linux-stable.git/drivers/usb/host, branch linux-3.16.y Linux kernel stable tree USB: EHCI: Do not return -EPIPE when hub is disconnected 2020-04-28T18:03:05+00:00 Erkka Talvitie erkka.talvitie@vincit.fi 2019-12-11T08:08:39+00:00 6d64e68be54ead844232cf82cc2a2863c0a823c1 commit 64cc3f12d1c7dd054a215bc1ff9cc2abcfe35832 upstream. When disconnecting a USB hub that has some child device(s) connected to it (such as a USB mouse), then the stack tries to clear halt and reset device(s) which are _already_ physically disconnected. The issue has been reproduced with: CPU: IMX6D5EYM10AD or MCIMX6D5EYM10AE. SW: U-Boot 2019.07 and kernel 4.19.40. CPU: HP Proliant Microserver Gen8. SW: Linux version 4.2.3-300.fc23.x86_64 In this situation there will be error bit for MMF active yet the CERR equals EHCI_TUNE_CERR + halt. Existing implementation interprets this as a stall [1] (chapter 8.4.5). The possible conditions when the MMF will be active + halt can be found from [2] (Table 4-13). Fix for the issue is to check whether MMF is active and PID Code is IN before checking for the stall. If these conditions are true then it is not a stall. What happens after the fix is that when disconnecting a hub with attached device(s) the situation is not interpret as a stall. [1] [https://www.usb.org/document-library/usb-20-specification, usb_20.pdf] [2] [https://www.intel.com/content/dam/www/public/us/en/documents/ technical-specifications/ehci-specification-for-usb.pdf] Signed-off-by: Erkka Talvitie <erkka.talvitie@vincit.fi> Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/ef70941d5f349767f19c0ed26b0dd9eed8ad81bb.1576050523.git.erkka.talvitie@vincit.fi Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 64cc3f12d1c7dd054a215bc1ff9cc2abcfe35832 upstream.

When disconnecting a USB hub that has some child device(s) connected to it
(such as a USB mouse), then the stack tries to clear halt and
reset device(s) which are _already_ physically disconnected.

The issue has been reproduced with:

CPU: IMX6D5EYM10AD or MCIMX6D5EYM10AE.
SW: U-Boot 2019.07 and kernel 4.19.40.

CPU: HP Proliant Microserver Gen8.
SW: Linux version 4.2.3-300.fc23.x86_64

In this situation there will be error bit for MMF active yet the
CERR equals EHCI_TUNE_CERR + halt. Existing implementation
interprets this as a stall [1] (chapter 8.4.5).

The possible conditions when the MMF will be active + halt
can be found from [2] (Table 4-13).

Fix for the issue is to check whether MMF is active and PID Code is
IN before checking for the stall. If these conditions are true then
it is not a stall.

What happens after the fix is that when disconnecting a hub with
attached device(s) the situation is not interpret as a stall.

[1] [https://www.usb.org/document-library/usb-20-specification, usb_20.pdf]
[2] [https://www.intel.com/content/dam/www/public/us/en/documents/
     technical-specifications/ehci-specification-for-usb.pdf]

Signed-off-by: Erkka Talvitie <erkka.talvitie@vincit.fi>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/ef70941d5f349767f19c0ed26b0dd9eed8ad81bb.1576050523.git.erkka.talvitie@vincit.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: make sure interrupts are restored to correct state 2020-04-28T18:02:52+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2019-12-11T14:20:07+00:00 d16baec9a682ff8747dc7b1caf2d9a0ca9772c1a commit bd82873f23c9a6ad834348f8b83f3b6a5bca2c65 upstream. spin_unlock_irqrestore() might be called with stale flags after reading port status, possibly restoring interrupts to a incorrect state. If a usb2 port just finished resuming while the port status is read the spin lock will be temporary released and re-acquired in a separate function. The flags parameter is passed as value instead of a pointer, not updating flags properly before the final spin_unlock_irqrestore() is called. Fixes: 8b3d45705e54 ("usb: Fix xHCI host issues on remote wakeup.") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20191211142007.8847-7-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit bd82873f23c9a6ad834348f8b83f3b6a5bca2c65 upstream.

spin_unlock_irqrestore() might be called with stale flags after
reading port status, possibly restoring interrupts to a incorrect
state.

If a usb2 port just finished resuming while the port status is read
the spin lock will be temporary released and re-acquired in a separate
function. The flags parameter is passed as value instead of a pointer,
not updating flags properly before the final spin_unlock_irqrestore()
is called.

Fixes: 8b3d45705e54 ("usb: Fix xHCI host issues on remote wakeup.")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: handle some XHCI_TRUST_TX_LENGTH quirks cases as default behaviour. 2020-04-28T18:02:51+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2019-12-11T14:20:06+00:00 8026fabe90db30f32cb9225e33d51e37e414d216 commit 7ff11162808cc2ec66353fc012c58bb449c892c3 upstream. xhci driver claims it needs XHCI_TRUST_TX_LENGTH quirk for both Broadcom/Cavium and a Renesas xHC controllers. The quirk was inteded for handling false "success" complete event for transfers that had data left untransferred. These transfers should complete with "short packet" events instead. In these two new cases the false "success" completion is reported after a "short packet" if the TD consists of several TRBs. xHCI specs 4.10.1.1.2 say remaining TRBs should report "short packet" as well after the first short packet in a TD, but this issue seems so common it doesn't make sense to add the quirk for all vendors. Turn these events into short packets automatically instead. This gets rid of the "The WARN Successful completion on short TX for slot 1 ep 1: needs XHCI_TRUST_TX_LENGTH quirk" warning in many cases. Reported-by: Eli Billauer <eli.billauer@gmail.com> Reported-by: Ard Biesheuvel <ardb@kernel.org> Tested-by: Eli Billauer <eli.billauer@gmail.com> Tested-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20191211142007.8847-6-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 7ff11162808cc2ec66353fc012c58bb449c892c3 upstream.

xhci driver claims it needs XHCI_TRUST_TX_LENGTH quirk for both
Broadcom/Cavium and a Renesas xHC controllers.

The quirk was inteded for handling false "success" complete event for
transfers that had data left untransferred.
These transfers should complete with "short packet" events instead.

In these two new cases the false "success" completion is reported
after a "short packet" if the TD consists of several TRBs.
xHCI specs 4.10.1.1.2 say remaining TRBs should report "short packet"
as well after the first short packet in a TD, but this issue seems so
common it doesn't make sense to add the quirk for all vendors.

Turn these events into short packets automatically instead.

This gets rid of the  "The WARN Successful completion on short TX for
slot 1 ep 1: needs XHCI_TRUST_TX_LENGTH quirk" warning in many cases.

Reported-by: Eli Billauer <eli.billauer@gmail.com>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Eli Billauer <eli.billauer@gmail.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: fix USB3 device initiated resume race with roothub autosuspend 2020-01-11T02:05:02+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2019-12-11T14:20:03+00:00 bd3752fe1311d37cca1bbc0fe8e5876507bab301 commit 057d476fff778f1d3b9f861fdb5437ea1a3cfc99 upstream. A race in xhci USB3 remote wake handling may force device back to suspend after it initiated resume siganaling, causing a missed resume event or warm reset of device. When a USB3 link completes resume signaling and goes to enabled (UO) state a interrupt is issued and the interrupt handler will clear the bus_state->port_remote_wakeup resume flag, allowing bus suspend. If the USB3 roothub thread just finished reading port status before the interrupt, finding ports still in suspended (U3) state, but hasn't yet started suspending the hub, then the xhci interrupt handler will clear the flag that prevented roothub suspend and allow bus to suspend, forcing all port links back to suspended (U3) state. Example case: usb_runtime_suspend() # because all ports still show suspended U3 usb_suspend_both() hub_suspend(); # successful as hub->wakeup_bits not set yet ==> INTERRUPT xhci_irq() handle_port_status() clear bus_state->port_remote_wakeup usb_wakeup_notification() sets hub->wakeup_bits; kick_hub_wq() <== END INTERRUPT hcd_bus_suspend() xhci_bus_suspend() # success as port_remote_wakeup bits cleared Fix this by increasing roothub usage count during port resume to prevent roothub autosuspend, and by making sure bus_state->port_remote_wakeup flag is only cleared after resume completion is visible, i.e. after xhci roothub returned U0 or other non-U3 link state link on a get port status request. Issue rootcaused by Chiasheng Lee Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com> Reported-by: Lee, Chiasheng <chiasheng.lee@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [Mathias Nyman: Backport for 4.9 and 4.4 stable kernels] [bwh: Backported to 3.16: USB 3.0 SS is the highest speed we handle] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 057d476fff778f1d3b9f861fdb5437ea1a3cfc99 upstream.

A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.

When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.

If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.

Example case:
usb_runtime_suspend() # because all ports still show suspended U3
  usb_suspend_both()
    hub_suspend();   # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
  handle_port_status()
    clear bus_state->port_remote_wakeup
    usb_wakeup_notification()
      sets hub->wakeup_bits;
        kick_hub_wq()
<== END INTERRUPT
      hcd_bus_suspend()
        xhci_bus_suspend() # success as port_remote_wakeup bits cleared

Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.

Issue rootcaused by Chiasheng Lee

Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com>
Reported-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Mathias Nyman: Backport for 4.9 and 4.4 stable kernels]
[bwh: Backported to 3.16: USB 3.0 SS is the highest speed we handle]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: Fix port resume done detection for SS ports with LPM enabled 2020-01-11T02:04:49+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2019-03-22T15:50:15+00:00 fcb6c0a93d1b8b0e39cac0084daf83a0c99562a6 commit 6cbcf596934c8e16d6288c7cc62dfb7ad8eadf15 upstream. A suspended SS port in U3 link state will go to U0 when resumed, but can almost immediately after that enter U1 or U2 link power save states before host controller driver reads the port status. Host controller driver only checks for U0 state, and might miss the finished resume, leaving flags unclear and skip notifying usb code of the wake. Add U1 and U2 to the possible link states when checking for finished port resume. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [Mathias Nyman: backport to 3.18 stable.] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 6cbcf596934c8e16d6288c7cc62dfb7ad8eadf15 upstream.

A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.

Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.

Add U1 and U2 to the possible link states when checking for finished
port resume.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Mathias Nyman: backport to 3.18 stable.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: xhci: wait for CNR controller not ready bit in xhci resume 2019-12-19T15:58:06+00:00 Rick Tseng rtseng@nvidia.com 2019-10-04T11:59:30+00:00 c8f4c46277ceac473dd1aa5b80c116f0fdbb7080 commit a70bcbc322837eda1ab5994d12db941dc9733a7d upstream. NVIDIA 3.1 xHCI card would lose power when moving power state into D3Cold. Thus we need to wait for CNR bit to clear in xhci resume, just as in xhci init. [Minor changes to comment and commit message -Mathias] Signed-off-by: Rick Tseng <rtseng@nvidia.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-6-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: Add xhci as parameter to xhci_handshake()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit a70bcbc322837eda1ab5994d12db941dc9733a7d upstream.

NVIDIA 3.1 xHCI card would lose power when moving power state into D3Cold.
Thus we need to wait for CNR bit to clear in xhci resume, just as in
xhci init.

[Minor changes to comment and commit message -Mathias]
Signed-off-by: Rick Tseng <rtseng@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-6-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: Add xhci as parameter to xhci_handshake()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: Check all endpoints for LPM timeout 2019-12-19T15:58:06+00:00 Jan Schmidt jan@centricular.com 2019-10-04T11:59:28+00:00 5a800ae59799e6ee89a83ad3f3d8a452492af023 commit d500c63f80f2ea08ee300e57da5f2af1c13875f5 upstream. If an endpoint is encountered that returns USB3_LPM_DEVICE_INITIATED, keep checking further endpoints, as there might be periodic endpoints later that return USB3_LPM_DISABLED due to shorter service intervals. Without this, the code can set too high a maximum-exit-latency and prevent the use of multiple USB3 cameras that should be able to work. Signed-off-by: Jan Schmidt <jan@centricular.com> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-4-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit d500c63f80f2ea08ee300e57da5f2af1c13875f5 upstream.

If an endpoint is encountered that returns USB3_LPM_DEVICE_INITIATED, keep
checking further endpoints, as there might be periodic endpoints later
that return USB3_LPM_DISABLED due to shorter service intervals.

Without this, the code can set too high a maximum-exit-latency and
prevent the use of multiple USB3 cameras that should be able to work.

Signed-off-by: Jan Schmidt <jan@centricular.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci: Prevent device initiated U1/U2 link pm if exit latency is too long 2019-12-19T15:58:05+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2019-10-04T11:59:27+00:00 37f94b7b4b204258e6f62778d6cbff290cdb71fc commit cd9d9491e835a845c1a98b8471f88d26285e0bb9 upstream. If host/hub initiated link pm is prevented by a driver flag we still must ensure that periodic endpoints have longer service intervals than link pm exit latency before allowing device initiated link pm. Fix this by continue walking and checking endpoint service interval if xhci_get_timeout_no_hub_lpm() returns anything else than USB3_LPM_DISABLED While at it fix the split line error message Tested-by: Jan Schmidt <jan@centricular.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-3-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit cd9d9491e835a845c1a98b8471f88d26285e0bb9 upstream.

If host/hub initiated link pm is prevented by a driver flag we still must
ensure that periodic endpoints have longer service intervals than link pm
exit latency before allowing device initiated link pm.

Fix this by continue walking and checking endpoint service interval if
xhci_get_timeout_no_hub_lpm() returns anything else than USB3_LPM_DISABLED

While at it fix the split line error message

Tested-by: Jan Schmidt <jan@centricular.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: host: ohci: fix a race condition between shutdown and irq 2019-11-22T15:57:22+00:00 Yoshihiro Shimoda yoshihiro.shimoda.uh@renesas.com 2019-08-27T03:51:50+00:00 b45a88d1816dd13a879b5bd0bf360394382e041f commit a349b95d7ca0cea71be4a7dac29830703de7eb62 upstream. This patch fixes an issue that the following error is possible to happen when ohci hardware causes an interruption and the system is shutting down at the same time. [ 34.851754] usb 2-1: USB disconnect, device number 2 [ 35.166658] irq 156: nobody cared (try booting with the "irqpoll" option) [ 35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85 [ 35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) [ 35.187886] Workqueue: usb_hub_wq hub_event [ 35.192063] Call trace: [ 35.194509] dump_backtrace+0x0/0x150 [ 35.198165] show_stack+0x14/0x20 [ 35.201475] dump_stack+0xa0/0xc4 [ 35.204785] __report_bad_irq+0x34/0xe8 [ 35.208614] note_interrupt+0x2cc/0x318 [ 35.212446] handle_irq_event_percpu+0x5c/0x88 [ 35.216883] handle_irq_event+0x48/0x78 [ 35.220712] handle_fasteoi_irq+0xb4/0x188 [ 35.224802] generic_handle_irq+0x24/0x38 [ 35.228804] __handle_domain_irq+0x5c/0xb0 [ 35.232893] gic_handle_irq+0x58/0xa8 [ 35.236548] el1_irq+0xb8/0x180 [ 35.239681] __do_softirq+0x94/0x23c [ 35.243253] irq_exit+0xd0/0xd8 [ 35.246387] __handle_domain_irq+0x60/0xb0 [ 35.250475] gic_handle_irq+0x58/0xa8 [ 35.254130] el1_irq+0xb8/0x180 [ 35.257268] kernfs_find_ns+0x5c/0x120 [ 35.261010] kernfs_find_and_get_ns+0x3c/0x60 [ 35.265361] sysfs_unmerge_group+0x20/0x68 [ 35.269454] dpm_sysfs_remove+0x2c/0x68 [ 35.273284] device_del+0x80/0x370 [ 35.276683] hid_destroy_device+0x28/0x60 [ 35.280686] usbhid_disconnect+0x4c/0x80 [ 35.284602] usb_unbind_interface+0x6c/0x268 [ 35.288867] device_release_driver_internal+0xe4/0x1b0 [ 35.293998] device_release_driver+0x14/0x20 [ 35.298261] bus_remove_device+0x110/0x128 [ 35.302350] device_del+0x148/0x370 [ 35.305832] usb_disable_device+0x8c/0x1d0 [ 35.309921] usb_disconnect+0xc8/0x2d0 [ 35.313663] hub_event+0x6e0/0x1128 [ 35.317146] process_one_work+0x1e0/0x320 [ 35.321148] worker_thread+0x40/0x450 [ 35.324805] kthread+0x124/0x128 [ 35.328027] ret_from_fork+0x10/0x18 [ 35.331594] handlers: [ 35.333862] [<0000000079300c1d>] usb_hcd_irq [ 35.338126] [<0000000079300c1d>] usb_hcd_irq [ 35.342389] Disabling IRQ #156 ohci_shutdown() disables all the interrupt and rh_state is set to OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF is possible to be set by start_ed_unlink() which is called: ohci_irq() -> process_done_list() -> takeback_td() -> start_ed_unlink() So, ohci_irq() has the following condition, the issue happens by &ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and ohci->rh_state = OHCI_RH_HALTED: /* interrupt for some other device? */ if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED)) return IRQ_NOTMINE; To fix the issue, ohci_shutdown() holds the spin lock while disabling the interruption and changing the rh_state flag to prevent reenable the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also calls the ohci_shutdown() and it already held the spin lock, so that the patch makes a new function as _ohci_shutdown(). This patch is inspired by a Renesas R-Car Gen3 BSP patch from Tho Vu. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: - Drop change in io_watchdog_func() - Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit a349b95d7ca0cea71be4a7dac29830703de7eb62 upstream.

This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.

[   34.851754] usb 2-1: USB disconnect, device number 2
[   35.166658] irq 156: nobody cared (try booting with the "irqpoll" option)
[   35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85
[   35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[   35.187886] Workqueue: usb_hub_wq hub_event
[   35.192063] Call trace:
[   35.194509]  dump_backtrace+0x0/0x150
[   35.198165]  show_stack+0x14/0x20
[   35.201475]  dump_stack+0xa0/0xc4
[   35.204785]  __report_bad_irq+0x34/0xe8
[   35.208614]  note_interrupt+0x2cc/0x318
[   35.212446]  handle_irq_event_percpu+0x5c/0x88
[   35.216883]  handle_irq_event+0x48/0x78
[   35.220712]  handle_fasteoi_irq+0xb4/0x188
[   35.224802]  generic_handle_irq+0x24/0x38
[   35.228804]  __handle_domain_irq+0x5c/0xb0
[   35.232893]  gic_handle_irq+0x58/0xa8
[   35.236548]  el1_irq+0xb8/0x180
[   35.239681]  __do_softirq+0x94/0x23c
[   35.243253]  irq_exit+0xd0/0xd8
[   35.246387]  __handle_domain_irq+0x60/0xb0
[   35.250475]  gic_handle_irq+0x58/0xa8
[   35.254130]  el1_irq+0xb8/0x180
[   35.257268]  kernfs_find_ns+0x5c/0x120
[   35.261010]  kernfs_find_and_get_ns+0x3c/0x60
[   35.265361]  sysfs_unmerge_group+0x20/0x68
[   35.269454]  dpm_sysfs_remove+0x2c/0x68
[   35.273284]  device_del+0x80/0x370
[   35.276683]  hid_destroy_device+0x28/0x60
[   35.280686]  usbhid_disconnect+0x4c/0x80
[   35.284602]  usb_unbind_interface+0x6c/0x268
[   35.288867]  device_release_driver_internal+0xe4/0x1b0
[   35.293998]  device_release_driver+0x14/0x20
[   35.298261]  bus_remove_device+0x110/0x128
[   35.302350]  device_del+0x148/0x370
[   35.305832]  usb_disable_device+0x8c/0x1d0
[   35.309921]  usb_disconnect+0xc8/0x2d0
[   35.313663]  hub_event+0x6e0/0x1128
[   35.317146]  process_one_work+0x1e0/0x320
[   35.321148]  worker_thread+0x40/0x450
[   35.324805]  kthread+0x124/0x128
[   35.328027]  ret_from_fork+0x10/0x18
[   35.331594] handlers:
[   35.333862] [<0000000079300c1d>] usb_hcd_irq
[   35.338126] [<0000000079300c1d>] usb_hcd_irq
[   35.342389] Disabling IRQ #156

ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
 ohci_irq()
  -> process_done_list()
   -> takeback_td()
    -> start_ed_unlink()

So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:

	/* interrupt for some other device? */
	if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
		return IRQ_NOTMINE;

To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().

This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
 - Drop change in io_watchdog_func()
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: wusbcore: fix unbalanced get/put cluster_id 2019-11-22T15:57:05+00:00 Phong Tran tranmanphong@gmail.com 2019-07-24T02:06:01+00:00 87df15bad1762699a4fe808a8567ce18a4293e51 commit f90bf1ece48a736097ea224430578fe586a9544c upstream. syzboot reported that https://syzkaller.appspot.com/bug?extid=fd2bd7df88c606eea4ef There is not consitency parameter in cluste_id_get/put calling. In case of getting the id with result is failure, the wusbhc->cluster_id will not be updated and this can not be used for wusb_cluster_id_put(). Tested report https://groups.google.com/d/msg/syzkaller-bugs/0znZopp3-9k/oxOrhLkLEgAJ Reproduce and gdb got the details: 139 addr = wusb_cluster_id_get(); (gdb) n 140 if (addr == 0) (gdb) print addr $1 = 254 '\376' (gdb) n 142 result = __hwahc_set_cluster_id(hwahc, addr); (gdb) print result $2 = -71 (gdb) break wusb_cluster_id_put Breakpoint 3 at 0xffffffff836e3f20: file drivers/usb/wusbcore/wusbhc.c, line 384. (gdb) s Thread 2 hit Breakpoint 3, wusb_cluster_id_put (id=0 '\000') at drivers/usb/wusbcore/wusbhc.c:384 384 id = 0xff - id; (gdb) n 385 BUG_ON(id >= CLUSTER_IDS); (gdb) print id $3 = 255 '\377' Reported-by: syzbot+fd2bd7df88c606eea4ef@syzkaller.appspotmail.com Signed-off-by: Phong Tran <tranmanphong@gmail.com> Link: https://lore.kernel.org/r/20190724020601.15257-1-tranmanphong@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit f90bf1ece48a736097ea224430578fe586a9544c upstream.

syzboot reported that
https://syzkaller.appspot.com/bug?extid=fd2bd7df88c606eea4ef

There is not consitency parameter in cluste_id_get/put calling.
In case of getting the id with result is failure, the wusbhc->cluster_id
will not be updated and this can not be used for wusb_cluster_id_put().

Tested report
https://groups.google.com/d/msg/syzkaller-bugs/0znZopp3-9k/oxOrhLkLEgAJ

Reproduce and gdb got the details:

139		addr = wusb_cluster_id_get();
(gdb) n
140		if (addr == 0)
(gdb) print addr
$1 = 254 '\376'
(gdb) n
142		result = __hwahc_set_cluster_id(hwahc, addr);
(gdb) print result
$2 = -71
(gdb) break wusb_cluster_id_put
Breakpoint 3 at 0xffffffff836e3f20: file drivers/usb/wusbcore/wusbhc.c, line 384.
(gdb) s
Thread 2 hit Breakpoint 3, wusb_cluster_id_put (id=0 '\000') at drivers/usb/wusbcore/wusbhc.c:384
384		id = 0xff - id;
(gdb) n
385		BUG_ON(id >= CLUSTER_IDS);
(gdb) print id
$3 = 255 '\377'

Reported-by: syzbot+fd2bd7df88c606eea4ef@syzkaller.appspotmail.com
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Link: https://lore.kernel.org/r/20190724020601.15257-1-tranmanphong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>