linux-stable.git/drivers/usb/host, branch v3.0.63

USB: XHCI: fix memory leak of URB-private data

2013-02-11T16:16:49+00:00

commit 48c3375c5f69b1c2ef3d1051a0009cb9bce0ce24 upstream.

This patch (as1640) fixes a memory leak in xhci-hcd.  The urb_priv
data structure isn't always deallocated in the handle_tx_event()
routine for non-control transfers.  The patch adds a kfree() call so
that all paths end up freeing the memory properly.

This patch should be backported to kernels as old as 2.6.36, that
contain the commit 8e51adccd4c4b9ffcd509d7f2afce0a906139f75 "USB: xHCI:
Introduce urb_priv structure"

Signed-off-by: Alan Stern 
Signed-off-by: Sarah Sharp 
Reported-and-tested-by: Martin Mokrejs 
Signed-off-by: Greg Kroah-Hartman

xhci: Fix isoc TD encoding.

2013-02-11T16:16:49+00:00

commit 760973d2a74b93eb1697981f7448f0e62767cfc4 upstream.

An isochronous TD is comprised of one isochronous TRB chained to zero or
more normal TRBs.  Only the isoc TRB has the TBC and TLBPC fields.  The
normal TRBs must set those fields to zeroes.  The code was setting the
TBC and TLBPC fields for both isoc and normal TRBs.  Fix this.

This should be backported to stable kernels as old as 3.0, that contain
the commit b61d378f2da41c748aba6ca19d77e1e1c02bcea5 " xhci 1.0: Set
transfer burst last packet count field."

Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

USB: EHCI: fix bug in scheduling periodic split transfers

2013-02-11T16:16:48+00:00

commit 3e619d04159be54b3daa0b7036b0ce9e067f4b5d upstream.

This patch (as1654) fixes a very old bug in ehci-hcd, connected with
scheduling of periodic split transfers.  The calculations for
full/low-speed bus usage are all carried out after the correction for
bit-stuffing has been applied, but the values in the max_tt_usecs
array assume it hasn't been.  The array should allow for allocation of
up to 90% of the bus capacity, which is 900 us, not 780 us.

The symptom caused by this bug is that any isochronous transfer to a
full-speed device with a maxpacket size larger than about 980 bytes is
always rejected with a -ENOSPC error.

Signed-off-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: UHCI: fix IRQ race during initialization

2013-01-28T04:46:28+00:00

commit 0f815a0a700bc10547449bde6c106051a035a1b9 upstream.

This patch (as1644) fixes a race that occurs during startup in
uhci-hcd.  If the IRQ line is shared with other devices, it's possible
for the handler routine to be called before the data structures are
fully initialized.

The problem is fixed by adding a check to the IRQ handler routine.  If
the initialization hasn't finished yet, the routine will return
immediately.

Signed-off-by: Alan Stern 
Reported-by: Don Zickus 
Tested-by: "Huang, Adrian (ISS Linux TW)" 
Signed-off-by: Greg Kroah-Hartman

xhci: fix null-pointer dereference when destroying half-built segment rings

2013-01-21T19:44:59+00:00

commit 68e5254adb88bede68285f11fb442a4d34fb550c upstream.

xhci_alloc_segments_for_ring() builds a list of xhci_segments and links
the tail to head at the end (forming a ring). When it bails out for OOM
reasons half-way through, it tries to destroy its half-built list with
xhci_free_segments_for_ring(), even though it is not a ring yet. This
causes a null-pointer dereference upon hitting the last element.

Furthermore, one of its callers (xhci_ring_alloc()) mistakenly believes
the output parameters to be valid upon this kind of OOM failure, and
calls xhci_ring_free() on them. Since the (incomplete) list/ring should
already be destroyed in that case, this would lead to a use after free.

This patch fixes those issues by having xhci_alloc_segments_for_ring()
destroy its half-built, non-circular list manually and destroying the
invalid struct xhci_ring in xhci_ring_alloc() with a plain kfree().

This patch should be backported to kernels as old as 2.6.31, that
contains the commit 0ebbab37422315a5d0cb29792271085bafdf38c0 "USB: xhci:
Ring allocation and initialization."

A separate patch will need to be developed for kernels older than 3.4,
since the ring allocation code was refactored in that kernel.

Signed-off-by: Julius Werner 
Signed-off-by: Sarah Sharp 
Signed-off-by: Julius Werner 
Signed-off-by: Sarah Sharp 
[bwh: Backported to 3.2:
 - Adjust context
 - Since segment allocation is done directly in xhci_ring_alloc(), walk
   the list starting from ring->first_seg when freeing]
Signed-off-by: Ben Hutchings 
Signed-off-by: CAI Qian 
Signed-off-by: Greg Kroah-Hartman

xhci: Handle HS bulk/ctrl endpoints that don't NAK.

2013-01-17T16:44:12+00:00

commit 55c1945edaac94c5338a3647bc2e85ff75d9cf36 upstream.

A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK.  If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).

The xHCI code to compute the NAK interval does not handle the special
case of zero properly.  The current code unconditionally subtracts one
from bInterval and uses it as an exponent.  This causes a very large
bInterval to be used, and warning messages like these will be printed:

usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes

This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.

This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math in
xhci_get_endpoint_interval()".

Reported-by: Vincent Pelletier 
Suggested-by: Alan Stern 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

xhci: Add Lynx Point LP to list of Intel switchable hosts

2013-01-11T17:03:41+00:00

commit bb1e5dd7113d2fd178d3af9aca8f480ae0468edf upstream.

Like Lynx Point, Lynx Point LP is also switchable.  See
1c12443ab8eba71a658fae4572147e56d1f84f66 for more details.

This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."

Signed-off-by: Russell Webb 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

xhci: Extend Fresco Logic MSI quirk.

2012-12-17T18:49:05+00:00

commit bba18e33f25072ebf70fd8f7f0cdbf8cdb59a746 upstream.

Ali reports that plugging a device into the Fresco Logic xHCI host with
PCI device ID 1400 produces an IRQ error:

 do_IRQ: 3.176 No irq handler for vector (irq -1)

Other early Fresco Logic host revisions don't support MSI, even though
their PCI config space claims they do.  Extend the quirk to disabling
MSI to this chipset revision.  Also enable the short transfer quirk,
since it's likely this revision also has that quirk, and it should be
harmless to enable.

04:00.0 0c03: 1b73:1400 (rev 01) (prog-if 30 [XHCI])
        Subsystem: 1d5c:1000
        Physical Slot: 3
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 
Reported-by: A Sh 
Tested-by: A Sh 
Signed-off-by: Greg Kroah-Hartman

USB: OHCI: workaround for hardware bug: retired TDs not added to the Done Queue

2012-12-17T18:49:04+00:00

commit 50ce5c0683aa83eb161624ea89daa5a9eee0c2ce upstream.

This patch (as1636) is a partial workaround for a hardware bug
affecting OHCI controllers by NVIDIA at least, maybe others too.  When
the controller retires a Transfer Descriptor, it is supposed to add
the TD onto the Done Queue.  But sometimes this doesn't happen, with
the result that ohci-hcd never realizes the corresponding transfer has
finished.  Symptoms can vary; a typical result is that USB audio stops
working after a while.

The patch works around the problem by recognizing that TDs are always
processed in order.  Therefore, if a later TD is found on the Done
Queue than all the earlier TDs for the same endpoint must be finished
as well.

Unfortunately this won't solve the problem in cases where the missing
TD is the last one in the endpoint's queue.  A complete fix would
require a signficant amount of change to the driver.

Signed-off-by: Alan Stern 
Tested-by: Oliver Neukum 
Signed-off-by: Greg Kroah-Hartman

xhci: Fix potential NULL ptr deref in command cancellation.

2012-10-31T16:51:36+00:00

commit 43a09f7fb01fa1e091416a2aa49b6c666458c1ee upstream.

The command cancellation code doesn't check whether find_trb_seg()
couldn't find the segment that contains the TRB to be canceled.  This
could cause a NULL pointer deference later in the function when next_trb
is called.  It's unlikely to happen unless something is wrong with the
command ring pointers, so add some debugging in case it happens.

This patch should be backported to stable kernels as old as 3.0, that
contain the commit b63f4053cc8aa22a98e3f9a97845afe6c15d0a0d "xHCI:
handle command after aborting the command ring".

Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman