linux-stable.git/drivers/usb/host, branch v3.0.41 Linux kernel stable tree xhci: Avoid dead ports when CONFIG_USB_XHCI_HCD=n 2012-07-16T15:47:50+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-06-22T16:51:03+00:00 671e3aaf0ce971311ab8405bf2acc295ce999529 Commit 51c9e6c7732b67769c0a514d31f505e49fa82dd4 upstream, but modified to get this to apply on 3.0. If the user chooses to say "no" to CONFIG_USB_XHCI_HCD on a system with an Intel Panther Point chipset, the PCI quirks code or the EHCI driver will switch the ports over to the xHCI host, but the xHCI driver will never load. The ports will be powered off and seem "dead" to the user. Fix this by only switching the ports over if CONFIG_USB_XHCI_HCD is either compiled in, or compiled as a module. This patch should be backported to the 3.0 stable kernel, since it contains the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Eric Anholt <eric.anholt@intel.com> Reported-by: David Bein <d.bein@f5.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Commit 51c9e6c7732b67769c0a514d31f505e49fa82dd4 upstream, but modified
to get this to apply on 3.0.

If the user chooses to say "no" to CONFIG_USB_XHCI_HCD on a system
with an Intel Panther Point chipset, the PCI quirks code or the EHCI
driver will switch the ports over to the xHCI host, but the xHCI driver
will never load.  The ports will be powered off and seem "dead" to the
user.

Fix this by only switching the ports over if CONFIG_USB_XHCI_HCD is
either compiled in, or compiled as a module.

This patch should be backported to the 3.0 stable kernel, since it
contains the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel
xhci: Support EHCI/xHCI port switching."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Eric Anholt <eric.anholt@intel.com>
Reported-by: David Bein <d.bein@f5.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: add NO_D3_DURING_SLEEP flag and revert 151b61284776be2 2012-06-22T18:34:15+00:00 Alan Stern stern@rowland.harvard.edu 2012-06-13T15:20:19+00:00 2c1a56c8c620ff93050ee4ef545cc585d2f93034 commit c2fb8a3fa25513de8fedb38509b1f15a5bbee47b upstream. This patch (as1558) fixes a problem affecting several ASUS computers: The machine crashes or corrupts memory when going into suspend if the ehci-hcd driver is bound to any controllers. Users have been forced to unbind or unload ehci-hcd before putting their systems to sleep. After extensive testing, it was determined that the machines don't like going into suspend when any EHCI controllers are in the PCI D3 power state. Presumably this is a firmware bug, but there's nothing we can do about it except to avoid putting the controllers in D3 during system sleep. The patch adds a new flag to indicate whether the problem is present, and avoids changing the controller's power state if the flag is set. Runtime suspend is unaffected; this matters only for system suspend. However as a side effect, the controller will not respond to remote wakeup requests while the system is asleep. Hence USB wakeup is not functional -- but of course, this is already true in the current state of affairs. A similar patch has already been applied as commit 151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during suspend on ASUS computers). The patch supersedes that one and reverts it. There are two differences: The old patch added the flag at the USB level; this patch adds it at the PCI level. The old patch applied to all chipsets with the same vendor, subsystem vendor, and product IDs; this patch makes an exception for a known-good system (based on DMI information). Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Dâniel Fraga <fragabr@gmail.com> Tested-by: Andrey Rahmatullin <wrar@wrar.name> Tested-by: Steven Rostedt <rostedt@goodmis.org> Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c2fb8a3fa25513de8fedb38509b1f15a5bbee47b upstream.

This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

A similar patch has already been applied as commit
151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during
suspend on ASUS computers).  The patch supersedes that one and reverts
it.  There are two differences:

	The old patch added the flag at the USB level; this patch
	adds it at the PCI level.

	The old patch applied to all chipsets with the same vendor,
	subsystem vendor, and product IDs; this patch makes an
	exception for a known-good system (based on DMI information).

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI: Increase the timeout for controller save/restore state operation 2012-06-22T18:34:14+00:00 Andiry Xu andiry.xu@gmail.com 2012-06-13T02:51:57+00:00 482a7756a282b7873dcba9441504a32354317d49 commit 622eb783fe6ff4c1baa47db16c3a5db97f9e6e50 upstream. When system software decides to power down the xHC with the intent of resuming operation at a later time, it will ask xHC to save the internal state and restore it when resume to correctly recover from a power event. Two bits are used to enable this operation: Save State and Restore State. xHCI spec 4.23.2 says software should "Set the Controller Save/Restore State flag in the USBCMD register and wait for the Save/Restore State Status flag in the USBSTS register to transition to '0'". However, it does not define how long software should wait for the SSS/RSS bit to transition to 0. Currently the timeout is set to 1ms. There is bug report (https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1002697) indicates that the timeout is too short for ASMedia ASM1042 host controller to save/restore the state successfully. Increase the timeout to 10ms helps to resolve the issue. This patch should be backported to stable kernels as old as 2.6.37, that contain the commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI: PCI power management implementation" Signed-off-by: Andiry Xu <andiry.xu@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Ming Lei <ming.lei@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 622eb783fe6ff4c1baa47db16c3a5db97f9e6e50 upstream.

When system software decides to power down the xHC with the intent of
resuming operation at a later time, it will ask xHC to save the internal
state and restore it when resume to correctly recover from a power event.
Two bits are used to enable this operation: Save State and Restore State.

xHCI spec 4.23.2 says software should "Set the Controller Save/Restore
State flag in the USBCMD register and wait for the Save/Restore State
Status flag in the USBSTS register to transition to '0'". However, it does
not define how long software should wait for the SSS/RSS bit to transition
to 0.

Currently the timeout is set to 1ms. There is bug report
(https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1002697)
indicates that the timeout is too short for ASMedia ASM1042 host controller
to save/restore the state successfully. Increase the timeout to 10ms helps to
resolve the issue.

This patch should be backported to stable kernels as old as 2.6.37, that
contain the commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI:
PCI power management implementation"

Signed-off-by: Andiry Xu <andiry.xu@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Add new short TX quirk for Fresco Logic host. 2012-06-01T07:12:59+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-05-08T16:22:49+00:00 d818cf47642e6379d61d9304fed3ca7c9d6786a8 commit 1530bbc6272d9da1e39ef8e06190d42c13a02733 upstream. Sergio reported that when he recorded audio from a USB headset mic plugged into the USB 3.0 port on his ASUS N53SV-DH72, the audio sounded "robotic". When plugged into the USB 2.0 port under EHCI on the same laptop, the audio sounded fine. The device is: Bus 002 Device 004: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset The problem was tracked down to the Fresco Logic xHCI host controller not correctly reporting short transfers on isochronous IN endpoints. The driver would submit a 96 byte transfer, the device would only send 88 or 90 bytes, and the xHCI host would report the transfer had a "successful" completion code, with an untransferred buffer length of 8 or 6 bytes. The successful completion code and non-zero untransferred length is a contradiction. The xHCI host is supposed to only mark a transfer as successful if all the bytes are transferred. Otherwise, the transfer should be marked with a short packet completion code. Without the EHCI bus trace, we wouldn't know whether the xHCI driver should trust the completion code or the untransferred length. With it, we know to trust the untransferred length. Add a new xHCI quirk for the Fresco Logic host controller. If a transfer is reported as successful, but the untransferred length is non-zero, print a warning. For the Fresco Logic host, change the completion code to COMP_SHORT_TX and process the transfer like a short transfer. This should be backported to stable kernels that contain the commit f5182b4155b9d686c5540a6822486400e34ddd98 "xhci: Disable MSI for some Fresco Logic hosts." That commit was marked for stable kernels as old as 2.6.36. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Sergio Correia <lists@uece.net> Tested-by: Sergio Correia <lists@uece.net> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 1530bbc6272d9da1e39ef8e06190d42c13a02733 upstream.

Sergio reported that when he recorded audio from a USB headset mic
plugged into the USB 3.0 port on his ASUS N53SV-DH72, the audio sounded
"robotic".  When plugged into the USB 2.0 port under EHCI on the same
laptop, the audio sounded fine.  The device is:

Bus 002 Device 004: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset

The problem was tracked down to the Fresco Logic xHCI host controller
not correctly reporting short transfers on isochronous IN endpoints.
The driver would submit a 96 byte transfer, the device would only send
88 or 90 bytes, and the xHCI host would report the transfer had a
"successful" completion code, with an untransferred buffer length of 8
or 6 bytes.

The successful completion code and non-zero untransferred length is a
contradiction.  The xHCI host is supposed to only mark a transfer as
successful if all the bytes are transferred.  Otherwise, the transfer
should be marked with a short packet completion code.  Without the EHCI
bus trace, we wouldn't know whether the xHCI driver should trust the
completion code or the untransferred length.  With it, we know to trust
the untransferred length.

Add a new xHCI quirk for the Fresco Logic host controller.  If a
transfer is reported as successful, but the untransferred length is
non-zero, print a warning.  For the Fresco Logic host, change the
completion code to COMP_SHORT_TX and process the transfer like a short
transfer.

This should be backported to stable kernels that contain the commit
f5182b4155b9d686c5540a6822486400e34ddd98 "xhci: Disable MSI for some
Fresco Logic hosts."  That commit was marked for stable kernels as old
as 2.6.36.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Sergio Correia <lists@uece.net>
Tested-by: Sergio Correia <lists@uece.net>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Reset reserved command ring TRBs on cleanup. 2012-06-01T07:12:58+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-05-08T14:09:26+00:00 c97ecdcfde93b2b05a0e5f3b5eaaf38e750337ae commit 33b2831ac870d50cc8e01c317b07fb1e69c13fe1 upstream. When the xHCI driver needs to clean up memory (perhaps due to a failed register restore on resume from S3 or resume from S4), it needs to reset the number of reserved TRBs on the command ring to zero. Otherwise, several resume cycles (about 30) with a UAS device attached will continually increment the number of reserved TRBs, until all command submissions fail because there isn't enough room on the command ring. This patch should be backported to kernels as old as 2.6.32, that contain the commit 913a8a344ffcaf0b4a586d6662a2c66a7106557d "USB: xhci: Change how xHCI commands are handled." Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 33b2831ac870d50cc8e01c317b07fb1e69c13fe1 upstream.

When the xHCI driver needs to clean up memory (perhaps due to a failed
register restore on resume from S3 or resume from S4), it needs to reset
the number of reserved TRBs on the command ring to zero.  Otherwise,
several resume cycles (about 30) with a UAS device attached will
continually increment the number of reserved TRBs, until all command
submissions fail because there isn't enough room on the command ring.

This patch should be backported to kernels as old as 2.6.32,
that contain the commit 913a8a344ffcaf0b4a586d6662a2c66a7106557d
"USB: xhci: Change how xHCI commands are handled."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb-xhci: Handle COMP_TX_ERR for isoc tds 2012-06-01T07:12:58+00:00 Hans de Goede hdegoede@redhat.com 2012-04-23T13:06:09+00:00 1a4573e4e0bb86436881b7120a80cfb63d647a0f commit 9c745995ae5c4ff787f34a359de908facc11ee00 upstream. While testing unplugging an UVC HD webcam with usb-redirection (so through usbdevfs), my userspace usb-redir code was getting a value of -1 in iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt is not a valid value. The source of this -1 is the default case in xhci-ring.c:process_isoc_td() adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR in this case, so this patch adds handling for that completion code to process_isoc_td(). This was observed and tested with the following xhci controller: 1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can do, but since I cannot come up with anything better I've left that as is. This patch should be backported to kernels as old as 2.6.36, which contain the commit 04e51901dd44f40a5a385ced897f6bca87d5f40a "USB: xHCI: Isochronous transfer implementation". Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 9c745995ae5c4ff787f34a359de908facc11ee00 upstream.

While testing unplugging an UVC HD webcam with usb-redirection (so through
usbdevfs), my userspace usb-redir code was getting a value of -1 in
iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt
is not a valid value.

The source of this -1 is the default case in xhci-ring.c:process_isoc_td()
adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR
in this case, so this patch adds handling for that completion code to
process_isoc_td().

This was observed and tested with the following xhci controller:
1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)

Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can
do, but since I cannot come up with anything better I've left that as is.

This patch should be backported to kernels as old as 2.6.36, which contain the
commit 04e51901dd44f40a5a385ced897f6bca87d5f40a "USB: xHCI: Isochronous
transfer implementation".

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci: Add Lynx Point to list of Intel switchable hosts. 2012-06-01T07:12:58+00:00 Sarah Sharp sarah.a.sharp@linux.intel.com 2012-02-09T23:55:13+00:00 36a51c272d5b9795e1f3cb36cd31ba42a04ff9c3 commit 1c12443ab8eba71a658fae4572147e56d1f84f66 upstream. The upcoming Intel Lynx Point chipset includes an xHCI host controller that can have ports switched from the EHCI host controller, just like the Intel Panther Point xHCI host. This time, ports from both EHCI hosts can be switched to the xHCI host controller. The PCI config registers to do the port switching are in the exact same place in the xHCI PCI configuration registers, with the same semantics. Hooray for shipping patches for next-gen hardware before the current gen hardware is even available for purchase! This patch should be backported to stable kernels as old as 3.0, that contain commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 1c12443ab8eba71a658fae4572147e56d1f84f66 upstream.

The upcoming Intel Lynx Point chipset includes an xHCI host controller
that can have ports switched from the EHCI host controller, just like
the Intel Panther Point xHCI host.  This time, ports from both EHCI
hosts can be switched to the xHCI host controller.  The PCI config
registers to do the port switching are in the exact same place in the
xHCI PCI configuration registers, with the same semantics.

Hooray for shipping patches for next-gen hardware before the current gen
hardware is even available for purchase!

This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: EHCI: fix crash during suspend on ASUS computers 2012-05-07T15:56:36+00:00 Alan Stern stern@rowland.harvard.edu 2012-04-24T18:07:22+00:00 a8eaeff79eb97662e2d06cc1919d902fc251e9da commit 151b61284776be2d6f02d48c23c3625678960b97 upstream. This patch (as1545) fixes a problem affecting several ASUS computers: The machine crashes or corrupts memory when going into suspend if the ehci-hcd driver is bound to any controllers. Users have been forced to unbind or unload ehci-hcd before putting their systems to sleep. After extensive testing, it was determined that the machines don't like going into suspend when any EHCI controllers are in the PCI D3 power state. Presumably this is a firmware bug, but there's nothing we can do about it except to avoid putting the controllers in D3 during system sleep. The patch adds a new flag to indicate whether the problem is present, and avoids changing the controller's power state if the flag is set. Runtime suspend is unaffected; this matters only for system suspend. However as a side effect, the controller will not respond to remote wakeup requests while the system is asleep. Hence USB wakeup is not functional -- but of course, this is already true in the current state of affairs. This fixes Bugzilla #42728. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Steven Rostedt <rostedt@goodmis.org> Tested-by: Andrey Rahmatullin <wrar@wrar.name> Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 151b61284776be2d6f02d48c23c3625678960b97 upstream.

This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

This fixes Bugzilla #42728.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert "usb: Fix build error due to dma_mask is not at pdev_archdata at ARM" 2012-05-07T15:56:35+00:00 Greg Kroah-Hartman gregkh@linuxfoundation.org 2012-04-30T01:09:01+00:00 ca288ca1de5957cb50e170dcdb5375c0e6467405 This reverts commit d39514c14bd941232976b68e2750dc725b90e724 which is e90fc3cb087ce5c5f81e814358222cd6d197b5db upstream as it causes oopses on some ppc systems. Reported-by: Chen Peter-B29397 <B29397@freescale.com> Cc: Ramneek Mehresh <ramneek.mehresh@freescale.com> Cc: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
This reverts commit d39514c14bd941232976b68e2750dc725b90e724 which is
e90fc3cb087ce5c5f81e814358222cd6d197b5db upstream as it causes oopses on
some ppc systems.

Reported-by: Chen Peter-B29397 <B29397@freescale.com>
Cc: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Cc: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EHCI: fix criterion for resuming the root hub 2012-05-07T15:56:34+00:00 Alan Stern stern@rowland.harvard.edu 2012-04-25T06:17:42+00:00 cb30a2fb48b70262f9989a0d0bbc2a42ec156a22 commit dc75ce9d929aabeb0843a6b1a4ab320e58ba1597 upstream. This patch (as1542) changes the criterion ehci-hcd uses to tell when it needs to resume the controller's root hub. A resume is needed when a port status change is detected, obviously, but only if the root hub is currently suspended. Right now the driver tests whether the root hub is running, and that is not the correct test. In particular, if the controller has died then the root hub should not be restarted. In addition, some buggy hardware occasionally requires the root hub to be running and sending out SOF packets even while it is nominally supposed to be suspended. In the end, the test needs to be changed. Rather than checking whether the root hub is currently running, the driver will now check whether the root hub is currently suspended. This will yield the correct behavior in all cases. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Peter Chen <B29397@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jonathan Nieder <jrnieder@gmail.com> 
commit dc75ce9d929aabeb0843a6b1a4ab320e58ba1597 upstream.

This patch (as1542) changes the criterion ehci-hcd uses to tell when
it needs to resume the controller's root hub.  A resume is needed when
a port status change is detected, obviously, but only if the root hub
is currently suspended.

Right now the driver tests whether the root hub is running, and that
is not the correct test.  In particular, if the controller has died
then the root hub should not be restarted.  In addition, some buggy
hardware occasionally requires the root hub to be running and
sending out SOF packets even while it is nominally supposed to be
suspended.

In the end, the test needs to be changed.  Rather than checking whether
the root hub is currently running, the driver will now check whether
the root hub is currently suspended.  This will yield the correct
behavior in all cases.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>