhci_resume function calls usb_hcd_resume_root_hub to queue two
workqueue items to resume usb2&usb3 roothub devices.

2.3, Call suspend callbacks of devices.

2.3.1, All suspend callbacks of all hcd's children, including
roothub devices are called.

2.3.2, Finally, hcd_pci_suspend callback is called.

Due to workqueue threads were already frozen in step 1, the workqueue
items can't be scheduled, and the roothub devices can't be resumed in
this flow. The HCD_FLAG_WAKEUP_PENDING flag which is set in
usb_hcd_resume_root_hub won't be cleared. Finally,
hcd_pci_suspend will return -EBUSY, and system suspend fails.

The reason why this issue doesn't show up very often is due to that
choose_wakeup will be called in step 2.3.1. In step 2.3.1, if
udev->do_remote_wakeup is not equal to device_may_wakeup(&udev->dev), then
udev will resume to RPM active for changing the wakeup settings. This
has been a lucky hit which hides this issue.

For some special xHCI controllers which have no USB2 port, then roothub
will not match hub driver due to probe failed. Then its
do_remote_wakeup will be set to zero, and we won't be as lucky.

xhci driver doesn't need to resume roothub devices everytime like in
the above case. It's only needed when there are pending event TRBs.

This patch should be back-ported to kernels as old as 3.2, that
contains the commit f69e3120df82391a0ee8118e0a156239a06b2afb
"USB: XHCI: resume root hubs when the controller resumes"

Signed-off-by: Wang, Yu 
Acked-by: Alan Stern 
[use readl() instead of removed xhci_readl(), reword commit message -Mathias]
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman