linux-stable.git/drivers/usb/host, branch v3.0.45 Linux kernel stable tree Increase XHCI suspend timeout to 16ms 2012-10-07T15:27:26+00:00 Michael Spang spang@chromium.org 2012-09-14T17:05:49+00:00 a4e92d29a86daf9609c875eccb1357657f2ac93f commit a6e097dfdfd189b6929af6efa1d289af61858386 upstream. The Intel XHCI specification says that after clearing the run/stop bit the controller may take up to 16ms to halt. We've seen a device take 14ms, which with the current timeout of 10ms causes the kernel to abort the suspend. Increasing the timeout to the recommended value fixes the problem. This patch should be backported to kernels as old as 2.6.37, that contain the commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI: PCI power management implementation". Signed-off-by: Michael Spang <spang@chromium.org> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a6e097dfdfd189b6929af6efa1d289af61858386 upstream.

The Intel XHCI specification says that after clearing the run/stop bit
the controller may take up to 16ms to halt. We've seen a device take
14ms, which with the current timeout of 10ms causes the kernel to
abort the suspend. Increasing the timeout to the recommended value
fixes the problem.

This patch should be backported to kernels as old as 2.6.37, that
contain the commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI:
PCI power management implementation".

Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Intel Panther Point BEI quirk. 2012-10-07T15:27:25+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-09-19T23:27:26+00:00 9c1ce83c1250a3ad4c2d131d59295561b09efe83 commit 80fab3b244a22e0ca539d2439bdda50e81e5666f upstream. When a device with an isochronous endpoint is behind a hub plugged into the Intel Panther Point xHCI host controller, and the driver submits multiple frames per URB, the xHCI driver will set the Block Event Interrupt (BEI) flag on all but the last TD for the URB. This causes the host controller to place an event on the event ring, but not send an interrupt. When the last TD for the URB completes, BEI is cleared, and we get an interrupt for the whole URB. However, under a Panther Point xHCI host controller, if the parent hub is unplugged when one or more events from transfers with BEI set are on the event ring, a port status change event is placed on the event ring, but no interrupt is generated. This means URBs stop completing, and the USB device disconnect is not noticed. Something like a USB headset will cause mplayer to hang when the device is disconnected. If another transfer is sent (such as running `sudo lsusb -v`), the next transfer event seems to "unstick" the event ring, the xHCI driver gets an interrupt, and the disconnect is reported to the USB core. The fix is not to use the BEI flag under the Panther Point xHCI host. This will impact power consumption and system responsiveness, because the xHCI driver will receive an interrupt for every frame in all isochronous URBs instead of once per URB. Intel chipset developers confirm that this bug will be hit if the BEI flag is used on any endpoint, not just ones that are behind a hub. This patch should be backported to kernels as old as 3.0, that contain the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 80fab3b244a22e0ca539d2439bdda50e81e5666f upstream.

When a device with an isochronous endpoint is behind a hub plugged into
the Intel Panther Point xHCI host controller, and the driver submits
multiple frames per URB, the xHCI driver will set the Block Event
Interrupt (BEI) flag on all but the last TD for the URB.  This causes
the host controller to place an event on the event ring, but not send an
interrupt.  When the last TD for the URB completes, BEI is cleared, and
we get an interrupt for the whole URB.

However, under a Panther Point xHCI host controller, if the parent hub
is unplugged when one or more events from transfers with BEI set are on
the event ring, a port status change event is placed on the event ring,
but no interrupt is generated.  This means URBs stop completing, and the
USB device disconnect is not noticed.  Something like a USB headset will
cause mplayer to hang when the device is disconnected.

If another transfer is sent (such as running `sudo lsusb -v`), the next
transfer event seems to "unstick" the event ring, the xHCI driver gets
an interrupt, and the disconnect is reported to the USB core.

The fix is not to use the BEI flag under the Panther Point xHCI host.
This will impact power consumption and system responsiveness, because
the xHCI driver will receive an interrupt for every frame in all
isochronous URBs instead of once per URB.

Intel chipset developers confirm that this bug will be hit if the BEI
flag is used on any endpoint, not just ones that are behind a hub.

This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Fix bug after deq ptr set to link TRB. 2012-10-02T16:47:39+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-07-26T19:03:59+00:00 e3439be1c0b9df0ca9b760ff4861be5d6145da26 commit 50d0206fcaea3e736f912fd5b00ec6233fb4ce44 upstream. This patch fixes a particularly nasty bug that was revealed by the ring expansion patches. The bug has been present since the very beginning of the xHCI driver history, and could have caused general protection faults from bad memory accesses. The first thing to note is that a Set TR Dequeue Pointer command can move the dequeue pointer to a link TRB, if the canceled or stalled transfer TD ended just before a link TRB. The function to increment the dequeue pointer, inc_deq, was written before cancellation and stall support was added. It assumed that the dequeue pointer could never point to a link TRB. It would unconditionally increment the dequeue pointer at the start of the function, check if the pointer was now on a link TRB, and move it to the top of the next segment if so. This means that if a Set TR Dequeue Point command moved the dequeue pointer to a link TRB, a subsequent call to inc_deq() would move the pointer off the segment and into la-la-land. It would then read from that memory to determine if it was a link TRB. Other functions would often call inc_deq() until the dequeue pointer matched some other pointer, which means this function would quite happily read all of system memory before wrapping around to the right pointer value. Often, there would be another endpoint segment from a different ring allocated from the same DMA pool, which would be contiguous to the segment inc_deq just stepped off of. inc_deq would eventually find the link TRB in that segment, and blindly move the dequeue pointer back to the top of the correct ring segment. The only reason the original code worked at all is because there was only one ring segment. With the ring expansion patches, the dequeue pointer would eventually wrap into place, but the dequeue segment would be out-of-sync. On the second TD after the dequeue pointer was moved to a link TRB, trb_in_td() would fail (because the dequeue pointer and dequeue segment were out-of-sync), and this message would appear: ERROR Transfer event TRB DMA ptr not part of current TD This fixes bugzilla entry 4333 (option-based modem unhappy on USB 3.0 port: "Transfer event TRB DMA ptr not part of current TD", "rejecting I/O to offline device"), https://bugzilla.kernel.org/show_bug.cgi?id=43333 and possibly other general protection fault bugs as well. This patch should be backported to kernels as old as 2.6.31. A separate patch will be created for kernels older than 3.4, since inc_deq was modified in 3.4 and this patch will not apply. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: James Ettle <theholyettlz@googlemail.com> Tested-by: Matthew Hall <mhall@mhcomputing.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 50d0206fcaea3e736f912fd5b00ec6233fb4ce44 upstream.

This patch fixes a particularly nasty bug that was revealed by the ring
expansion patches.  The bug has been present since the very beginning of
the xHCI driver history, and could have caused general protection faults
from bad memory accesses.

The first thing to note is that a Set TR Dequeue Pointer command can
move the dequeue pointer to a link TRB, if the canceled or stalled
transfer TD ended just before a link TRB.  The function to increment the
dequeue pointer, inc_deq, was written before cancellation and stall
support was added.  It assumed that the dequeue pointer could never
point to a link TRB.  It would unconditionally increment the dequeue
pointer at the start of the function, check if the pointer was now on a
link TRB, and move it to the top of the next segment if so.

This means that if a Set TR Dequeue Point command moved the dequeue
pointer to a link TRB, a subsequent call to inc_deq() would move the
pointer off the segment and into la-la-land.  It would then read from
that memory to determine if it was a link TRB.  Other functions would
often call inc_deq() until the dequeue pointer matched some other
pointer, which means this function would quite happily read all of
system memory before wrapping around to the right pointer value.

Often, there would be another endpoint segment from a different ring
allocated from the same DMA pool, which would be contiguous to the
segment inc_deq just stepped off of.  inc_deq would eventually find the
link TRB in that segment, and blindly move the dequeue pointer back to
the top of the correct ring segment.

The only reason the original code worked at all is because there was
only one ring segment.  With the ring expansion patches, the dequeue
pointer would eventually wrap into place, but the dequeue segment would
be out-of-sync.  On the second TD after the dequeue pointer was moved to
a link TRB, trb_in_td() would fail (because the dequeue pointer and
dequeue segment were out-of-sync), and this message would appear:

ERROR Transfer event TRB DMA ptr not part of current TD

This fixes bugzilla entry 4333 (option-based modem unhappy on USB 3.0
port: "Transfer event TRB DMA ptr not part of current TD", "rejecting
I/O to offline device"),

	https://bugzilla.kernel.org/show_bug.cgi?id=43333

and possibly other general protection fault bugs as well.

This patch should be backported to kernels as old as 2.6.31.  A separate
patch will be created for kernels older than 3.4, since inc_deq was
modified in 3.4 and this patch will not apply.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: James Ettle <theholyettlz@googlemail.com>
Tested-by: Matthew Hall <mhall@mhcomputing.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: host: xhci: fix compilation error for non-PCI based stacks 2012-10-02T16:47:39+00:00 Moiz Sonasath m-sonasath@ti.com 2012-09-05T05:34:26+00:00 d8ec66c5a565c5ca47d2740226f3e2035c1883bf commit 296365781903226a3fb8758901eaeec09d2798e4 upstream. For non PCI-based stacks, this function call usb_disable_xhci_ports(to_pci_dev(hcd->self.controller)); made from xhci_shutdown is not applicable. Ideally, we wouldn't have any PCI-specific code on a generic driver such as the xHCI stack, but it looks like we should just stub usb_disable_xhci_ports() out for non-PCI devices. [ balbi@ti.com: slight improvement to commit log ] This patch should be backported to kernels as old as 3.0, since the commit it fixes (e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch PPT ports to EHCI on shutdown.") was marked for stable. Signed-off-by: Moiz Sonasath<m-sonasath@ti.com> Signed-off-by: Ruchika Kharwar <ruchika@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 296365781903226a3fb8758901eaeec09d2798e4 upstream.

For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.

Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.

[ balbi@ti.com: slight improvement to commit log ]

This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.

Signed-off-by: Moiz Sonasath<m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Recognize USB 3.0 devices as superspeed at powerup 2012-10-02T16:47:39+00:00 Manoj Iyer manoj.iyer@canonical.com 2012-08-22T16:53:18+00:00 b1e81baa2d46338345c6f16c0e873ef3e7d73188 commit 29d214576f936db627ff62afb9ef438eea18bcd2 upstream. On Intel Panther Point chipset USB 3.0 devices show up as high-speed devices on powerup, but after an s3 cycle they are correctly recognized as SuperSpeed. At powerup switch the port to xHCI so that USB 3.0 devices are correctly recognized. BugLink: http://bugs.launchpad.net/bugs/1000424 This patch should be backported to kernels as old as 3.0, that contain commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 29d214576f936db627ff62afb9ef438eea18bcd2 upstream.

On Intel Panther Point chipset USB 3.0 devices show up as
high-speed devices on powerup, but after an s3 cycle they are
correctly recognized as SuperSpeed. At powerup switch the port
to xHCI so that USB 3.0 devices are correctly recognized.

BugLink: http://bugs.launchpad.net/bugs/1000424

This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."

Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Make handover code more robust 2012-10-02T16:47:39+00:00 Matthew Garrett mjg@redhat.com 2012-08-14T20:44:49+00:00 f78e6ad433084ec0b7bc40ff9910f458609ee9cb commit e955a1cd086de4d165ae0f4c7be7289d84b63bdc upstream. My test platform (Intel DX79SI) boots reliably under BIOS, but frequently crashes when booting via UEFI. I finally tracked this down to the xhci handoff code. It seems that reads from the device occasionally just return 0xff, resulting in xhci_find_next_cap_offset generating a value that's larger than the resource region. We then oops when attempting to read the value. Sanity checking that value lets us avoid the crash. I've no idea what's causing the underlying problem, and xhci still doesn't actually *work* even with this, but the machine at least boots which will probably make further debugging easier. This should be backported to kernels as old as 2.6.31, that contain the commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci: BIOS handoff and HW initialization." Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit e955a1cd086de4d165ae0f4c7be7289d84b63bdc upstream.

My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.

I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.

This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci: BIOS handoff
and HW initialization."

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Fix a logical vs bitwise AND bug 2012-10-02T16:47:39+00:00 Dan Carpenter dan.carpenter@oracle.com 2012-08-13T16:57:03+00:00 c0a168c0f20189efc03264785edd55baf00d5acc commit 052c7f9ffb0e95843e75448d02664459253f9ff8 upstream. The intent was to test whether the flag was set. This patch should be backported to stable kernels as old as 3.0, since it fixes a bug in commit e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch PPT ports to EHCI on shutdown.", which was marked for stable. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 052c7f9ffb0e95843e75448d02664459253f9ff8 upstream.

The intent was to test whether the flag was set.

This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f474f0db3a4d940cae1423783edd966027 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel xhci: Only switch the switchable ports 2012-10-02T16:47:39+00:00 Keng-Yu Lin kengyu@canonical.com 2012-08-09T17:39:23+00:00 4a4c06b80e8b0de688d0e71b7206aabeb2f8ea7f commit a96874a2a92feaef607ddd3137277a788cb927a6 upstream. With a previous patch to enable the EHCI/XHCI port switching, it switches all the available ports. The assumption is not correct because the BIOS may expect some ports not switchable by the OS. There are two more registers that contains the information of the switchable and non-switchable ports. This patch adds the checking code for the two register so that only the switchable ports are altered. This patch should be backported to kernels as old as 3.0, that contain commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by: Keng-Yu Lin <kengyu@canonical.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a96874a2a92feaef607ddd3137277a788cb927a6 upstream.

With a previous patch to enable the EHCI/XHCI port switching, it switches
all the available ports.

The assumption is not correct because the BIOS may expect some ports
not switchable by the OS.

There are two more registers that contains the information of the switchable
and non-switchable ports.

This patch adds the checking code for the two register so that only the
switchable ports are altered.

This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."

Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EHCI: Update qTD next pointer in QH overlay region during unlink 2012-10-02T16:47:38+00:00 Pavankumar Kondeti pkondeti@codeaurora.org 2012-09-07T05:53:28+00:00 ebf16a5b74e2f91cbfce4179064c35529ba9afad commit 3d037774b42ed677f699b1dce7d548d55f4e4c2b upstream. There is a possibility of QH overlay region having reference to a stale qTD pointer during unlink. Consider an endpoint having two pending qTD before unlink process begins. The endpoint's QH queue looks like this. qTD1 --> qTD2 --> Dummy To unlink qTD2, QH is removed from asynchronous list and Asynchronous Advance Doorbell is programmed. The qTD1's next qTD pointer is set to qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell interrupt. If QH's current qTD pointer points to qTD1, transfer overlay region still have reference to qTD2. But qtD2 is just unlinked and freed. This may cause EHCI system error. Fix this by updating qTD next pointer in QH overlay region with the qTD next pointer of the current qTD. Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 3d037774b42ed677f699b1dce7d548d55f4e4c2b upstream.

There is a possibility of QH overlay region having reference to a stale
qTD pointer during unlink.

Consider an endpoint having two pending qTD before unlink process begins.
The endpoint's QH queue looks like this.

qTD1 --> qTD2 --> Dummy

To unlink qTD2, QH is removed from asynchronous list and Asynchronous
Advance Doorbell is programmed.  The qTD1's next qTD pointer is set to
qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell
interrupt.  If QH's current qTD pointer points to qTD1, transfer overlay
region still have reference to qTD2. But qtD2 is just unlinked and freed.
This may cause EHCI system error.  Fix this by updating qTD next pointer
in QH overlay region with the qTD next pointer of the current qTD.

Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Switch PPT ports to EHCI on shutdown. 2012-08-26T22:12:12+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-07-23T15:59:30+00:00 0135372d5c4305a59aee0091847da7ce0cf08ffe commit e95829f474f0db3a4d940cae1423783edd966027 upstream. The Intel desktop boards DH77EB and DH77DF have a hardware issue that can be worked around by BIOS. If the USB ports are switched to xHCI on shutdown, the xHCI host will send a spurious interrupt, which will wake the system. Some BIOS will work around this, but not all. The bug can be avoided if the USB ports are switched back to EHCI on shutdown. The Intel Windows driver switches the ports back to EHCI, so change the Linux xHCI driver to do the same. Unfortunately, we can't tell the two effected boards apart from other working motherboards, because the vendors will change the DMI strings for the DH77EB and DH77DF boards to their own custom names. One example is Compulab's mini-desktop, the Intense-PC. Instead, key off the Panther Point xHCI host PCI vendor and device ID, and switch the ports over for all PPT xHCI hosts. The only impact this will have on non-effected boards is to add a couple hundred milliseconds delay on boot when the BIOS has to switch the ports over from EHCI to xHCI. This patch should be backported to kernels as old as 3.0, that contain the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Denis Turischev <denis@compulab.co.il> Tested-by: Denis Turischev <denis@compulab.co.il> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit e95829f474f0db3a4d940cae1423783edd966027 upstream.

The Intel desktop boards DH77EB and DH77DF have a hardware issue that
can be worked around by BIOS.  If the USB ports are switched to xHCI on
shutdown, the xHCI host will send a spurious interrupt, which will wake
the system.  Some BIOS will work around this, but not all.

The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.  The Intel Windows driver switches the ports back to EHCI, so
change the Linux xHCI driver to do the same.

Unfortunately, we can't tell the two effected boards apart from other
working motherboards, because the vendors will change the DMI strings
for the DH77EB and DH77DF boards to their own custom names.  One example
is Compulab's mini-desktop, the Intense-PC.  Instead, key off the
Panther Point xHCI host PCI vendor and device ID, and switch the ports
over for all PPT xHCI hosts.

The only impact this will have on non-effected boards is to add a couple
hundred milliseconds delay on boot when the BIOS has to switch the ports
over from EHCI to xHCI.

This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Denis Turischev <denis@compulab.co.il>
Tested-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>