linux-stable.git/drivers/usb/host, branch linux-2.6.33.y

QE/FHCI: fixed the CONTROL bug

2011-11-07T21:47:21+00:00

commit 273d23574f9dacd9c63c80e7d63639a669aad441 upstream.

For USB CONTROL transaction, when the data length is zero,
the IN package is needed to finish this transaction in status stage.

Signed-off-by: Jerry Huang 
Signed-off-by: Greg Kroah-Hartman

xhci-mem.c: Check for ring->first_seg != NULL

2011-11-07T21:47:11+00:00

commit 0e6c7f746ea99089fb3263709075c20485a479ae upstream.

There are 2 situations wherein the xhci_ring* might not get freed:
- When xhci_ring_alloc() -> xhci_segment_alloc() returns NULL and
  we goto the fail: label in xhci_ring_alloc. In this case, the ring
  will not get kfreed.
- When the num_segs argument to xhci_ring_alloc is passed as 0 and
  we try to free the rung after that.
  ( This doesn't really happen as of now in the code but we seem to
    be entertaining num_segs=0 in xhci_ring_alloc )

This should be backported to kernels as old as 2.6.31.

Signed-off-by: Kautuk Consul 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ehci_bus_resume().

2011-11-07T21:46:39+00:00

commit d0f2fb2500b1c5fe4967eb45d8c9bc758d7aef80 upstream.

From EHCI Spec p.28 HC should clear PORT_SUSPEND when SW clears
PORT_RESUME. In Intel Oaktrail platform, MPH (Multi-Port Host
Controller) core clears PORT_SUSPEND directly when SW sets PORT_RESUME
bit. If we rely on PORT_SUSPEND bit to stop USB resume, we will miss
the action of clearing PORT_RESUME. This will cause unexpected long
resume signal on USB bus.

Signed-off-by: Wang Zhi 
Signed-off-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: xhci: fix OS want to own HC

2011-08-29T21:32:50+00:00

commit 6768458b17f9bf48a4c3a34e49b20344091b5f7e upstream.

Software should set XHCI_HC_OS_OWNED bit to request ownership of xHC.

This patch should be backported to kernels as far back as 2.6.31.

Signed-off-by: JiSheng Zhang 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

EHCI: fix direction handling for interrupt data toggles

2011-08-08T17:36:04+00:00

commit e04f5f7e423018bcec84c11af2058cdce87816f3 upstream.

This patch (as1480) fixes a rather obscure bug in ehci-hcd.  The
qh_update() routine needs to know the number and direction of the
endpoint corresponding to its QH argument.  The number can be taken
directly from the QH data structure, but the direction isn't stored
there.  The direction is taken instead from the first qTD linked to
the QH.

However, it turns out that for interrupt transfers, qh_update() gets
called before the qTDs are linked to the QH.  As a result, qh_update()
computes a bogus direction value, which messes up the endpoint toggle
handling.  Under the right combination of circumstances this causes
usb_reset_endpoint() not to work correctly, which causes packets to be
dropped and communications to fail.

Now, it's silly for the QH structure not to have direct access to all
the descriptor information for the corresponding endpoint.  Ultimately
it may get a pointer to the usb_host_endpoint structure; for now,
adding a copy of the direction flag solves the immediate problem.

This allows the Spyder2 color-calibration system (a low-speed USB
device that sends all its interrupt data packets with the toggle set
to 0 and hance requires constant use of usb_reset_endpoint) to work
when connected through a high-speed hub.  Thanks to Graeme Gill for
supplying the hardware that allowed me to track down this bug.

Signed-off-by: Alan Stern 
Reported-by: Graeme Gill 
Signed-off-by: Greg Kroah-Hartman

EHCI: only power off port if over-current is active

2011-08-08T17:36:04+00:00

commit 81463c1d707186adbbe534016cd1249edeab0dac upstream.

MAX4967 USB power supply chip we use on our boards signals over-current when
power is not enabled; once it's enabled, over-current signal returns to normal.
That unfortunately caused the endless stream of "over-current change on port"
messages. The EHCI root hub code reacts on every over-current signal change
with powering off the port -- such change event is generated the moment the
port power is enabled, so once enabled the power is immediately cut off.
I think we should only cut off power when we're seeing the active over-current
signal, so I'm adding such check to that code. I also think that the fact that
we've cut off the port power should be reflected in the result of GetPortStatus
request immediately, hence I'm adding a PORTSCn register readback after write...

Signed-off-by: Sergei Shtylyov 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

xhci: Reject double add of active endpoints.

2011-07-13T03:31:23+00:00

commit fa75ac379e63c2864e9049b5e8615e40f65c1e70 upstream.

While trying to switch a UAS device from the BOT configuration to the UAS
configuration via the bConfigurationValue file, Tanya ran into an issue in
the USB core.  usb_disable_device() sets entries in udev->ep_out and
udev->ep_out to NULL, but doesn't call into the xHCI bandwidth management
functions to remove the BOT configuration endpoints from the xHCI host's
internal structures.

The USB core would then attempt to add endpoints for the UAS
configuration, and some of the endpoints had the same address as endpoints
in the BOT configuration.  The xHCI driver blindly added the endpoints
again, but the xHCI host controller rejected the Configure Endpoint
command because active endpoints were added without being dropped.

Make the xHCI driver reject calls to xhci_add_endpoint() that attempt to
add active endpoints without first calling xhci_drop_endpoint().

This should be backported to kernels as old as 2.6.31.

Signed-off-by: Sarah Sharp 
Reported-by: Tanya Brokhman 
Signed-off-by: Greg Kroah-Hartman

USB: xhci - fix interval calculation for FS isoc endpoints

2011-06-23T22:28:41+00:00

commit cd3c18ba2fac14b34d03cae111f215009735ea06 upstream.

Full-speed isoc endpoints specify interval in exponent based form in
frames, not microframes, so we need to adjust accordingly.

NEC xHCI host controllers will return an error code of 0x11 if a full
speed isochronous endpoint is added with the Interval field set to
something less than 3 (2^3 = 8 microframes, or one frame).  It is
impossible for a full speed device to have an interval smaller than one
frame.

This was always an issue in the xHCI driver, but commit
dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math in
xhci_get_endpoint_interval()" removed the clamping of the minimum value
in the Interval field, which revealed this bug.

This needs to be backported to stable kernels back to 2.6.31.

Reported-by: Matt Evans 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

xhci: Fix full speed bInterval encoding.

2011-06-23T22:28:37+00:00

commit b513d44751bfb609a3c20463f764c8ce822d63e9 upstream.

Dmitry's patch

dfa49c4ad120a784ef1ff0717168aa79f55a483a USB: xhci - fix math in xhci_get_endpoint_interval()

introduced a bug.  The USB 2.0 spec says that full speed isochronous endpoints'
bInterval must be decoded as an exponent to a power of two (e.g. interval =
2^(bInterval - 1)).  Full speed interrupt endpoints, on the other hand, don't
use exponents, and the interval in frames is encoded straight into bInterval.

Dmitry's patch was supposed to fix up the full speed isochronous to parse
bInterval as an exponent, but instead it changed the *interrupt* endpoint
bInterval decoding.  The isochronous endpoint encoding was the same.

This caused full speed devices with interrupt endpoints (including mice, hubs,
and USB to ethernet devices) to fail under NEC 0.96 xHCI host controllers:

[  100.909818] xhci_hcd 0000:06:00.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x99, new slot info = 0x38100000
[  100.909821] xhci_hcd 0000:06:00.0: xhci_check_bandwidth called for udev ffff88011f0ea000
...
[  100.910187] xhci_hcd 0000:06:00.0: ERROR: unexpected command completion code 0x11.
[  100.910190] xhci_hcd 0000:06:00.0: xhci_reset_bandwidth called for udev ffff88011f0ea000

When the interrupt endpoint was added and a Configure Endpoint command was
issued to the host, the host controller would return a very odd error message
(0x11 means "Slot Not Enabled", which isn't true because the slot was enabled).
Probably the host controller was getting very confused with the bad encoding.

Signed-off-by: Sarah Sharp 
Cc: Dmitry Torokhov 
Reported-by: Thomas Lindroth 
Tested-by: Thomas Lindroth 
Signed-off-by: Greg Kroah-Hartman

USB: xhci - fix math in xhci_get_endpoint_interval()

2011-04-22T15:50:04+00:00

commit dfa49c4ad120a784ef1ff0717168aa79f55a483a upstream.

When parsing exponent-expressed intervals we subtract 1 from the
value and then expect it to match with original + 1, which is
highly unlikely, and we end with frequent spew:

	usb 3-4: ep 0x83 - rounding interval to 512 microframes

Also, parsing interval for fullspeed isochronous endpoints was
incorrect - according to USB spec they use exponent-based
intervals (but xHCI spec claims frame-based intervals). I trust
USB spec more, especially since USB core agrees with it.

This should be queued for stable kernels back to 2.6.31.

Reviewed-by: Micah Elizabeth Scott 
Signed-off-by: Dmitry Torokhov 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman